Table of Contents
Advertisement
Item
[ISO SELECT]
[NATIVE ISO]
[800BASE ISO]
[5000BASE ISO]
[SETTING(GAIN)]
[GAIN OFFSET SW]
[OFFSET LEVEL]
[SHUTTER]
[SW]
[DISPLAY MODE]
[MODE]
[SYNCHRO deg]
[SYNCHRO sec]
[PRESET VALUE deg]
[PRESET VALUE sec]
[TEST SIG]
[TEST SIG SEL]
[COLOR BARS TYPE]
[DETAIL]
[SW]
[CORING]
[MASTER LEVEL]
[SKIN DETAIL]
[SW]
[TABLE SELECT]
Chapter 10 Menu Operations — Menu list
Selects the operation of ISO.
[NATIVE ONLY], [800BASE], [5000BASE]
f Factory setting: [NATIVE ONLY]
Sets the value when [NATIVE ONLY] is selected.
[800], [5000]
The value will be [400] and [2500] when [HIGH SPEED] is set to [ON].
f Factory setting: [800]
Sets the value when [800BASE] is selected.
[200], [250], [320], [400], [500], [640], [800], [1000], [1250], [1600], [2000], [2500], [3200], [4000],
[5000], [6400], [8000], [10000], [12800]
It will be [200], [250], [320], [400], [500], [640], [800], [1000], [1250], [1600], [2000], [2500], [3200], [4000],
[5000], and [6400] when the setting of [HIGH SPEED] is [ON].
f Factory setting: [800]
Sets the value when [5000BASE] is selected.
[1250], [1600], [2000], [2500], [3200], [4000], [5000], [6400], [8000], [10000], [12800]
It will be [1250], [1600], [2000], [2500], [3200], [4000], [5000], and [6400] when [HIGH SPEED] is set to
[ON].
f Factory setting: [5000]
Sets the value when [dB] is selected.
[0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB], [24dB]
f Factory setting: [0dB]
Sets whether to perform fine adjustment of control when [dB] is selected.
[ON], [OFF]
f Factory setting: [OFF]
Sets the fine adjustment level.
[0.0dB] - [0.9dB] (0.1 dB step)
f Factory setting: [0dB]
Enables/disables the shutter function.
[ON], [OFF]
f Factory setting: [ON]
Sets the shutter display unit.
[sec]: Displays in time.
[deg]: Displays at shutter open angle.
f Factory setting: [deg]
Switches the shutter control mode.
[PRESET]: Selects the mode from 12 modes inside the memory.
[SYNCHRO]: Selects the mode from the operable range.
f Factory setting: [PRESET]
Sets the value of angle control ([deg]).
[1.0]...[358.0]
f Factory setting: [180.0]
Sets the value of time control ([sec]). The lowest value changes depending on the frame rate ([FPS]) value.
[1/60] - [1/250]
f Factory setting: [1/48]
Selects the angle control ([deg]) value from the maximum of 12 values set in the control panel.
Preset values that can be selected in the factory setting are [11.5], [22.5], [45.0], [90.0], [120.0], [144.0],
[172.8], [180.0], [270.0], and [358.0].
f Factory setting: [180.0]
Selects the time control ([sec]) value from the maximum of 12 values set in the control panel.
Preset values that can be selected in the factory setting are [1/60], [1/100], [1/120], [1/250], [1/500],
[1/1000], and [1/2000].
f Factory setting: [1/60]
Sets the test signal output.
[OFF]: Does not output a test signal.
[BARS]: Outputs the color bar set in [COLOR BARS TYPE].
f Factory setting: [OFF]
Set the color bar to be used.
[SMPTE]: Uses the color bar in the SMPTE standard.
[FULL]: Uses full color bars.
f Factory setting: [SMPTE]
Enables/disables the detail function.
[ON], [OFF]
f Factory setting: [OFF]
Sets the coring amount for the detail signal.
[0] - [60]
f Factory setting: [1]
Sets the effect level for the detail signal.
[−31]...[31]
f Factory setting: [0]
Enables/disables the skin tone detail function.
[OFF], [ON]
f Factory setting: [OFF]
Selects the table for the skin tone detail.
[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]
f Factory setting: [A]
– 110 –
Description of settings
Advertisement
Table of Contents
