Table of Contents
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Hanging the Fan
7
Hood
Remote Control
13
1
M3608-01 • 05/09/16 • © 2016 Hunter Fan Company
Ceiling Plate
Ladder
3
Canopy
Wiring
9
Operation, Maintenance
& Cleaning
15
www.HunterFan.com
1.888.830.1326
Top Housing
4
5
Blades
9
12
Troubleshooting
?
?
?
16
18
Advertisement
Table of Contents
Related Manuals for Hunter M3608-01
Summary of Contents for Hunter M3608-01
- Page 1 To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Operation, Maintenance Hood Remote Control & Cleaning Troubleshooting M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
-
Page 2: What To Expect With Your Installation
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... -
Page 3: Tools Needed
The symbols can be used to identify Power Drill 9/64” Drill Bit the appropriate hardware for each step. Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... -
Page 4: Ceiling Plate
To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the Refer to warning w.1 on pg. 2 outlet box associated with the wall switch location. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... -
Page 5: Top Housing
M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... - Page 6 The wires can be cut, but leave at the grounding screw in the smaller least 8” extending from the top of screw hole. These screws can be found the canopy. in the hardware bag. 8” 3/8” M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
-
Page 7: Hanging The Fan
Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. Note: Fan style may vary. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... - Page 8 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 10 Note: The slots in the canopy must three canopy screws. remain engaged while swinging the canopy for alignment. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 11 Note: Should you need to remove the trim ring, press firmly on opposite sides of the trim ring. The tabs will flex out releasing the canopy trim ring. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 12 Blades www.HunterFan.com 1.888.830.1326 Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the hardware bag. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 13 Make sure the hood is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 14 When necessary, replace with Make sure to line up the colored place and then tighten all three bulb of the same type and markings on the connectors. screws. wattage. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
-
Page 15: Remote Control
High button for 4 seconds to pair the remote. To prevent faulty operation, please ensure all other ceiling fans within range are turned off at the wall switch while pairing. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company... - Page 16 Insert and tighten the screws. Do not over tighten. Note: For rocker-style cover plates, break off the tabs by pushing outward. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
- Page 17 To switch the direction of air flow, move the For cleaning the fan, use soft brushes or reverse switch to the opposite position. cloths to prevent scratching. Cleaning products may damage the finishes. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...
-
Page 18: Troubleshooting
• Install a fresh battery. the switch housing. your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue. M3608-01 • 05/09/16 • © 2016 Hunter Fan Company...