Table of Contents
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Preparation
Downrod
6
Blades
Switch Housing
12
1
M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company
Mounting Options
Ladder
3
Wiring
7
Maintenance &
Cleaning
13
Ceiling Bracket
4
5
Canopy
10
11
Troubleshooting
?
?
?
15
16
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hunter M3537-01
Summary of Contents for Hunter M3537-01
- Page 1 We are proud of our work and appreciate the opportunity to Preparation Downrod Wiring Canopy supply you with the best ceiling fan available anywhere in the world. Maintenance & Blades Switch Housing Cleaning Troubleshooting M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
-
Page 2: What To Expect With Your Installation
10 feet or higher with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. Check box to see fan weight Assess ceiling angle Select a downrod length M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... -
Page 3: Tools Needed
Tools Needed Pliers Wire Strippers Screwdrivers Ladder Power Drill 9/64” Drill Bit (optional) (optional) If mounting to a support structure, you will also need these tools. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... -
Page 4: Mounting Options
You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... -
Page 5: Ceiling Bracket
To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... - Page 6 Ceiling Bracket (continued) Preparation Time Saver Tip: Get a helper to insert grommets, found in hardware bag, into the blades while you’re doing the next couple of steps. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 7 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 8 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 9 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 11 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
- Page 12 M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
-
Page 13: Switch Housing
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... - Page 14 Tighten all three screws. Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
-
Page 15: Maintenance And Cleaning
Changing the direction of air Cleaning the fan - use soft flow - move the reverse switch brushes or cloths to prevent to the opposite position. scratching. Cleaning products may damage the finishes. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company... -
Page 16: Troubleshooting
• Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 10. • Check the plug connection in the switch housing. M3537-01 • 06/25/15 • © 2013–2015 Hunter Fan Company...
Need help?
Do you have a question about the M3537-01 and is the answer not in the manual?
Questions and answers