Table of Contents
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Downrod
6
Hood
Remote Control
13
1
M3607-01 • 05/06/16 • © 2016 Hunter Fan Company
Mounting Options
Ladder
3
Wiring
Canopy
9
Operation, Maintenance
& Cleaning
15
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Blades
11
12
Troubleshooting
?
?
?
16
18
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hunter M3607
Summary of Contents for Hunter M3607
- Page 1 To register your fan, please visit: www.HunterFan.com/register Save your receipt for proof of purchase. Operation, Maintenance Hood Remote Control & Cleaning Troubleshooting M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
-
Page 2: What To Expect With Your Installation
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company... -
Page 3: Tools Needed
The symbols can be used to identify Power Drill 9/64” Drill Bit the appropriate hardware for each step. Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company... -
Page 4: Mounting Options
You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M3607-01 • 05/06/16 • © 2016 Hunter Fan Company... -
Page 5: Ceiling Bracket
To avoid possible electrical shock, before 1-888-830-1326. installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company... - Page 6 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 7 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 8 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 11 Lift the canopy into place so that Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 12 Blades www.HunterFan.com 1.888.830.1326 Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the hardware bag. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 13 Make sure the hood is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 14 When necessary, replace with Make sure to line up the colored place and then tighten all three bulb of the same type and markings on the connectors. screws. wattage. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
-
Page 15: Remote Control
High button for 4 seconds to pair the remote. To prevent faulty operation, please ensure all other ceiling fans within range are turned off at the wall switch while pairing. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company... - Page 16 Insert and tighten the screws. Do not over tighten. Note: For rocker-style cover plates, break off the tabs by pushing outward. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
- Page 17 To switch the direction of air flow, move the For cleaning the fan, use soft brushes or reverse switch to the opposite position. cloths to prevent scratching. Cleaning products may damage the finishes. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
-
Page 18: Troubleshooting
• Install a fresh battery. the switch housing. your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue. M3607-01 • 05/06/16 • © 2016 Hunter Fan Company...
Need help?
Do you have a question about the M3607 and is the answer not in the manual?
Questions and answers