Advertisement

Quick Links

ENGLISH
www.HunterFanInternational.com
MB012-01 • 01/07/14 • © Hunter Fan Company

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Maribel Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Hunter Maribel Series

  • Page 1 ENGLISH www.HunterFanInternational.com MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 3 We are proud of our work and appreciate the opportunity to Preparation Downrod Wiring Canopy supply you with the best ceiling fan available anywhere in the world. Maintenance Blades Switch Housing & Cleaning Troubleshooting MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 4: What To Expect With Your Installation

    - To reduce the risk of fire, electrical shock, or motor You may need a Standard Downrod damage, use only Hunter Solid State Speed Controls. friend to help you. for ceilings 2,4-3 m (8-10 feet) high w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan.
  • Page 5: Tools Needed

    Tools Needed www.HunterFanInternational.com Pliers Wire Strippers 11/32” Wrench Ladder Power Drill 9/64” Drill Bit Screwdrivers (optional) (optional) If mounting to a support structure, you will also need these tools. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 6: Mounting Options

    You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common MB012-01 • 01/07/14 • © Hunter Fan Company MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 7: Ceiling Bracket

    Refer to warning w.1 on pg. 2 box associated with the wall switch location. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 8 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 9 Save the screws. They will be next couple of steps. needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 10 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 3 m (10’) or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 11 DO NOT can be inserted. extending from the top of HAND TIGHTEN. the downrod. 20 cm 1 cm (8”) (3/8”) If the setscrew is not tightened securely, the fan may fall. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 12 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 13 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 14 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 15 MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 16: Switch Housing

    Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 17 Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 18: Maintenance And Cleaning

    Cleaning the fan - use soft from high to off. flow - move the reverse switch brushes or cloths to prevent to the opposite position. scratching. Cleaning products may damage the finishes. MB012-01 • 01/07/14 • © Hunter Fan Company...
  • Page 19: Troubleshooting

    • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 11. • Check the plug connection in the switch housing. MB012-01 • 01/07/14 • © Hunter Fan Company...

Table of Contents