Stairville MaTrixx TLB-20 MK-II RGBW User Manual
  1. Manuals
  2. Brands
  3. Stairville Manuals
  4. Lighting Equipment
  5. MaTrixx TLB-20 MK-II RGBW
  6. User manual

Stairville MaTrixx TLB-20 MK-II RGBW User Manual

Led flower effect
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MaTrixx TLB-20
MK-II RGBW
LED flower effect
user manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MaTrixx TLB-20 MK-II RGBW and is the answer not in the manual?

Questions and answers

Related Manuals for Stairville MaTrixx TLB-20 MK-II RGBW

Summary of Contents for Stairville MaTrixx TLB-20 MK-II RGBW

  • Page 1 MaTrixx TLB-20 MK-II RGBW LED flower effect user manual...
  • Page 2 Musikhaus Thomann e.K. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 15.10.2012...

  • Page 3: Table Of Contents

    Table of contents Table of contents General notes............................... 5 Safety instructions............................. 8 Features............................... 12 Installation..............................13 Starting up..............................16 Connections and operating elements................... 19 Operation..............................24 7.1 Starting up the device........................24 7.2 Main menu............................24 7.3 Menu overview..........................30 7.4 Functions in 2-channel DMX mode...................
  • Page 4 Table of contents Technical specifications........................38 Protecting the environment......................39 LED flower effect...

  • Page 5: General Notes

    General notes General notes This user manual contains important information on safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device, include the manual for the next owner.
  • Page 6 General notes Signal word Meaning DANGER! This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided. WARNING! This combination of symbol and signal word indicates a possible dangerous situation that can result in death or serious injury if it is not avoided.
  • Page 7 General notes Warning signs Type of danger Warning – suspended load. Warning – danger zone. MaTrixx TLB-20MK-II RGBW...

  • Page 8: Safety Instructions

    Safety instructions Safety instructions Intended use This device is intended to be used as an electronic illumination effect using LED technics. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
  • Page 9 Safety instructions DANGER! Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. DANGER! Electric shock caused by short-circuit Always use proper ready-made insulated mains cabling (power cord) with a pro‐ tective contact plug.
  • Page 10 Safety instructions WARNING! Eye damage caused by high light intensity Never look directly into the light source. WARNING! Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights. NOTICE! Risk of fire Do not cover the device nor any ventilation slots.
  • Page 11 Safety instructions NOTICE! Operating conditions This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. NOTICE! Power supply Before connecting the device, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker.

  • Page 12: Features

    Features Features The LED effects projector is specially suited for professional lighting tasks, such as at events, on rock stages, in theatres and musicals. It is characterized by low power consumption and long life time. Special features of this device: 192 LEDs (48 ×...

  • Page 13: Installation

    Installation Installation Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the device against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
  • Page 14 Installation NOTICE! Risk of overheating The distance between the light output and the illuminated surface must be more than 0.5 m (19.7 in). Always ensure sufficient ventilation. The ambient temperature must always be below 40 °C (104 °F). NOTICE! Use of stands When mounting the device onto a stand, ensure that the stand is in a safe and stable position and that the weight of the device does not exceed the maximum permissible load capacity of the stand.
  • Page 15 Installation NOTICE! Possible data transmission errors For error-free operation make use of dedicated DMX cables and do not use ordi‐ nary microphone cables. Never connect the DMX output to audio devices such as mixers or amplifiers. DMX connections The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for pin assignment.

  • Page 16: Starting Up

    Starting up Starting up Establish all connections as long as the unit is switched off. Use the shortest possible high- quality cables for all connections. LED flower effect...
  • Page 17 Starting up Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device. Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain.
  • Page 18 Starting up Connections in master/slave When you configure a group of devices in master/slave mode, the first unit will control the mode other units for an automatic, sound-activated, synchronized show. This function is ideal when you want to start a show immediately. Connect the DMX output of the master device to the DMX input of the first slave device.

  • Page 19: Connections And Operating Elements

    Connections and operating elements Connections and operating elements Front panel MaTrixx TLB-20MK-II RGBW...
  • Page 20 Connections and operating elements 1, 2, 3 Projection lenses. 4 Mounting bracket with locking screws. LED flower effect...
  • Page 21 Connections and operating elements Rear panel MaTrixx TLB-20MK-II RGBW...
  • Page 22 Connections and operating elements 5 DMX Out DMX output. 6 DMX In DMX input. 7 Safety eye. 8 [Mode] button Calls the main menu. 9 [Setup] button Calls submenus to adjust values. 10 Display. 11 [UP] button To increase the displayed value by one. LED flower effect...
  • Page 23 Connections and operating elements 12 Taste [Down] To decrease the displayed value by one. 13 Power In IEC chassis connector for the mains cable, with fuse holder underneath. Beneath the connector, the proper operating voltage is indicated. MaTrixx TLB-20MK-II RGBW...

  • Page 24: Operation

    Operation Operation 7.1 Starting up the device Connect the unit to the power grid to start the operation. After a few seconds the display shows a running reset. Then the unit is ready for use. 7.2 Main menu Press [Mode] to call the main menu and select an operating mode. Use the [UP] and [Down] to change the respectively shown value.
  • Page 25 Operation Operating mode ‘Built-in auto‐ A built-in automatic show can only be activated if the unit is working in standalone mode or as matic show’ master device in a master / slave combination. This setting is only relevant if the unit is not controlled via DMX.
  • Page 26 Operation Operating mode ‘Automatic’ Automatic operation can only be activated if the unit is working in standalone mode or as master device in a master / slave combination. This setting is only relevant if the unit is not controlled via DMX. Press [Mode] repeatedly until the display shows ‘Auto’...
  • Page 27 Operation DMX mode This setting is only relevant if the unit is controlled via DMX. Press [Mode] repeatedly until the display shows ‘dxxx’ . Now you can set the number of the first DMX channel to be used by the device (DMX address). Use [UP] and [Down] to select a value between 1 and 512 (the display shows ‘d001’...
  • Page 28 Operation Operating mode ‘Slave’ This setting is only relevant if the unit is operated as slave device in a master / slave configura‐ tion and is not controlled via DMX. Press [Mode] repeatedly until the display shows ‘SLAv’ . Wait about 30 seconds until the display turns off. Then the settings have been applied. To return to the higher menu level without changes, press [Mode].
  • Page 29 Operation Constant unicoloured pattern A constant unicoloured pattern can only be activated if the unit is working in standalone mode or as master device in a master / slave combination. This setting is only relevant if the unit is not controlled via DMX. Press [Mode] repeatedly until the display shows ‘CL.xx’...

  • Page 30: Menu Overview

    Operation 7.3 Menu overview LED flower effect...

  • Page 31: Functions In 2-Channel Dmx Mode

    Operation 7.4 Functions in 2-channel DMX mode Channel Value Function LEDs off 1…9 Constant unicoloured red pattern 10…19 Constant unicoloured green pattern 20…29 Constant unicoloured blue pattern 30…39 Constant unicoloured white pattern 40…255 Sound-controlled automatic show Function depends on channel 1 setting Channel 1 = 0 No function Channel 1 = 1…39...

  • Page 32: Functions In 3-Channel Dmx Mode

    Operation Channel Value Function Channel 1 = 40…255 0…255 Sensitivity of the built-in microphone for sound-control 7.5 Functions in 3-channel DMX mode Channel Value Function Operating mode selection LEDs off 1…9 Preprogrammed automatic show no. 1 10…19 Preprogrammed automatic show no. 2 240…249 Preprogrammed automatic show no.
  • Page 33 Operation Channel Value Function 250…255 Sound-controlled automatic show Function depends on channel 1 setting Channel 1 = 0 No function Channel 1 = 1…249 0…255 Movement effect, increasing speed Channel 1 = 250…255 0…255 Sensitivity of the built-in microphone for sound-control Function depends on channel 1 setting Channel 1 = 0 No function...
  • Page 34 Operation Channel Value Function Channel 1 = 250…255 No function LED flower effect...

  • Page 35: Troubleshooting

    Troubleshooting Troubleshooting NOTICE! Possible data transmission errors For error-free operation make use of dedicated DMX cables and do not use ordi‐ nary microphone cables. Never connect the DMX output to audio devices such as mixers or amplifiers. In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting: MaTrixx TLB-20MK-II RGBW...
  • Page 36 Troubleshooting Symptom Remedy The unit does not work, no Check the mains connection and the fuse. light. No response to the DMX con‐ 1. Check the DMX ports and cables for proper connection. troller. 2. Check the address settings and the DMX polarity. 3.

  • Page 37: Cleaning

    Cleaning Cleaning Optical lenses Clean the exterior of accessible optical lenses periodically to optimise light output. The fre‐ quency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device. Clean with a soft cloth using normal glass cleaning products.

  • Page 38: Technical Specifications

    Technical specifications Technical specifications LEDs 192 LEDs (48 × white, 48 × red, 48 × green, 48 × blue) Dispersion angle 15 ° Number of DMX channels 2, 3 Operating voltage supply AC 230 V , 50 Hz Power consumption 30 W Dimensions (W ×...

  • Page 39: Protecting The Environment

    Protecting the environment Protecting the environment Disposal of the packaging mate‐ rial For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling.
  • Page 40 Notes LED flower effect...
  • Page 41 Notes MaTrixx TLB-20MK-II RGBW...
  • Page 42 Notes LED flower effect...
  • Page 44 Musikhaus Thomann e.K. · Treppendorf 30 · 96138 Burgebrach · Germany · www.thomann.de...

Table of Contents