Whirlpool WED9290FC HybridCare Installation Instructions Manual
Heat pump dryer
Hide thumbs
Also See for WED9290FC HybridCare:
- Installation instructions manual (44 pages) ,
- Use & care manual (36 pages)
Table of Contents
Advertisement
HybridCare™ Heat
Pump Dryer
Installation Instructions
Table of Contents
DRYER SAFETY......................................................................... 2
INSTALLATION REQUIREMENTS ........................................... 3
Tools and Parts ...................................................................... 3
LOCATION REQUIREMENTS ................................................... 4
DRAIN SYSTEM ......................................................................... 5
ELECTRICAL REQUIREMENTS - U.S.A. ONLY ..................... 6
INSTALL LEVELING LEGS ....................................................... 8
ELECTRICAL INSTALLATION - U.S.A. ONLY ........................ 8
Power Supply Cord Connection ........................................... 9
Direct Wire Connection ....................................................... 11
CONNECT OUTLET HOSE ..................................................... 14
LEVEL DRYER ......................................................................... 15
COMPLETE INSTALLATION CHECKLIST ............................ 16
DOOR REVERSAL (OPTIONAL) ............................................. 16
TROUBLESHOOTING ............................................................. 26
Para una version de estas instrucciones en español, visite www.Whirlpool.com or www.maytag.com
INSTALLATION NOTES
_________________________________
Date of purchase:
_______________________________
Date of installation:
________________________________________
Installer:
___________________________________
Model number:
___________________________________
Serial number:
W10777574B
W10777575B - SP
Sécheuse à pompe à
chaleur HybridCare™
Instructions d'installation
Table des matières
SÉCURITÉ DE LA SÉCHEUSE ............................................... 27
EXIGENCES D'INSTALLATION .............................................. 28
Outillage et pièces ............................................................... 28
EXIGENCES D'EMPLACEMENT ............................................ 29
SYSTÈME DE VIDANGE .......................................................... 30
SÉCHEUSE ÉLECTRIQUE RACCORDEMENT
À L'ALIMENTATION ÉLECTRIQUE -
CANADA SEULEMENT ........................................................... 31
INSTALLATION DES PIEDS DE NIVELLEMENT .................. 32
CONNEXION DU TUYAU DE SORTIE ................................... 32
RÉGLAGE DE L'APLOMB DE LA SÉCHEUSE ...................... 33
ACHEVER L'INSTALLATION LISTE DE VÉRIFICATION ...... 34
INVERSION DE LA PORTE (FACULTATIF) ........................... 34
DÉPANNAGE .................................... COUVERTURE ARRIÈRE
NOTES CONCERNANT L'INSTALLATION
_____________________________________
Date d'achat :
________________________________
Date d'installation :
______________________________________
Installateur :
________________________________
Numéro de modèle :
__________________________________
Numéro de série :
Advertisement
Table of Contents
Related Manuals for Whirlpool WED9290FC HybridCare
Summary of Contents for Whirlpool WED9290FC HybridCare
-
Page 1: Table Of Contents
INVERSION DE LA PORTE (FACULTATIF) ......34 COMPLETE INSTALLATION CHECKLIST ......16 DÉPANNAGE ........COUVERTURE ARRIÈRE DOOR REVERSAL (OPTIONAL) ..........16 TROUBLESHOOTING ............. 26 Para una version de estas instrucciones en español, visite www.Whirlpool.com or www.maytag.com INSTALLATION NOTES NOTES CONCERNANT L’INSTALLATION _________________________________ _____________________________________ Date of purchase: Date d’achat :... -
Page 2: Dryer Safety
Dryer Safety Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized. -
Page 3: Installation Requirements
Installation Requirements TOOLS AND PARTS Parts supplied: Gather the required tools and parts before starting installation. Tools needed: 6' (1829 mm) drain Leveling legs (4) hose with couplers Flat-blade screwdriver #2 Phillips screwdriver Cable ties (2) Wire stripper (direct wire Channel locks Parts package is located in dryer drum. -
Page 4: Location Requirements
Location Requirements Side view: Check code requirements. Some codes limit, or do not permit, installing dryer in garages, closets, mobile homes, or sleeping " min. quarters. Contact your local building inspector. (1314 mm) " min. (806 mm) You will need: A separate 30 amp circuit. -
Page 5: Drain System
Installation spacing for recessed area Drain System or closet installation All dimensions show recommended and minimum spacing allowed. Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need. Additional spacing should be considered for ease of ■... -
Page 6: Electrical Requirements - U.s.a. Only
Laundry tub drain system Electrical Connection To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. This dryer is manufactured ready to install with a 3-wire ■... -
Page 7: Electric Dryer Power Hookup - Canada Only
To supply the required 4-wire, single-phase, 120/240 volt, ■ 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. -
Page 8: Install Leveling Legs
Install Leveling Legs Electric Installation - U.S.A. Only Before you start: disconnect power. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to “Power Supply Cord Connection.” Prepare dryer for leveling legs Power supply cord 3-wire receptacle (NEMA Type 10-30R). -
Page 9: Power Supply Cord Connection
Power Supply Cord Connection Attach power supply cord to strain relief Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. - Page 10 Prepare to connect neutral ground Connect remaining wires wire and neutral wire Connect remaining wires under outer terminal block screws. Remove center terminal block screw (B). Remove neutral Tighten screws. Finally, reinsert tab of terminal block cover ground wire (E) from green external ground conductor screw (A). into slot of dryer rear panel.
-
Page 11: Direct Wire Connection
Direct Wire Connection Connect neutral wire Connect neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Tighten screw. Connect remaining wires Direct wire strain relief Attach direct wire strain relief Connect remaining wires under outer terminal block screws. Tighten screws. - Page 12 Prepare to connect neutral ground Attach direct wire cable to strain relief wire and neutral wire Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in Remove center terminal block screw (B). Remove neutral a horizontal position.
- Page 13 Connect remaining wires Connect neutral wire Place hooked end of neutral wire (white or center) (C) of direct wire cable under Place hooked ends of remaining direct wire cable wires under center terminal block screw (B), hook outer terminal block screws (hooks facing right). Squeeze facing right.
-
Page 14: Connect Outlet Hose
Connect Outlet Hose Connect neutral ground wire and neutral wire Attach hose Attach the goose-neck fitting of the provided 6 ft. (1829 mm) drain hose to the drain valve at the bottom of dryer back Connect neutral ground wire (E) and neutral wire (white or panel. -
Page 15: Level Dryer
Level Dryer Level dryer Place level here Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture-sensing system to operate correctly. If forward slope of dryer is greater than 1" (25 mm), water could run out from front Plug into a grounded 3 prong outlet of filter. -
Page 16: Complete Installation Checklist
Complete Installation Checklist Door Reversal (optional) The following instructions are for models with a round and ❑ Check that all parts are now installed. If there is an extra square-shaped doors. part, go back through steps to see what was skipped. Tools needed: ❑... - Page 17 Remove outer window assembly Move the door strike from trim ring ® Using a T25 screwdriver, remove the 2 screws securing the Fig. A door strike to the door frame of the dryer. Rotate the strike 180° and attach to the opposite side of dryer door frame as shown.
- Page 18 Rotate and reassemble outer window Reverse outer window assembly assembly to trim ring Bottom Handle of door Fig. A Notches Fig. A Fig. B With the edge with 2 notches at the top, align the notches on the outer window assembly with the tabs on the trim ring and lower into place as shown in figure A.
- Page 19 Remove hinge and latch Reinstall inner door assembly Latch Bottom of door Hinge Using a T25 ® screwdriver, remove the 3 screws securing the Position the door with the inside of the door facing up. Using latch plate and latch backing plate and the 5 screws holding a Phillips screwdriver, reinstall the 10 screws securing the the hinge assembly in place.
- Page 20 Reverse door swing curved glass – double handle Remove inner door from outer door Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. ®...
- Page 21 Reinstall door on dryer Reinstall hinge and latch on opposite sides ® Using a T25 screwdriver, remove the 4 screws on the dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place ®...
- Page 22 Remove outer window assembly Move the door strike from trim ring Fig. A ® Using a T25 screwdriver, remove the 2 screws securing the door strike to the door frame of the dryer. Rotate the strike 180° and attach to the opposite side of dryer door frame as shown.
- Page 23 Reverse outer window assembly Rotate and reassemble outer window assembly to trim ring Handle Bottom of door Notches Fig. A Fig. A Fig. B With the edge with 2 notches at the top, align the notches on the outer window assembly with the tabs on the trim ring and lower into place as shown in figure A.
- Page 24 Remove hinge and latch Reinstall inner door assembly Latch Bottom of door Hinge ® Using a T25 screwdriver, remove the 3 screws securing the Position the door with the inside of the door facing up. latch plate and latch backing plate and the 5 screws holding Reinstall the 10 screws securing the inner door to the the hinge assembly in place.
- Page 25 Reverse door swing flat glass – double handle Remove inner door from outer door Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Using a T25 ®...
-
Page 26: Troubleshooting
Reinstall hinge and latch on Reinstall door on dryer opposite sides Using a T25 ® screwdriver, remove the 4 screws on the dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place with Using a T25 ®...