Technical Data; Safety Instructions; Specified Conditions Of Use - Milwaukee PFH 26 Original Instructions Manual

TECHNICAL DATA

Rated input ..............................................................................
Output ......................................................................................
No-load speed .........................................................................
Speed under load max. ...........................................................
Rate of percussion under load max. ........................................
Impact energy per stroke according to EPTA-Procedure 05/2009 .....
Drilling capacity in concrete .....................................................
Drilling capacity in steel ...........................................................
Drilling capacity in wood ..........................................................
Light core cutter in bricks and limestone .................................
Chuck neck diameter ...............................................................
Weight according EPTA-Procedure 01/2003 ...........................
Noise Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .......................................
Sound power level (K = 3 dB(A)) ............................................
Wear ear protect !
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
Hammer-drilling in concrete: vibration emission value a
Uncertainty K = .......................................................................
Chiselling: vibration emission value a
Uncertainty K = .......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Wear ear protectors. Exposure to noise can cause hearing Do not use diamond core drills on hammer mode.
loss.
Wear ear protection when impact drilling. Exposure to noise
can cause hearing loss. Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Use auxiliary handles supplied with the tool. Loss of control
Hold power tool by insulated gripping surfaces, when
can cause personal injury.
performing an operation where the cutting accessory
Hold power tool by insulated gripping surfaces, when
may contact hidden wiring or its own cord. Cutting
performing an operation where the cutting accessory may
accessory contacting a „live" wire may make exposed metal
contact hidden wiring or its own cord. Cutting accessory
parts of the power tool „live" and could give the operator an
contacting a „live" wire may make exposed metal parts of the
electric shock.
power tool „live" and could give the operator an electric shock.
Appliances used at many different locations including open
Appliances used at many different locations including open air
air must be connected via a current surge preventing switch.
should be connected via a residual current device (FI, RCD,
Always wear goggles when using the machine. It is
PRCD) of 30mA or less.
recommended to wear gloves, sturdy non slipping shoes
Always wear eye and hearing protection when using the machine.
and apron.
It is recommended to wear gloves and sturdy non slipping shoes.
Sawdust and splinters must not be removed while the
Sawdust and splinters must not be removed while the machine is
machine is running.
running.
Always disconnect the plug from the socket before carrying
Before doing any maintenance work on the machine, pull the plug
out any work on the machine.
out of the socket.
16 ENGLISH
289 776 - PH26.indd 16 289 776 - PH26.indd 16
Rotary Hammer
:
h
....................................
h
PFH 26
.........................725 W ...........................725 W
.........................365 W ...........................365 W
.......................1500 min
.......................1250 min
.......................4500 min
..........................2,4 J ..............................2,4 J
...........................26 mm ..........................26 mm
...........................13 mm ..........................13 mm
...........................30 mm ..........................30 mm
...........................50 mm ..........................50 mm
...........................43 mm ..........................43 mm
..........................2,4 kg ............................2,4 kg
...........................92 dB (A) ......................92 dB (A)
.........................103 dB (A) ....................103 dB (A)
....... ........................13,5 m/s
..........................1,5 m/s
..............................- m/s
..............................- m/s
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Under the effect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.

SPECIFIED CONDITIONS OF USE

PFH 26: The rotary pneumatic hammer can be used for
hammer drilling and drilling in wood, metal as well as plastic.
PH 26: The rotary pneumatic hammer can be used for
hammer drilling, chiselling in stone and concrete and drilling
in wood, metal as well as plastic.
Do not use this product in any other way as stated for
normal use.
PH 26
-1 .....................1500 min -1
.....................1250 min
-1 -1
-1 .....................4500 min -1
.......................13,5 m/s
2 2
.........................1,5 m/s
2 2
....................... 11,2 m/s
2 2
2 .........................1,5 m/s 2
14.11.2011 14:52:41 14.11.2011 14:52:41