Kramer VS-1616D-MD User Manual
  1. Manuals
  2. Brands
  3. Kramer Manuals
  4. Matrix Switcher
  5. VS-1616D-MD
  6. User manual

Kramer VS-1616D-MD User Manual

16x16 digital matrix switcher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
K R A ME R E LE CT R O N IC S L TD .
USER MANUAL
MODEL:
VS-1616D-MD
16x16 Digital Matrix Switcher
P/N: 2900-300434 Rev 2

Advertisement

Table of Contents
loading

Related Manuals for Kramer VS-1616D-MD

Summary of Contents for Kramer VS-1616D-MD

  • Page 1 K R A ME R E LE CT R O N IC S L TD . USER MANUAL MODEL: VS-1616D-MD 16x16 Digital Matrix Switcher P/N: 2900-300434 Rev 2...

  • Page 4: Table Of Contents

    Medical Electrical Equipment (IEC 60601-1) Overview About Fast Switching About HDBaseT™ Technology About the Power Connect™ Feature Defining the VS-1616D-MD 16x16 Digital Matrix Switcher Installing in a Rack Connecting the VS-1616D-MD Card Limitations Port Numbering Serial Data on DGKat Plus RS-232 Cards...
  • Page 5 Communication Protocol 2000 Figures Figure 1: VS-1616D-MD Front Panel Numeric Keypad Figure 2: VS-1616D-MD 16x16 Digital Matrix Switcher Front Panel Figure 3: VS-1616D-MD 16x16 Digital Matrix Switcher Rear Panel Figure 4: Connecting the VS-1616D-MD 16x16 Digital Matrix Switcher Figure 5: Sample Port Numbering...

  • Page 6: Introduction

    Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis. In recent years, we have redesigned and upgraded most of our...
  • Page 7 Test card plus analog audio embedding/de-embedding   VGA plus analog audio Note: The HDMI over fiber optic with 670 module cards are fully compatible with the Kramer 670T/670R and 671T/671R HDMI/DVI transmitters and receivers for non-HDCP content. VS-1616D-MD - Introduction...

  • Page 8: Getting Started

    Avoid interference from neighboring electrical appliances that may adversely influence signal quality  Position your Kramer VS-1616D-MD away from moisture, excessive sunlight and dust This equipment is to be used only inside a building. It may be connected only to other equipment that is installed inside a building.

  • Page 9: Safety Instructions

    Safety Instructions Warning: No operator serviceable parts inside the unit Warning: Use only the Kramer Electronics input power wall adapter that is provided with the unit. Warning: Disconnect the power and unplug the unit from the wall before installing Warning:...

  • Page 10: Recycling Kramer Products

    Kramer Electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.

  • Page 11: Overview

    Overview The Kramer VS-1616D-MD is a high performance matrix switcher chassis that supports up to 16 x 16 ports. It features a very high bandwidth of up to 3.2Gbps (for the chassis only, effective bandwidth of the system depends on the I/O cards) that ensures transparent performance even in the most critical applications.

  • Page 12: About Fast Switching

    A 40 character by 2 line LCD that shows the operational status or the configuration menu You can operate the VS-1616D-MD via the front panel buttons or remotely via:  RS-232 serial commands transmitted by a touch screen system, PC or other serial controller ...

  • Page 13: About Hdbaset™ Technology

    Depending on the display device in use, the VS-1616D-MD allows for fast switching (minor reset and the connection kept alive) and extra fast switching (no reset and the connection kept alive), see Section 8.2.4. Using the fast and extra fast switching modes allows for fraction-of-a-second switching times when using high performance display devices or when using a scaler on the video output.

  • Page 14: Defining The Vs-1616D-Md 16X16 Digital Matrix Switcher

    32) 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Numeric keypad, 1 to 0 ► (Forward) Press to shift the sliding window to the left VS-1616D-MD - Defining the VS-1616D-MD 16x16 Digital Matrix Switcher...

  • Page 15: Figure 2: Vs-1616D-Md 16X16 Digital Matrix Switcher Front Panel

    Figure 2: VS-1616D-MD 16x16 Digital Matrix Switcher Front Panel...
  • Page 16 8). Press again to enter the configuration menu (see Section 8.2). When in a Menu, press to cycle through the menu items LOCK Button Press and hold for approximately 2 sec to lock/unlock the front panel buttons (see Section 7.5) VS-1616D-MD -...

  • Page 17: Figure 3: Vs-1616D-Md 16X16 Digital Matrix Switcher Rear Panel

    Figure 3 shows DVI cards installed as an example. Figure 3: VS-1616D-MD 16x16 Digital Matrix Switcher Rear Panel...
  • Page 18 PATTERN Button Press the button repeatedly to change the video pattern generated by the Test module (see Section 10.3) Test Module Output Connect to one of the relevant video inputs to aid in troubleshooting (see Section 10.4) Connector VS-1616D-MD -...

  • Page 19: Installing In A Rack

    Installing in a Rack This section provides instructions for rack mounting the unit. VS-1616D-MD - Installing in a Rack...

  • Page 20: Connecting The Vs-1616D-Md

    Always switch off the power to all devices before connecting them to your VS-1616D-MD. After connecting your VS-1616D-MD, connect its power and then switch on the power to each device. Figure 4: Connecting the VS-1616D-MD 16x16 Digital Matrix Switcher VS-1616D-MD - Connecting the VS-1616D-MD...

  • Page 21: Card Limitations

    5. If necessary, review and set the system configuration using the Menu (see Section Note: Given an input signal that is HDCP encoded, the VS-1616D-MD outputs a signal only if the output port supports HDCP, (for example, HDMI input and DVI with HDCP output).

  • Page 22: Port Numbering

    Each DVI dual link card provides two physical ports which causes the loss of two numbers in the numbering sequence of that card only. A sample numbering is shown in Figure Figure 5: Sample Port Numbering VS-1616D-MD - Connecting the VS-1616D-MD...
  • Page 23 Note: AV data flow is: source > VS-1616D-MD > display. EDID information flow is: display > VS-1616D-MD > source, which means that the EDID input is the display side and the EDID output is the AV source side. This is the reverse of the AV data flow direction.

  • Page 24: Serial Data On Dgkat Plus Rs-232 Cards

    Serial data present on the RS-232 port of a DGKat output card are not transmitted via the switcher. This data are transmitted over the TP cable of the same output card. Figure 7: DGKat Card Serial Data Transmission VS-1616D-MD - Connecting the VS-1616D-MD...

  • Page 25: Connecting To The Vs-1616D-Md Via

    9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 need to be connected) to the RS-232 9-pin D-sub port on your PC Connecting to the VS-1616D-MD via Ethernet You can connect to the VS-1616D-MD via Ethernet using either of the following methods: ...

  • Page 26: Figure 8: Local Area Connection Properties Window

    4. Highlight either Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) depending on the requirements of your IT system. 5. Click Properties. The Internet Protocol Properties window relevant to your IT system appears as shown in Figure 9 Figure VS-1616D-MD - Connecting the VS-1616D-MD...

  • Page 27: Figure 9: Internet Protocol Version 4 Properties Window

    Figure 9: Internet Protocol Version 4 Properties Window Figure 10: Internet Protocol Version 6 Properties Window VS-1616D-MD - Connecting the VS-1616D-MD...

  • Page 28: Figure 11: Internet Protocol Properties Window

    6.5.2 Connecting the Ethernet Port via a Network Hub or Switch You can connect the Ethernet port of the VS-1616D-MD to the Ethernet port on a network hub or using a straight-through cable with RJ-45 connectors. VS-1616D-MD - Connecting the VS-1616D-MD...

  • Page 29: Operating Your Video Matrix Switcher

    The text in the LCD Display may vary (according to machine settings) Figure 12: Default Startup Status Display Sequence The front panel of the VS-1616D-MD includes a numeric keypad within the selector buttons area. This keypad lets you enter both the output and input...

  • Page 30: Using The Selector Buttons

    Using the Selector Buttons For numbers between 1 and 9, the VS-1616D-MD can handle two digit numbers as well as single digit numbers. When entering a single digit number (for example 5), you can either press 0 followed by 5, or 5 followed by ENT.

  • Page 31: Confirming Actions

    Confirm modes. A flashing TAKE button indicates that an action is currently pending confirmation. 1. Press TAKE to switch between the At Once mode and the Confirm mode. The TAKE button lights and actions now require user confirmation. VS-1616D-MD - Operating Your Video Matrix Switcher...

  • Page 32: Switching Actions

    06 07 08 09 10 11 12 13 In__ => Out 12 The left-hand side of the display shows a section of the output/input display automatically sliding the content to include output 12. VS-1616D-MD - Operating Your Video Matrix Switcher...
  • Page 33 3. After entering all output/input combinations, press the flashing TAKE button to confirm the actions. The inputs switch to the respective outputs as shown on the LCD display and the TAKE LED is lit. VS-1616D-MD - Operating Your Video Matrix Switcher...
  • Page 34 Note: This is not the setup that is loaded when the unit is turned on. When the unit is turned on, the setup that was last used before the unit was turned off is loaded. VS-1616D-MD - Operating Your Video Matrix Switcher...

  • Page 35: Locking The Front Panel Buttons

    Locking the Front Panel Buttons You can lock the VS-1616D-MD to prevent tampering with the unit or prevent the settings from being changed accidentally via the front panel buttons. You can still remotely operate via RS-232 or Ethernet even when the front panel is locked To lock the front panel buttons: ...

  • Page 36: Using The Configuration Menus

    Using the Configuration Menus The configuration menus let you configure the VS-1616D-MD to best suit your needs. There are two configuration menus:  Setup Menu—those that are accessed on a regular basis (for example, storing setups and setting the delay), see Section 8.1...

  • Page 37: Using The Setup Menu

    This option switches one input to all outputs. To switch one input to all outputs: 1. Press MENU. The Setup Menu options are displayed. 2. Press 1 (ALL) on the numeric keypad (see Figure The following is displayed: in__ => ALL VS-1616D-MD - Using the Configuration Menus...
  • Page 38 More than eight EDID assignments must be assigned in separate batches of eight. Each input on the VS-1616D-MD has a factory default EDID loaded (see Section 16). The EDID for each input can be changed independently via the menu (described below).
  • Page 39 5. Repeat Step 4 for up to eight inputs. 6. Press TAKE. The EDID is stored and passed through to the input. The display reverts to the output/input display. 7. Repeat the above steps for the next batch of eight EDID assignments. VS-1616D-MD - Using the Configuration Menus...
  • Page 40 3. Using the numeric keys, enter the output (in this example, 03). The following is displayed: 01 02 03 04 05 06 07 08 DLY__ =>out03 4. Using the numeric keys, enter the number of delay units. VS-1616D-MD - Using the Configuration Menus...
  • Page 41 Setup Menu—6: recall setup XX, Recalling a Preset This option recalls a stored configuration from a preset (1 to 59). To recall a stored configuration: 1. Press MENU. The Setup Menu options are displayed. VS-1616D-MD - Using the Configuration Menus...

  • Page 42: Using The Config Menu

    Interface configuration (Section 8.2.5)  Interface Reply configuration (Section 8.2.6)  Protocol configuration (Section 8.2.7)  Storing the default setup (Section 8.2.8)  Resetting the VS-1616D-MD (Section 8.2.9)  Firmware revision display (Section 8.2.10) VS-1616D-MD - Using the Configuration Menus...
  • Page 43 This option displays a list of inputs and indicates on which of them signals have been detected. To display a list of inputs that have detected signals: 1. Press MENU twice. The following message is displayed: start configuration menu MENU to view setup ENT to change them VS-1616D-MD - Using the Configuration Menus...
  • Page 44 0 indicates that there are modifiable parameters for the associated port. 3. Press TAKE to enter the list of ports. The cursor flashes on a selected port. 4. Select the required port to modify using the left and right arrow buttons. VS-1616D-MD - Using the Configuration Menus...
  • Page 45 Note: Not all options are displayed for every menu selection. Some parameters depend on the specific selection of other parameters. Note: The volume control provides only attenuation, no gain. Hence, setting volume to 100% provides no attenuation. VS-1616D-MD - Using the Configuration Menus...
  • Page 46 Volume Sets the audio output volume (0–70) Audio Balance Sets the audio output channel balance (0–100) Audio Bass Sets the audio output bass level (0–15) Audio Treble Sets the audio output treble level (0–15) VS-1616D-MD - Using the Configuration Menus...
  • Page 47 @60Hz @36bpp; On for distances of up to 150m at 1080p @60Hz @24bpp *0:ON, 1:OFF Note: The range can be increased by approximately 30% by using Kramer high quality cables, such as, the BC-HDKat6a HDMI plus Analog Audio Input Card Parameter Description...
  • Page 48 Auto: Audio signal selection is controlled by the presence or Auto absence of a plug in the 3.5mm mini jack. AUD-Embedded: HDMI audio is selected. AUD-Ex-Digital: S/PDIF audio is selected (only works on HDMI plus S/PDIF card) VS-1616D-MD - Using the Configuration Menus...
  • Page 49 Sets the audio output channel balance (0–100) Audio Bass Sets the audio output bass level (0–15) Audio Treble Sets the audio output treble level (0–15) Audio Mute MUTE: Mutes the audio input Non- MUTE Non-MUTE: Unmutes the audio input VS-1616D-MD - Using the Configuration Menus...
  • Page 50 In order to revert to auto pre-defined parameters, you should either reset to factory setting with the relevant source connected or connect a different source. VS-1616D-MD - Using the Configuration Menus...
  • Page 51 To set parameters for a port: 1. Press MENU twice. The following message is displayed: start configuration menu MENU to view setup ENT to change them VS-1616D-MD - Using the Configuration Menus...
  • Page 52 11. Do one of the following:  Press BREAKAWAY to exit the Config Menu  Wait approximately 15 seconds for the operation to time out  Press MENU to exit to the parameter list VS-1616D-MD - Using the Configuration Menus...
  • Page 53 Switch Speed When switching between different sources the switching time can Normal be reduced by setting the fast switch level (Ex-fast Switch, Fast Switch Switch or Normal Switch) by reducing color depth to 8-bits VS-1616D-MD - Using the Configuration Menus...
  • Page 54 Switch Speed When switching between different sources the switching time can Normal be reduced by setting the fast switch level (Ex-fast Switch, Fast Switch Switch or Normal Switch) by reducing color depth to 8-bits VS-1616D-MD - Using the Configuration Menus...
  • Page 55 Enables range extender. Off for distances of up to 100m at 1080p @60Hz @36bpp; On for distances of up to 150m at 1080p @60Hz @24bpp *0:ON, 1:OFF Note: Using Kramer high quality cables such as the BC-HDKat6a can increase the range by approximately 30% VS-1616D-MD - Using the Configuration Menus...
  • Page 56 (Fast Switch or Switch Normal Switch) by reducing color depth to 8-bits Reset Output Re-power: power cycle the port Re-power Factory default: perform a factory reset of the port to default values VS-1616D-MD - Using the Configuration Menus...
  • Page 57 Switch Speed When switching between different sources the switching time can Normal be reduced by setting the fast switch level (Ex-fast Switch, Fast Switch Switch or Normal Switch) by reducing color depth to 8-bits VS-1616D-MD - Using the Configuration Menus...
  • Page 58 7D-03 FW VER: 4.0_0006 SPEC VER:0107 21200025C30 Note: To ensure a stable output signal using either WUXGA (1920X1200) or UXGA (1600X1200), set the output to 8 bit color depth in the Deep Color menu. VS-1616D-MD - Using the Configuration Menus...
  • Page 59 Sets the audio output channel balance (0–100) Audio Bass Sets the audio output bass level (0–15) Audio Treble Sets the audio output treble level (0–15) Audio Mono OFF—Analog output is stereo MIX—Analog output is mono VS-1616D-MD - Using the Configuration Menus...
  • Page 60 Non-MUTE: unmutes the audio input Note: When set to Mute, any change to the audio parameters automatically sets this to unmute OUT_HSYNC_ Sets the H_SYNC invert. INVERT (0, 1) OUT_VSYNC_ Sets the V_SYNC invert. INVERT (0, 1) VS-1616D-MD - Using the Configuration Menus...
  • Page 61 Setting Reply to off causes all interfaces that are set to on to accept and execute commands, but not to reply. VS-1616D-MD - Using the Configuration Menus...
  • Page 62 After a few seconds the next option on the Config Menu is displayed. 8.2.7 Config Menu—Protocol Configuration The VS-1616D-MD supports Kramer Protocol 2000 and Protocol 3000. To switch from Protocol 3000 (default) to Protocol 2000: 1. Press MENU twice. The following message is displayed:...
  • Page 63 2. Press MENU until the following is displayed: store DEFAULT setup press ENTER to store 3. Press ENT to store the current configuration as the default configuration. The following is displayed: current matrix stage is OKAY? press TAKE to confirm VS-1616D-MD - Using the Configuration Menus...
  • Page 64 Selecting option 2 to perform a factory default reset Warning: clears all setups, options and configuration 5. Press TAKE and wait a few seconds. The following is displayed: Are you Absolutely sure !!! Once more TAKE to confirm VS-1616D-MD - Using the Configuration Menus...
  • Page 65 2. Press MENU until the following is displayed: Main Firmware Version: Front Firmware Version: 1.0 3. Either press BREAKAWAY to exit the Config Menu or wait approximately 15 seconds for the operation to time out. VS-1616D-MD - Using the Configuration Menus...

  • Page 66: Configuring The Number Of Installed Input And Output Ports

    Output Ports After installing or removing a module you need to set the number of input and output ports so that the VS-1616D-MD recognizes the new configuration. Refer to Section 6.2 for an explanation of port numbering before setting the number of input and output ports.

  • Page 67: Installing And Using The Test Module To Troubleshoot Video Problems

    Installing and Using the Test Module to Troubleshoot Video Problems The VS-1616D-MD includes a test module which acts as a signal generator and can be used to diagnose video/audio issues in an operating environment. The test module must be installed in the configuration before it can be used. When installing the test module, the number of configured inputs and outputs must be increased by one.

  • Page 68: Setting The Resolution Of The Generated Video

    Available HD Resolutions for Generated Video (Jumper on, default) DIP-switch Position Resolution 480p 720p 1080i 1080p Figure 14 shows the Resolution DIP-switch with both switches off (up, default, 480p). Figure 14: Resolution DIP-switch VS-1616D-MD - Installing and Using the Test Module to Troubleshoot Video Problems...

  • Page 69: Setting The Pattern Of The Generated Video

     The test module is installed and configured (see Section 10.1)  17 configured inputs and 17 configured outputs (see Section Figure 15: Signal Paths for Isolating Problems VS-1616D-MD - Installing and Using the Test Module to Troubleshoot Video Problems...
  • Page 70 To test the input and output signal path to the projector: 1. Configure Input 17 to Output 33 (see Section 7.4). 2. Connect Output 17 to Input 1. 3. Configure Input 1 to Output 1. VS-1616D-MD - Installing and Using the Test Module to Troubleshoot Video Problems...
  • Page 71 5. Set the generated video resolution (see Section 10.2). 6. Set the pattern for the generated video (see Section 10.3). 7. Verify that the projector output is as expected. VS-1616D-MD - Installing and Using the Test Module to Troubleshoot Video Problems...

  • Page 72: Hardware Installation Instructions

    Hardware Installation Instructions 11.1 I/O Card Installation The VS-1616D-MD I/O cards mount in one of the 16 slots on the rear of the VS-1616D-MD chassis. Slots are numbered from left to right and must be filled consecutively from left to right, without leaving empty slots.

  • Page 73: Figure 17: Card Handles

    To install an I/O card as shown in Figure 1. Power off the VS-1616D-MD and all devices connected to it. 2. Using a Phillips screwdriver, loosen the screws at the top and bottom of the blanking plate. 3. Remove the blanking plate from the slot and store it for possible future use.
  • Page 74 9. Power on the VS-1616D-MD and follow the procedure to configure the new card (see Section 10. Power on the peripheral devices. VS-1616D-MD - Hardware Installation Instructions...

  • Page 75: Upgrading The Vs-1616D-Md Firmware

    Upgrading the VS-1616D-MD Firmware Upgrading the firmware on the VS-1616D-MD can only be done by authorized service personnel. VS-1616D-MD - Upgrading the VS-1616D-MD Firmware...

  • Page 76: Technical Specifications

    REGULATORY COMPLIANCE: WEEE INCLUDED ACCESSORIES: Power cord, Infrared remote control transmitter Specifications are subject to change without notice at http://www.kramerelectronics.com The following table lists the technical specifications of the cards that are compatible with the VS-1616D-MD chassis. VS-1616D-MD - Technical Specifications...
  • Page 77 2 VGA on 15-pin HD connectors 1 Multi-mode glass fiber cables with LC connections must be used, such as the Kramer C-4LC/4LC 2 Multi-mode glass fiber cables with SC connections must be used, such as the Kramer C-SC/SC/OM3 3 Twisted pair cables with RJ-45 connections must be used, such as the Kramer BC-DGKat623...
  • Page 78 Kramer C-SC/SC/OM3. For the DGKat plus RS-232, shielded TP pair cables with RJ-45 connections must be used, such as the Kramer BC-DGKat623 or BC-DGKat7a23. For the HDBaseT, twisted pair cables with RJ-45 connections must be used, such as the Kramer BC-HDKat6a.

  • Page 79: Default Communication Parameters

    Command Format: P2000, to switch Output 1 to Input 1: 0x01, 0x81, 0x81, 0x81 P3000, to switch Output 1 to Input 4: #AV 4>1 Ethernet IP Address 192.168.1.39 TCP Port # 5000 UDP Port # 50000 VS-1616D-MD - Default Communication Parameters...

  • Page 80: Label Information

    60Hz at 1.5A Fuse—Rating 250V at 3.15A time lag Important information included in the User Manual Complies with the WEEE Restriction of Hazardous Substances Directive of the EU of 2006 for devices placed on the market after 2005 VS-1616D-MD - Label Information...

  • Page 81: Factory Default Edid

    1280 x 960p at 60Hz - VESA STD 1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD VS-1616D-MD - Factory Default EDID...

  • Page 82: Hdcp Input Card

    1280 x 800p at 60Hz - VESA STD 1440 x 900p at 60Hz - VESA STD 1280 x 960p at 60Hz - VESA STD 1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD VS-1616D-MD - Factory Default EDID...
  • Page 83 Front left/right center.. No Rear left/right center... No Rear LFE....No CE vendor specific data (VSDB) IEEE registration number. 0x000C03 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,18,14,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,81,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,02,3A,80,18,71,38,2D,40,58,2C, 45,00,C4,8E,21,00,00,1E,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,33,32,48,44,43,50,0A,20,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,01,F9, 02,03,1A,41,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,C0 VS-1616D-MD - Factory Default EDID...

  • Page 84: Hdmi Input Card

    1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number..3 IT underscan..... Not supported Basic audio....Supported VS-1616D-MD - Factory Default EDID...
  • Page 85 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,10,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,0E,1F,00,80,51,00,1E,30,40,80, 37,00,6F,13,11,00,00,1E,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,31,36,48,44,43,50,0A,20,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,01,4D, 02,03,1A,41,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,C0 Model name....VS-16HDCP Manufacturer..... KRM Plug and Play ID..KRM0200 Serial number.... 1 Manufacture date..2010, ISO week 24 VS-1616D-MD - Factory Default EDID...

  • Page 86: Hdmi Plus Audio Input Card

    1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number..3 IT underscan..... Not supported VS-1616D-MD - Factory Default EDID...
  • Page 87 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Report information Date generated... 11/10/2013 Software revision..2.60.0.972 Data source....Real-time 0x0051 Operating system..5.1.2600.2.Service Pack 3 Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,16,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,01,1D,00,72,51,D0,1A,20,6E,28, 55,00,6F,13,11,00,00,1E,02,3A,80,18,71,38,2D,40,58,2C,45,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,31,36,48,2B,41,55,44,0A,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,01,80, 02,03,1A,71,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,90 VS-1616D-MD - Factory Default EDID...

  • Page 88: Dvi Dual Channel Input Card

    1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number..3 IT underscan..... Not supported VS-1616D-MD - Factory Default EDID...
  • Page 89 Front left/right center.. No Rear left/right center... No Rear LFE....No CE vendor specific data (VSDB) IEEE registration number. 0x000C03 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,10,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,64,19,00,40,41,00,26,30,18,88, 36,00,6F,13,11,00,00,1E,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,31,36,44,55,41,4C,0A,20,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,00,60, 02,03,1A,41,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,C0 VS-1616D-MD - Factory Default EDID...

  • Page 90: Dgkat Input Card

    1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number..3 IT underscan..... Not supported VS-1616D-MD - Factory Default EDID...
  • Page 91 Front left/right center.. No Rear left/right center... No Rear LFE....No CE vendor specific data (VSDB) IEEE registration number. 0x000C03 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,10,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,0E,1F,00,80,51,00,1E,30,40,80, 37,00,6F,13,11,00,00,1E,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,31,36,68,43,61,74,35,65,0A,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,01,92, 02,03,1A,41,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,C0 VS-1616D-MD - Factory Default EDID...

  • Page 92: Hdbaset Input Card

    1280 x 1024p at 60Hz - VESA STD 1400 x 1050p at 60Hz - VESA STD 1680 x 1050p at 60Hz - VESA STD 1600 x 1200p at 60Hz - VESA STD EIA/CEA-861 Information Revision number..3 IT underscan..... Not supported VS-1616D-MD - Factory Default EDID...
  • Page 93 IEEE registration number. 0x000C03 CEC physical address..1.0.0.0 Maximum TMDS clock..165MHz Report information Date generated... 14/07/2013 Software revision..2.60.0.972 Data source....File Operating system..6.1.7601.2.Service Pack 1 Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,00,02,01,00,00,00,0C,10,01,03,81,46,27,78,0A,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,8B,C0,81,00,95,00,81,40,81,80,90,40,B3,00,A9,40,01,1D,00,72,51,D0,1A,20,6E,28, 55,00,7E,88,42,00,00,1A,28,3C,80,A0,70,B0,23,40,30,20,36,00,06,44,21,00,00,1A,00,00,00,FC,00,56, 53,2D,31,36,48,44,42,53,54,0A,20,20,00,00,00,FD,00,32,55,1F,5E,11,00,0A,20,20,20,20,20,20,01,D3, 02,03,1A,71,47,11,13,05,14,84,10,1F,23,0A,06,04,83,05,00,00,65,03,0C,00,10,00,8C,0A,D0,8A,20,E0, 2D,10,10,3E,96,00,58,C2,21,00,00,18,01,1D,80,18,71,1C,16,20,58,2C,25,00,C4,8E,21,00,00,9E,01,1D, 80,D0,72,1C,16,20,10,2C,25,80,C4,8E,21,00,00,9E,01,1D,00,72,51,D0,1E,20,6E,28,55,00,C4,8E,21,00, 00,1E,01,1D,00,BC,52,D0,1E,20,B8,28,55,40,C4,8E,21,00,00,1E,00,00,00,00,00,00,00,00,00,00,00,90 VS-1616D-MD - Factory Default EDID...

  • Page 94: Vga Input Card

    1152 x 864p at 75Hz - VESA STD 1280 x 1024p at 75Hz - VESA STD 1280 x 960p at 60Hz - VESA STD 1280 x 1024p at 60Hz - VESA STD 1360 x 765p at 60Hz - VESA STD VS-1616D-MD - Factory Default EDID...
  • Page 95 Report information Date generated... 14/07/2013 Software revision..2.60.0.972 Data source....File Operating system..6.1.7601.2.Service Pack 1 Raw data 00,FF,FF,FF,FF,FF,FF,00,2E,4D,0B,04,A0,42,00,00,30,15,01,03,00,46,27,78,0B,D5,7C,A3,57,49,9C,25, 11,48,4B,FF,FF,80,31,40,45,40,61,40,71,4F,81,8F,81,40,81,80,8B,C0,D6,09,80,A0,20,E0,2D,10,10,60, A2,00,04,03,00,00,00,18,02,3A,80,18,71,38,2D,40,58,2C,45,00,10,09,00,00,00,1E,00,00,00,FC,00,56, 47,41,2D,49,4E,32,2D,46,31,36,0A,20,48,3F,40,30,62,B0,32,40,40,C0,13,00,6F,13,11,00,00,1E,00,0C VS-1616D-MD - Factory Default EDID...

  • Page 96: Communication Protocol 3000

    Communication Protocol 3000 The VS-1616D-MD can be operated using serial commands from a PC, remote controller or touch screen using the Kramer Protocol 3000. This section describes the:  Kramer Protocol 3000 syntax (see Section 17.1)  Kramer Protocol 3000 commands (see Section 17.2)
  • Page 97 CRLF – For device messages; carriage return (ASCII 13) + line-feed (ASCII 10) Command chain separator character When a message string contains more than one command, a pipe ( '|' ) character separates each command. Spaces between parameters or command terms are ignored. VS-1616D-MD - Communication Protocol 3000...
  • Page 98 You can directly enter all commands using a terminal with ASCII communications software, such as HyperTerminal, Hercules, etc. Connect the terminal to the serial or Ethernet port on the Kramer device. To enter CR press the Enter key. ( LF is also sent but is ignored by command parser).

  • Page 99: Table Of Protocol 3000 Commands

    RESET Reset device SIGNAL Valid / Invalid input Read device serial number VERSION? Read device firmware version Switch Video only Note: Not every command listed by the Help command is relevant to every matrix configuration. VS-1616D-MD - Communication Protocol 3000...

  • Page 100: Communication Protocol 2000

    The following table lists the Protocol 2000 hex codes for switching inputs 1 through 16 to outputs 1 through 16. IN 1 IN 2 IN 3 IN 4 IN 5 IN 6 IN 7 IN 8 IN 9 IN 10 IN 11 IN 12 IN 13 VS-1616D-MD - Communication Protocol 2000...
  • Page 101 IN 14 IN 15 IN 16 VS-1616D-MD - Communication Protocol 2000...
  • Page 103 For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.com SAFETY WARNING...

Table of Contents