Add Fuel; Start The Engine; Electric Start; Rewind Start - Snapper 1696219-00 Operator's Manual

Operation

Add Fuel

˻ ·Äº ¿ÊÉ Ì·ÆÅÈÉ ·È» »ÎÊȻûÂÏ ·Ã÷¸Â»
and explosive.
Fire or explosion can cause severe burns or
death.
When Adding Fuel
ËÈÄ »Ä½¿Ä» ż¼ ·Äº Â»Ê »Ä½¿Ä» ¹ÅÅ ·Ê »·ÉÊ Ã¿ÄËÊ»É ¸»¼ÅÈ»
removing the fuel cap.
¿Â ¼Ë»Â Ê·ÄÁ ÅËʺÅÅÈÉ ÅÈ ¿Ä ͻ ̻Äʿ·ʻº ·È»·
Å ÄÅÊ Å̻ȼ¿Â ¼Ë»Â Ê·ÄÁ Å ·ÂÂÅÍ ¼ÅÈ »ÎÆ·ÄÉ¿ÅÄ Å¼ ʾ» ¼Ë»Â ºÅ
not fill above the bottom of the fuel tank neck.
»»Æ ¼Ë»Â ·Í·Ï ¼ÈÅà ÉÆ·ÈÁÉ ÅÆ»Ä ¼Â·Ã»É Æ¿ÂÅÊ Â¿½¾ÊÉ ¾»·Ê
and other ignition sources.
¾»¹Á ¼Ë»Â Â¿Ä»É Ê·ÄÁ ¹·Æ ·Äº ¼¿ÊÊ¿Ä½É ¼È»ÇË»ÄÊÂÏ ¼ÅÈ ¹È·¹ÁÉ
or leaks. Replace if necessary.
¼ ¼Ë»Â ÉÆ¿ÂÂÉ Í·¿Ê ËÄÊ¿Â ¿Ê »Ì·ÆÅÈ·Ê»É ¸»¼ÅÈ» ÉÊ·ÈʿĽ »Ä½¿Ä»
1. Clean the fuel cap area of dirt and debris. Remove the
fuel cap (A, Figure 4).
2. Fill the fuel tank with fuel. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
3. Reinstall the fuel cap.

Start the Engine

The electric starter is equipped with a three-
wire power cord and plug designed to operate
on AC household current. The power cord must
be properly grounded at all times to avoid the
possibility of electric shock.
If your house does not have a three-wire grounded system, do
not use this electric starter. Contact a licensed electrician for
installation of a three-wire grounded system.
ÂÍ·ÏÉ ¹ÅÄÄ»¹Ê ʾ» ÆÅÍ»È ¹ÅȺ ÈÉÊ ÊŠʾ» ÉͿʹ¾ ¸ÅÎ ÂŹ·Ê»º
on the equipment and then plug the other end into a grounded
receptacle. After starting, disconnect the power cord from the
½ÈÅËĺ»º È»¹»ÆÊ·¹Â» ÈÉÊ
Be sure that engine oil is at FULL mark on the oil fill cap/
dipstick. The snowthrower engine is equipped with an AC
electric starter and recoil starter. Before starting the engine,
be certain that you have read the following information.
14
WARNING
WARNING
WARNING
If engine floods, set the choke to the OPEN/RUN position
and crank until the engine starts.
Start the engine as follows:
1. Check the oil level. See the Check/Add Oil section.
2. Make sure auger control is disengaged.
3. Insert the ON/OFF key (A, Figure 5) and turn to the ON
position or insert the Push/Pull key, if equipped.
4. Turn the choke knob (B) fully clockwise if engine is cold.
NOTE: Do not use the choke to start a warm engine.
5. Push the primer button (C) two times.
NOTE: Do not use the primer to start a warm engine.
Rapid retraction of the starter cord (kickback)
will pull your hand and arm toward the engine
faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.
When starting engine, pull the starter cord slowly until resis-
tance is felt and then pull rapidly to avoid kickback.
6. Rewind Start: Firmly hold the starter cord handle
(D, Figure 5). Pull the starter cord handle slowly until
resistance is felt, then pull rapidly.
NOTE: If the engine does not start after three attempts,
see the Troubleshooting section.
If the extension cord is damaged, it must be
replaced by the manufacturer (or its service
·½»ÄÊ ÅÈ · ɿÿ·ÈÂÏ Ç˷¿ »º Æ»ÈÉÅÄ ÊÅ ·ÌÅ¿º ·
hazard.
7. Electric Start: First connect the extension cord (E,
Figure 6) to the power cord receptacle (F) and then
into a wall receptacle. If additional extension cord is
required, make sure it is three-wire.
8. Electric Start: Depress the starter push button (G).
After you start the engine, first disconnect the extension
cord from the wall receptacle and then from the power
cord receptacle.
Important: To extend the life of the starter, use short
starting cycles (five seconds maximum). Wait one
minute between starting cycles.
NOTE: If the engine does not start after three attempts,
see the Troubleshooting section.
WARNING
WARNING