Snapper 1632E Operator's Manual
  1. Manuals
  2. Brands
  3. Snapper Manuals
  4. Snow Blower
  5. 1632E
  6. Operator's manual
Snapper 1632E Operator's Manual

Snapper 1632E Operator's Manual

Large frame snowthrowers
Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATOR'S
MANUAL
Large Frame
Snowthrowers
1226 Models
Mfg. No.
Description
1695324
L1226E, Snowthrower
1695325
L1226EX, Snowthrower (CE)
1695326
L1226E, Snowthrower
1695327
L1226EX, Snowthrower (CE)
1428 Models
Mfg. No.
Description
1695328
L1428E, Snowthrower
1695329
L1428EX Snowthrower (CE)
1695330
L1428E, Snowthrower
1695331
L1428EX Snowthrower (CE)
1530 Models
Mfg. No.
Description
1695332
L1530E, Snowthrower
1695333
L1530EX, Snowthrower (CE)
1695334
L1530E, Snowthrower
1695335
L1530EX, Snowthrower (CE)
1632 Models
Mfg. No.
Description
1695336
1632E, Snowthrower
1695337
1632EX, Snowthrower (CE)
1695338
L1632E, Snowthrower
1734892
Revision 02
Rev. Date 11/2007
TP 100-4613-02-LW-SN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1632E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Snapper 1632E

Summary of Contents for Snapper 1632E

  • Page 1 Mfg. No. Description 1695332 L1530E, Snowthrower 1695333 L1530EX, Snowthrower (CE) 1695334 L1530E, Snowthrower 1695335 L1530EX, Snowthrower (CE) 1632 Models Mfg. No. Description 1695336 1632E, Snowthrower 1695337 1632EX, Snowthrower (CE) 1695338 L1632E, Snowthrower Rev. Date 11/2007 TP 100-4613-02-LW-SN 1734892 Revision 02...

  • Page 2: Table Of Contents

    CONTENTS: Safety Rules & Information General...2 Training ...4 Preparation ...4 Operation...4 Children ...5 Clearing a Clogged Discharge Chute ...5 Service, Maintenance and Storage ...5 Emissions ...5 Decals...6 Safety Icons ...8 Identification Numbers...9 Features, Controls, & Operation Control Locations...10 General Operation Checks Before Each Start-Up ...12 Starting Controls...13 Starting the Engine...14...

  • Page 3: Operating Safety

    Safety Rules & Information Read the Manual The operator’s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation. Safe operating techniques, an explanation of the product’s features and controls, and maintenance information is included to help you get the most out of your equipment investment.

  • Page 4: Moving Parts

    Moving Parts This equipment has many moving parts that can injure you or someone else. However, if you are standing in the operator’s position, and follow all the rules in this book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet. Do not allow anyone near the equipment while it is running! DO NOT clear the discharge chute by hand.

  • Page 5: Training

    Safety Rules & Information This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

  • Page 6: Children

    21. Keep in mind the operator is responsible for acci- dents occurring to other people or property. 22. Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment-related injuries. These operators should evaluate their ability to operate the unit safely enough to protect themselves and others from injury.

  • Page 7: Decals

    Decals DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment. Although reading this manual and safety instructions it contains will provide you with the necessary basic knowl- edge to operate this equipment safely and effectively, we have placed several safety labels on the unit to remind you of this important information while you are operating...
  • Page 8 Part No. 1733772 Shift Decal Part No. 1733059 - DANGER / WARNING Main Dash Decal, CE, w/o Easy Turn Part No. 1727207 Discharge Chute Danger Decal ALL MODEL DECALS Part No. 1733443 Chute Release CE MODEL DECALS Part No. 1733060 - DANGER / WARNING Main Dash Decal, CE, w/ Easy Turn Part No.

  • Page 9: Safety Icons

    Safety Icons SAFETY ICONS WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwing objects and debris. Keep bystanders away. WARNING: REMOVE KEY BEFORE SERVICING. Remove the key, disconnect spark plug wire, and consult technical litera- ture before performing repairs or maintenance.

  • Page 10: Identification Numbers

    Part No. xxxxxxx xxxxxxxxxxxxxxx Serial No. xxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxx kg: xxx xxxxxxxxxxxxxxxxxxxxxxx kW: x.xx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxx 20xx xxxx max Identification Numbers When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.

  • Page 11: Features, Controls, & Operation

    CONTROL LOCATIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.

  • Page 12: Auger Control

    Speed Selector Selects forward speeds 1-6 and reverse speeds 1-2. No neutral position or gate is required, since the traction drive design automatically provides "neutral" (no forward or reverse movement), whenever the Drive Control is released. Traction Control / Free Hand™ Lock Engages traction drive to wheels when depressed.

  • Page 13: General Operation

    Operation GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with- out the clean-out tool properly stored on the auger housing.

  • Page 14: Starting Controls

    STARTING CONTROLS See Figure 1 for the following instructions. Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle. The Electric Start Button operates on 120 Volts AC, which is provided by connection to the extension cord provided with units equipped with this feature.

  • Page 15: Starting The Engine

    Operation STARTING THE ENGINE WARNING Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback.

  • Page 16: Stopping The Engine

    Figure 3. Engine Start/Stop A. Throttle Control Lever B. Fuel Shut-Off Valve C. Safety Key D. Choke Control Knob E. Primer Button F. Starter Cord Handle 9. Electric Start: First connect the extension cord to the power cord receptacle (A, Figure 4) and then into a wall receptacle.

  • Page 17: Operating The Snowthrower

    Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger engage control (C, Figure 5) on the right-hand grip to begin auger rota- tion.

  • Page 18: Ground Speed Selector

    GROUND SPEED SELECTOR Use the speed selector (A, Figure 5) to control the drive speed of the snowthrower. There are six forward speeds and two reverse speeds. Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.

  • Page 19: Easy-Turn And Traction Drive Lock

    Operation FULL TRACTION Both Wheels Drive Figure 8. Easy Turn Control EASY TURN™ FREEWHEELING AND TRACTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 8). Engaging the Easy Turn™ lever releases the left traction wheel but allows the right wheel to continue driving (Figure 8).

  • Page 20: After Each Use

    AFTER EACH USE Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls. Heat from the engine will usually prevent the snow from freezing solid while the unit is running, but after the engine is shut down, some snow may continue melting from engine heat, and later freeze around some moving parts as the unit cools.

  • Page 22: Regular Maintenance

    MAINTENANCE SCHEDULE Maintenance Required Check / Lubricate Free-Hand Linkage. Lubricate snowthrower. Check tire pressure. Change engine oil.* Clean or replace spark plug. Check drive linkage/belt tension. Lubricate Axle Shafts. Check auger gear case lubrication.** Lubricate Auger Shaft.*** * Change original oil after two hours of operation. ** Check oil level each fall and spring.

  • Page 23: Lubrication

    Regular Maintenance LUBRICATION IMPORTANT NOTE It is very important that grease fittings on the auger shaft are lubricated regularly. If auger rusts to shaft, damage to worm gear may occur if shear pins do not break. To prevent wheels rusting to axles, it is also nec- essary to remove the wheels and grease the axles regularly.

  • Page 24: Check / Lubricate Free-Hand Linkage

    CHECK / LUBRICATE FREE-HAND LINKAGE Check the function of the Free-Hand controls. The con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released. Lubricate as shown in Figure 16. IMPORTANT NOTE If the controls do not function properly, lubricate them.

  • Page 25: Troubleshooting, Adjustments, & Service

    TROUBLESHOOTING This section provides troubleshooting and service instructions. Locate the problem and check the possible cause/remedy in the order listed. Also, refer to the Engine Owner’s Manual for additional information. For problems not covered here, contact your local deal- Problem Engine fails to start.
  • Page 26 Problem Auger rotates, but snow is not- thrown far enough. Poor traction. Auger does not stop when auger lever is released. Snowthrower does not stop when drive lever is released. Discharge control is difficult to operate. Snowthrower veers to one side.

  • Page 27: Traction Drive Cable Adjustment

    Adjustments AUGER DRIVE ADJUSTMENT WARNING Do not over-tighten, as this may lift the lever and cause auger drive to be engaged without depress- ing the Auger Control. 1. Check that the auger cable (A, Figure 18) is on top of cable button (B) as show in Figure 18.

  • Page 28: Traction Drive Adjustment

    Figure 20. Traction Drive Cable Adjustment A. Cable Boot B. Traction Drive Cable C. “Z” Hook D. Cable Adjustment Bracket 4. Slide the cable boot (A) over the cable adjustment bracket. Run-In Adjustment ALL MODELS 1. After 5 hours of use, check for proper adjustment. Readjust clutch cable if necessary by increasing ten- sion on cable.

  • Page 29: Easy Turn Cable Adjustment

    Adjustments EASY TURN™ CABLE ADJUSTMENT If the Easy Turn™ cable has stretched, the gears will not disengage when the control lever is activated. Adjust the cable using the following procedure. 1. Turn the engine off and disconnect the spark plug wire.

  • Page 30: Shear Pin Replacement

    SHEAR PIN REPLACEMENT WARNING Do not go near the discharge chute or auger when the engine is running. Do not run the engine with any cover or guard removed. Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break.

  • Page 31: Belt Replacement

    Service BELT REPLACEMENT Auger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person. If the auger drive belt is damaged, the snow thrower will not discharge snow.
  • Page 32 Figure 30. Spout Rotator Rod A. Special Nut B. Cover C. Hair Pin D. Spout Rotator Rod 15. Index or point the spout rotator to the center of the machine so the rotator control is in the center of the dash panel.

  • Page 33: Traction Drive Belt

    Service Traction Drive Belt If the snow thrower will not move forward, check the trac- tion drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows. 1. Disconnect the spark plug wire. 2.

  • Page 34: Specifications

    NOTE: Specifications are correct at time of printing and are subject to change without notice. * The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05).

  • Page 35: Replacement Parts

    REPLACEMENT PARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. MAINTENANCE ITEMS Many convenient and helpful service and maintenance items are available from you authorized dealer. Some of these items include: Engine Oil...
  • Page 36 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com P R O D U C T S 535 Macon Street McDonough, GA 30253 www.Snapper.com © Copyright 2007, BRIGGS & STRATTON. All Rights Reserved. Printed in USA.

This manual is also suitable for:

1632exL11226exL1226exL1428eL1428exL1530e ... Show all

Table of Contents