Declaration Of Conformity - Bosch AKE 30-19 S Original Instructions Manual

OBJ_BUCH-1238-001.book Page 29 Friday, April 30, 2010 9:39 AM
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that
the product described under "Technical data" is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 2006/42/EC, 2000/14/EC.
EC Type Certification No. 3400653.01 CE by no-
tified testing agency No. 2140.
2000/14/EC: Guaranteed sound power level
105 dB(A).
Conformity assessment procedure according to
Annex V.
Equipment category: 6
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
19.01.2010
Assembly
For Your Safety
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
Caution! Do not touch the rotating chain.
Do not operate the chain saw near other
people, children or animals. Do not operate
the chain saw after drinking alcohol or un-
der the influence of intoxicating drugs or
medication.
Bosch Power Tools
Electrical Safety
Your machine is double insulated for safety and
requires no earth connection. The operating
voltage is 230 V AC, 50 Hz (for non-EU countries
220 V, 240 V as applicable). Only use approved
extension cables. Contact your Bosch Service
Centre for details.
Only extension cables of design type H07 RN-F
or IEC (60245 IEC 66) are permitted for use.
If you want to use an extension cable when op-
erating your product, only the following cable di-
mensions should be used:
2
– 1.0 mm : max. length 40 m
2
– 1.5 mm : max. length 60 m
2
– 2.5 mm : max. length 100 m
It is recommended for increased electrical safe-
ty to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
For products not sold in GB:
WARNING: For your safety, it is required that
the plug attached to the machine is connected
with the extension cord. The coupling of the ex-
tension cord must be protected against splash
water, be made of rubber or coated with rubber.
The extension cord must be used with a cable
strain relief.
The connection lead must be inspected for signs
of damage at regular intervals and may only be
used if in perfect conditions.
If the supply cord is damaged, it must be re-
placed by a Bosch Service Centre.
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fit-
ted in its place by an authorised customer serv-
ice agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be in-
serted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a resid-
ual current device (RCD) with a rated residual
current of 30 mA or less.
F 016 L70 667 | (30.4.10)
English | 29