Download Print this page

Advertisement

F 016 L70 558.book Seite 1 Donnerstag, 15. Januar 2009 3:18 15
Operating instructions
English
AKE 30-19 S
AKE 35-19 S
AKE 40-19 S

Advertisement

   Summary of Contents for Bosch AKE 30-19 S

  • Page 1

    F 016 L70 558.book Seite 1 Donnerstag, 15. Januar 2009 3:18 15 Operating instructions AKE 30-19 S AKE 35-19 S AKE 40-19 S English...

  • Page 2

    F 016 L70 558.book Seite 2 Donnerstag, 15. Januar 2009 3:18 15 Robert Bosch GmbH D-70745 Leinfelden Echterdingen 0 600 xxx xxx xxxV ~ xxHz xxx mm x A xxxx W xxxxxxxx 20xx ade in Germany 2 • F 016 L70 558 • 09.01...

  • Page 3

    F 016 L70 558.book Seite 3 Donnerstag, 15. Januar 2009 3:18 15 3-4 mm 3 • F 016 L70 558 • 09.01...

  • Page 4

    F 016 L70 558.book Seite 4 Donnerstag, 15. Januar 2009 3:18 15 50 mm 50 mm 4 • F 016 L70 558 • 09.01...

  • Page 5

    F 016 L70 558.book Seite 4 Donnerstag, 15. Januar 2009 3:18 15 5 • F 016 L70 558 • 09.01...

  • Page 6

    F 016 L70 558.book Seite 1 Donnerstag, 15. Januar 2009 3:18 15 Safety Notes WARNING! Read all safety warnings and all in- adapter plugs with earthed (grounded) power structions. Failure to follow the warnings and in- tools. Unmodified plugs and matching outlets will structions may result in electric shock, fire and/or se- reduce risk of electric shock.

  • Page 7

    F 016 L70 558.book Seite 2 Donnerstag, 15. Januar 2009 3:18 15 sure these are connected and properly used. Wear safety glasses and hearing protection. Use of these devices can reduce dust related Further protective equipment for head, hand, hazards. legs and feet is recommend.

  • Page 8

    Decreasing the depth gauge height can lead to in- creased kickback. Technical data Chain saw AKE 30-19 S AKE 35-19 S AKE 40-19 S Part number (typ) 3 600 H36 D.. 3 600 H36 E..

  • Page 9

    17 Fastening bolt If the supply cord is damaged, it must be replaced by 18 Guide fins for chain bar a Bosch Service Centre. 19 Oil outlet Products sold in GB only: Your chain saw is fitted 20 Symbol for rotation and cutting direction...

  • Page 10

    F 016 L70 558 - GB Seite 5 Donnerstag, 15. Januar 2009 3:31 15 Use only genuine Bosch chains designed for chainbars with 1.1 mm groove (guage). 4. Slide the chain 10 in the slot around the chain bar 11. Ensure chain is in correct running direc- tion by comparing with chain symbol 20.

  • Page 11

    Cutting unscrew cap. – Do not remove filter insert during filling. Before Cutting – Add Bosch biodegradable chain saw oil until res- Before and periodically during cutting check as fol- ervoir is full. lows: – Avoid dirt or debris entering oil tank, refit oil filler –...

  • Page 12

    Use of the saw to thin out branches or bushes is not – Always the hold chain saw firmly with both hands. approved. – Always use a Bosch low-kickback chain. Length cuts must be carried out with care, as lever- – Apply the metal gripping teeth 12 for leverage.

  • Page 13

    F 016 L70 558.book Seite 8 Donnerstag, 15. Januar 2009 3:18 15 Felling Trees To complete the felling operation, drive a wedge (Z) into the horizontal cut. Always wear hard hat to protect head against falling branches. Beware of falling branches when the tree starts to move.

  • Page 14

    Chain and Chain bar service agent. AKE 30-19 S ....F 016 800 259 Before returning, ensure all oil in the oil tank has been emptied by removing the sieve during emp- AKE 35-19 S .

  • Page 15

    F 016 L70 558.book Seite 10 Donnerstag, 15. Januar 2009 3:18 15 Fault Finding The following table gives checks and actions that you can perform if your machine does not operate correctly. If these do not identify/remedy the problem, contact your service agent. Warning: Switch off and remove plug from mains before investigating fault.

  • Page 16

    China Mainland or standardization documents: EN 60 745, accord- Bosch Power Tools (China) Co., Ltd. ing to the provisions of the directives 98/37/EC, 2000/14/EC, 2004/108/EC. 567, Bin Kang Road EC Type Certification No.

  • Page 17

    F 016 L70 558.book Seite 1 Donnerstag, 15. Januar 2009 3:18 15 (FI) (FI) 17 • F 016 L70 558 • TMS • 08.01.09...

  • Page 18

    F 016 L70 558.book Seite 2 Donnerstag, 15. Januar 2009 3:18 15 – – – – 18 • F 016 L70 558 • TMS • 08.01.09...

  • Page 19

    F 016 L70 558 - TJ Seite 3 Donnerstag, 15. Januar 2009 3:34 15 AKE 30-19 S AKE 35-19 S AKE 40-19 S 3 600 H36 D.. 3 600 H36 E.. 3 600 H36 F.. (SDS) 1900 1900 1900 –...

  • Page 20

    F 016 L70 558.book Seite 4 Donnerstag, 15. Januar 2009 3:18 15 230 V AC 50 Hz 220 V 240 V H07 RN - F IEC (60245 IEC 66) – 1,0 – 1,5 – 2,5 30 mA (RCD) 20 • F 016 L70 558 • TMS • 08.01.09...

  • Page 21

    F 016 L70 558.book Seite 5 Donnerstag, 15. Januar 2009 3:18 15 3-4 mm 1 – 7 – – 21 • F 016 L70 558 • TMS • 08.01.09...

  • Page 22

    F 016 L70 558.book Seite 6 Donnerstag, 15. Januar 2009 3:18 15 – – – – – – – – – – – – – – – – – 22 • F 016 L70 558 • TMS • 08.01.09...

  • Page 23

    F 016 L70 558.book Seite 7 Donnerstag, 15. Januar 2009 3:18 15 ( Y ) ( Z ) ( Y ) ( Z ) (X–W) 23 • F 016 L70 558 • TMS • 08.01.09...

  • Page 24

    F 016 L70 558.book Seite 8 Donnerstag, 15. Januar 2009 3:18 15 ( Z ) 1453 Dremel-Multi 24 • F 016 L70 558 • TMS • 08.01.09...

  • Page 25

    F 016 L70 558.book Seite 9 Donnerstag, 15. Januar 2009 3:18 15 AKE 30-19 S....F 016 800 259 AKE 35-19 S....F 016 800 260 AKE 40-19 S.

  • Page 26

    F 016 L70 558.book Seite 10 Donnerstag, 15. Januar 2009 3:18 15 www.bosch-pt.com 2002/96/EG 26 • F 016 L70 558 • TMS • 08.01.09...

  • Page 27

    (Stowmarket) www.bosch-pt.com.cn PT-LG/EAE (Leinfelden), 01.10.2007 Dr. Egbert Schneider Dr. Eckerhard Strötgen Senior Vice President Head of Product Engineering Certification 100156 70745 Leinfelden-Echterdingen Robert Bosch GmbH, Power Tools Division Deutschland 27 • F 016 L70 558 • TMS • 08.01.09...

  • Page 28

    F 016 L70 558 - Rückseite Seite 1 Donnerstag, 15. Januar 2009 3:40 15 Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com F 016 L70 558 (2009.01) O / 28 XXX...

This manual also for:

Ake 35-19 s, Ake 40-19 s

Comments to this Manuals

Symbols: 0
Latest comments: