Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pitney Bowes OptiFlow DIVS
Summary of Contents for Pitney Bowes OptiFlow DIVS
- Page 1 OptiFlow™ Vertical Power Stacker DIVS Operator Guide US/Canada English Version...
- Page 2 Your machine may not have some of the features described in this book. FastPac, E-Z Seal and OptiFlow are trademarks or registered trade- marks of Pitney Bowes Inc. ENERGY STAR is a registered trade- mark of the United States Environmental Protection Agency.
-
Page 3: Table Of Contents
Contents Important Safety Notes ..............1 OptiFlow™ Vertical Power Stacker Technology ......2 Capacity ................2 Stacker-to-Inserter Communications ........2 Stacker Access ..............2 Equipment Features ..............3 Adjusting Stacker Wall ..............4 Unloading Material...............4 Clearing Stalls from the Stacker ..........5 Clearing Stalls in a Stacker Attached to a DI380/DI425 or a DI500/DI600 ................6 Clearing Stalls in a Stacker Attached to a DI900/DI950 ....7 Getting the Most from Your Stacker..........8... - Page 4 Contents SV61322 Rev. C...
-
Page 5: Important Safety Notes
Follow these basic safety precautions when operating this machine and the specific occupational safety and health standards for your workplace: • Use only Pitney Bowes approved supplies, in particular aerosol dusters. Improper storage and use of aerosol dusters or flamma- ble aerosol dusters, can cause an explosive-like condition that could result in a personal injury and/or property damage. -
Page 6: Optiflow™ Vertical Power Stacker Technology
Optiflow™ Vertical Power Stacker Technology The Optiflow™ Vertical Power Stacker is a compact, powered, bot- tom-feed stacker that connects to the output of several Pitney Bowes Document Inserting Systems, including the DI380/DI425, the DI500/ DI600 and the DI900/950 Series. It neatly stacks the mail pieces fed from the inserter and keeps them in the same order as they were originally loaded. -
Page 7: Equipment Features
Operator Guide Equipment Features Front Vew Stacker Full Sensor Adjustable Stacker Wall Stacker Weight Sde Vew Stacker LED Handle (to pull Rear Vew out stacker) Power Reset Serial Switch Port Port Port (DI900/ (DI380/425/ 950) 500/600) SV61322 Rev. C... -
Page 8: Adjusting Stacker Wall
OptiFlow™ Vertical Power Stacker Adjusting Stacker Wall • Grasp the stacker wall from top and slide up or down to an ap- propriate position. Use the knob on rear to tighten wall into place. Full Height Position Stacker Wall Knob NOTE: It is possible that envelopes at the bottom of the stack could deform as stack weight increases. -
Page 9: Clearing Stalls From The Stacker
Operator Guide Clearing Stalls From the Stacker • Lift or remove material from stack and remove stalled piece. Stalled Piece • For DI380/425 and DI500/600 Series Inserters, slide out the stacker from the inserter base and remove the stalled piece or pieces as shown in the figure, right. -
Page 10: Clearing Stalls In A Stacker Attached To A Di380/Di425 Or
OptiFlow™ Vertical Power Stacker Clearing Stalls in a Stacker Attached to a DI380/DI425 or DI500/DI600 1. Slide the stacker out, away from inserter. 2. Lift the plastic cover (A) and lower the envelope exit area door (B) of the inserter. Remove stalled material and close latches. 3. -
Page 11: Clearing Stalls In A Stacker Attached To A Di900/Di950
Operator Guide Clearing Stalls in a Stacker Attached to a DI900/950 1. Push the stacker release lever UP. 2. Open the stacker as shown be- low and at the right. It's hinged on one side. Clear all stalled material from the stacker. 3. -
Page 12: Getting The Most From Your Stacker
• Excessive wetting may cause flap distortion. To alleviate this ® problem, use Pitney Bowes E-Z Seal solution in the inserter's sealing reservoir. You may also set the stacker wall to a lower position and/or remove part of the stack while the job is running. -
Page 13: Troubleshooting
Operator Guide Stacker Troubleshooting What the Stacker LEDs Mean DI380/425/500/600 DI900/950 No Light No power to stacker. No power to stacker. Green On Normal operation. No error. Normal Operation. Green Blinking Stacker almost full; Not applicable. remove stack. Amber Not applicable. Stacker almost full. - Page 14 OptiFlow™ Vertical Power Stacker Stacker Error Messages Displayed by DI500/DI600 Inserter (Continued) Error Message Solution Additional Comments E197 — Power Remove material None. Stacker Obstruction from Power Stacker, check for obstruc- tions, Press Clear Deck to continue. E198 — Power The power stacker is This is caused by not mov- Stacker Not...
-
Page 15: Stacker Error Messages-Di380/Di425 Inserter
Operator Guide Stacker Error Messages Displayed by DI380/DI425 Inserter Error Message Solution Additional Comments Stacker Not Check the serial You can also press STOP Detected; Press cable that connects to uninstall the stacker. This START to Retry or the power stacker disables stacker communica- STOP to Uninstall. - Page 16 OptiFlow™ Vertical Power Stacker Stacker Error Messages Displayed by DI380/DI425 Inserter (Continued) Error Message Solution Additional Comments E114 — Stacker Empty the stacker. This message occurs only if Full Press STOP Press START to you choose to continue run- resume operation ning the machine without or STOP to return emptying the stacker after...
-
Page 17: Stacker Error Messages-Di900/950 Inserter
Operator Guide Stacker Error Messages Displayed by DI900/DI950 Inserter Error Message Solution Displayed Additional Comments 230 — VPS Entry Stacker stopped. Check for and clear obstruc- Nip Jam Remove material tions in the stacker, espe- from stacker. cially in the entry area. It may be necessary to open the stacker (see page 7) to completely clear the stall. -
Page 18: Stacker Operation In Non-Communicating Mode
The error message will not occur again. The stacker is now in non-communicating mode; you can run it this way as a temporary measure until Pitney Bowes service can resolve the problem. IMPORTANT: Please note the following when you run the stacker in non-communicating mode: •... -
Page 19: Specifications
If this is a problem, set the height of the stacker wall at half-height rather than its fully extended posi- tion. Compatible Inserters The OptiFlow Vertical Power Stacker is designed to operate with the following Pitney Bowes Document Inserting Systems: • DI380 • DI425 •... -
Page 20: Envelope Size And Weight
XXXXXXX This document/data record is the property of Pitney Bowes Inc. and contains PROPRIETARY and CONFIDENTIAL information, and is not to be reproduced or distributed to any third parties without the express written authorization of Pitney Bowes, Inc. Any authorized reproduction of this Serial for DI380/DI425 and DI500/DI600 inserters;... -
Page 21: If You Need Assistance
Operator Guide If You Need Assistance USA Contacts ▪ Product Name: DIVS OptiFlow™Vertical Power Stacker ▪ For frequently asked questions, go to: and click on www.pb.com Customer Support ▪ To place requests for service or training, go to: and click on www.pb.com My Account ▪ To order PB supplies and accessories, go to: and click on www.pb.com Online Store ▪ To view and pay invoices online, go to: and click on www.pb.com My Account ▪... - Page 22 OptiFlow™ Vertical Power Stacker SV61322 Rev. C...
- Page 24 1 Elmcroft Rd. 5500 Explorer Drive Stamford, Connecticut 06926-0700 Mississauga, Ontario L4W5C7 www.pitneybowes.com www.pitneybowes.ca PB Form SV61322 Rev C (5/06) Printed in the USA or Canada Printed on recyclable paper *SV61322REVC*...