Download Print this page

Worksman PORTOTRIKE PT, PORTOTRIKE PT2F, PORTOTRIKE PTCB, PORTOTRIKE PT2CB, PORTOTRIKE PT3CB Owner's Manual

The compact deluxe adult folding tricycle

Advertisement

Quick Links

Worksman PortoTrike: The Compact Deluxe Adult Folding Tricycle
Assembly Instructions, Parts List, and Owner s Manual for PT, PT2F, PTCB, PT2CB, PT3CB
Congratulations on your purchase of the Worksman PortoTrike Compact
Folding Tricycle, one of the most popular adult recreational tricycles of all
time. This is a recreational tricycle for the consumer market, with a
recommended weight limit of 210-225 pounds, depending on brakes
chosen. The low step-through and compact frame design are ideal for
those riders who simply want to ride leisurely, safely, and comfortably.
The PortoTrike has been carefully manufactured in the USA using
domestic and imported parts, with simple finishing assembly required. It is
always recommended to have a qualified bicycle mechanic perform
repairs and assembly of any cycle. Please read these instructions
thoroughly prior to assembling and riding.
Failure to have this cycle professionally assembled could result in injury or death.
Tools Needed for Assembly:
(A) Unfolding the PortoTrike:
· Remove protective bubble wrap and
cardboard.
· Located at the PortoTrike s hinge, find the
quick-release arm, loosen it, and swing
towards the rear.
· Now that hinge is free, unfold the trike so that
the frame is straight.
· Slide quick-release arm s pin down through
frame hole, pull lever forward, and tighten.
(B) Steps to Attach Front Wheel/Front Fork to Main Frame:
a. Slide one bearing (49B) onto the fork
steerer tube cone, balls facing up.
b. Slide fork assembly into the front of the
frame; make sure that bearing is flat.
c. Place the remaining bearing (49B), balls
facing downward, onto the steerer tube.
d. Thread top adjustment cone (52B) onto
this tube. Tighten the bottom. Again,
make sure both bearings are sitting
evenly inside their respective cones.
Hand-tighten until tube is tight enough
the sit steady but can still turn freely.
e. Place keyed silver washer (53) above the
adjustment cone. (Key inside slot in tube.)
f. Next, place quick release clamp (4911B
it has a black handle) above washer, with
clamp arm towards the back of the cycle.
g. Next, place reflector bracket (5030F) on top
of the clamp with key inside slot as done
before. Make sure holes point upwards.
h. Place 2 regular washers (53B) above the reflector bracket, followed by the small black-keyed washer (53BWO),
and then screw on the threaded lock nut securely (54B).
Note: Headset assembly should be tight enough so all pieces are touching and there are no loose pieces.
Phillips and Flathead Screwdrivers, Large Adjustable Wrench
(a)
(d)
(f)
(b)
(e)
(g)
- 1 -
(c)
(h)

Advertisement

loading
Need help?

Need help?

Do you have a question about the PORTOTRIKE PT, PORTOTRIKE PT2F, PORTOTRIKE PTCB, PORTOTRIKE PT2CB, PORTOTRIKE PT3CB and is the answer not in the manual?

Questions and answers

Summary of Contents for Worksman PORTOTRIKE PT, PORTOTRIKE PT2F, PORTOTRIKE PTCB, PORTOTRIKE PT2CB, PORTOTRIKE PT3CB

  • Page 1 Worksman PortoTrike: The Compact Deluxe Adult Folding Tricycle Assembly Instructions, Parts List, and Owner s Manual for PT, PT2F, PTCB, PT2CB, PT3CB Congratulations on your purchase of the Worksman PortoTrike Compact Folding Tricycle, one of the most popular adult recreational tricycles of all time.
  • Page 2 - 2 - (C) Handlebar Set Up: · Open quick-release clamp (4911B) on headset assembly. · Insert handlebar stem (55E) into the front tube, with the head of the stem facing forward. NOTE: Must be at least 4 into the tube, or damage to fork may occur. ·...
  • Page 3 Only use factory original replacement parts. Lubricate chain, caliper brake pivot bolt and other parts as necessary and at least once every 6 months. How to Fold Your Worksman Folding Port-o-Trike Tricycle To fold, pull the Safety-Loc lever to the loose position. Pivot the lever toward the side of the tricycle.
  • Page 4 - 4 - Replacement Parts List: (PT, PT2F, PTCB, PT3CB) Please note that there are two styles of PT rear axles and drive wheels. Style A uses a round drive plate welded to the axle with three prongs that protrude into three holes in the hub of the drive wheel. Style B uses a keyway, which is a rectangular piece of steel that slips between a groove in the axle and a slot in the drive wheel hub.
  • Page 5: Braking System

    Reflector Kits for Tricycles ** On 3 speed models, please note the brand and shifter style. Your Worksman PT3CB will be equipped with a quality 3 speed and shifter, but brand and shifter style may vary. Parts listed here are the most commonly used Sturmey Archer style. For Shimano Parts, call 718-322-2000.
  • Page 6 When you need a unique specialty cycle, call WORKSMAN CYCLES! INDUSTRIAL HEAVY-DUTY TRICYCLES Worksman Adaptable Tricycles Worksman Front-Load Tricycles Worksman Executive Trike Worksman Chariots Worksman Mover Tricycles WORKSMAN HEAVY-DUTY INDUSTRIAL & DELIVERY BICYCLES, CRUISERS, FOLDING BICYCLES WORKSMAN RECREATIONAL TRICYCLES FOR ADULTS AND CHILDREN 888-3-WHEELER www.worksman.com...