Table of Contents
Advertisement
Keep this user guide with your appliance. If the appliance is ever sold or transferred to another person,
ensure that the new owner receives the user guide. Please become familiar with these recommendations
before installing and using your oven. They were written for your safety and the safety of others
0
Identification
0.1
Installation
- The appliance must be unplugged during installation
or when any repairs or maintenance work is being per-
formed.
- Ensure that the network voltage corresponds to the
voltage noted on the identification plate located inside
the hood.
- If the electrical installation at your residence requires
any changes in order to hook up your Appliance, call
upon a professional electrician.
- If the hood is being used in evacuation mode, do not
connect the appliance to a combustion gas exhaust
duct (boiler, chimney, etc.) or to a CMV (controlled me-
chanical ventilation) system.
- Under no circumstances should the exhaust duct
empty into the attic.
- Install the hood at a safe distance of at least 70 cm
from an electric, gas or combined cooking hob.
ELECTRICAL CONNECTIONS
During installation and maintenance operations, the ap-
pliance must be unplugged from the electrical grid;
fuses must be cut off or removed.
The electrical connections are made before the appli-
ance is installed in its housing.
Ensure that:
- the electrical installation has sufficient voltage,
- the electrical wires are in good condition,
- the diameter of the wires complies with the installation
requirements.
USING THE EVACUATION MODE
1.1
If you possess an outlet to the exterior
Your hood can be connected to this outlet using a
flue (minimum diameter Ø mm that is enamelled, in
aluminium, flexible or made of inflammable material).
If your flue is less than 125 mm in diameter, you must
use the recycling mode.
1.2
USING THE RECYCLING MODE
If you do not possess an outlet to the exterior
All of our appliances can be used in recycling mode.
In this case, you should add an active carbon filter
which will keep in odours.
Warning
This appliance is delivered with a H 05 VVF power cord
that has three-0.75 mm
ground). It must be connected to the main power sup-
ply (which should be a 220-240 V single phase current)
via a CEI 60083 standardised socket that should remain
accessible after installation, in keeping with installation
guidelines.
We cannot be held responsible for any accident result-
ing from an inexistent, defective or incorrect ground
lead. The fuse for your installation must be 10 or 16A.
If the power cable is damaged, call the after-sales serv-
ice department in order to avoid danger.
If the electrical installation at your residence requires
any changes in order to hook up your appliance, call
upon a professional electrician.
If the hood displays any malfunctions, unplug the ap-
pliance or remove the fuse corresponding to the elec-
trical socket where your appliance is plugged in.
The hood must be installed in compliance with all appli-
cable regulations concerning the ventilation of premises.
In France these regulations are described in DTU 61.1
from the CSTB. In particular, the evacuated air should
never be conveyed to a duct used to evacuate smoke
from appliances that use gas or other combustible fuels.
Unused ducts may only be used after approval from a
competent specialist.
The accessible parts of this appliance may become
hot if it is used with a cooking appliance.
1.3
ASSEMBLING THE HOOD
The minimum distance between the cooking surface
and the lowest part of the hood must be 70 cm. If the
instructions for the hob installed under the hood spec-
ify a distance of more than 70 cm, this requirement
must be respected.
— Draw a horizontal line 70 cm minimum from the cook
top (A).
— Draw a vertical line (B) on the wall that is centred over
the cook top and that extends from the horizontal
line drawn in the previous step (A) to the ceiling.
— Cut the drilling template by following the dotted lines
to obtain two parts, C1 and C2.
— Place the C2 template (fig. 1) on the wall, superimpos-
ing the line that represents the hood's axis over ver-
tical line B drawn in a previous step.
— Place the C1 template against the wall flush with the
ceiling.
— Drill the six holes. Insert the 6 wall plugs.
- Screw the two screws from the top of the hood
(D1.3.1) by leaving 5 mm.
- Hang the hood with two screws (D1.3.1).
- Remove the filter cassettes (F1.3.2).
- Screw the two screws on the bottom (E1.3.2).
Before clamping screws complete 4 D and E, adjust
21
the level of the hood.
2
conductors (neutral, phase and
EN
Advertisement
Table of Contents
