Turning the Power ON .......................2-6 Turning the Power OFF......................2-7 Loading Roll Media onto the Unwinder.................2-7 Operating the Winder ......................... 2-17 Removing a Printed Media Core from the Winder ............2-19 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Do not use organic solvents or gasoline to clean the labels. Warning labels must be replaced if damaged, lost, or cannot be read. Contact your local Xerox Representative if an warning label needs to be replaced. 8264E Color Wide Format Printer 100kg Unwinder / Winder...
Safety and Warning Label Information Warning Label Locations and Types The figures below indicate the locations of the warning labels. Figure 1 Front Warning Label Locations 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 7
Safety and Warning Label Information Figure 2. Rear Warning Label Locations 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Do not use organic solvents or gasoline to clean the labels. Operating instructions labels must be replaced if damaged, lost, or cannot be read. Contact your local Xerox Representative if an warning label needs to be replaced. 8264E Color Wide Format Printer 100kg Unwinder / Winder...
Safety and Warning Label Information Instruction Label Locations and Types The figures below indicate the locations of the operating instruction labels. Figure 3. Operating Instruction Label Location Types of operating instruction labels 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Tension Roller activates the Unwinder Motor to feed paper into the printer. Unwinder / Winder Power Switch Used to turn the Unwinder / Winder power ON and OFF. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Media Core Used to roll in the media after printing. Unwinder / Winder Control Panel Used to set the operating condition and to display the status of the product. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Error Lamp Blinking Time-out error. No error. Winder Control Panel The Winder Control Panel is used to set the operating mode and to display the status of the Winder. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
State Function • Power is ON. Power Lamp • Stand-by. Blinking During roll-in operation. Power is OFF. Over-current error in roll-in motor. Error Lamp Blinking Time-out error. No error. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
This section describes the procedure for connecting the power cable. CAUTION DO NOT use a damaged power cable. If the power cable is damaged, contact your local Xerox Customer Service Representative for a replacement. Use the following instructions to install the power cable.
1. Set the Unwinder / Winder power switch to the ON position. The operation lamp will light. Figure 10. Set the Power Switch to the ON Position Part Name Unwinder / Winder Power Switch 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Roll media must be loaded in the center of the printer. 1. Set the Unwinder / Winder Power Switch to ON. 2. Set the Automatic Operation Switch to OFF. Figure 12. Set Unwinder Automatic Operation Switch to OFF 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 18
Figure 14. Install Roll Media Part Name Rear Rail Roll Media 5. Set the roll media on the Left Unwinder Spindle and tighten the Left Unwinder Spindle Locking Handle. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 19
7. Loosen the Left and Right Unwinder Spindle Locking Handles and move the roll media to the center of the rail so that the media is aligned with the center of the printer. Tighten the Left and Right Unwinder Spindle Locking Handles. 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 20
9. Raise the Media Set Lever. The Printer Control Panel will display “Please Set Media”. Figure 18. Install Roll Media Part Name Media Set Lever 10. Open the Printer Front Cover. 2-10 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 21
12. Raise the tension roller located on the rear of the product with your hands. Roll media will automatically be fed out. Figure 21 Raise the Tension Roller 8264E Color Wide Format Printer 100kg Unwinder / Winder 2-11 User Guide...
Page 22
Unwinder / Winder Operation Part Name Roll Media Tension Roller 2-12 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 23
Figure 22. Insert Paper into Tension Roller Part Name Roll Media Unwinder Tension Bar Roller Rear Printer Platen When using a roll paper where the print surface is on the inside. 8264E Color Wide Format Printer 100kg Unwinder / Winder 2-13 User Guide...
Page 24
Rear Printer Platen 14. Pull about 1 meter of roll media out from the Front Printer Plate. Figure 14. Install Roll Media Part Name Roll Media Front Printer Platen 2-14 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 25
Ensure the right edge of the roll media is not to the right of the Media Setting Guide. Setting the media to the right of the Media Setting Guide may affect the print quality. 8264E Color Wide Format Printer 100kg Unwinder / Winder 2-15...
Page 26
Figure 26. Install Roll Media Part Name Roll Media Media Setting Guide 16. Lower the Media Set Lever. Figure 27. Lower Media Set Lever Part Name Media Set Lever 2-16 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 27
17. Push the “INITIALIZE” button on the Unwinder Control Panel. Figure 28. Push INITIALIZE 18. Close the Printer Front Cover. Figure 29. Close the Printer Front Cover Part Name Printer Front Cover 8264E Color Wide Format Printer 100kg Unwinder / Winder 2-17 User Guide...
4. Attached the tip of the roll media to the media core on the Winder Spindles. Ensure that the media parallel to the core. Secure the tip of the media to the core with tape. Figure 31. Attach the Media to the Core Part Name 2-18 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...
Page 29
When using roll paper where the print surface is on the outside: OUTSIDE ROLL • When using roll paper where the print surface is on the inside: INSIDE ROLL Figure 32. Set Automatic Operation Switch 8264E Color Wide Format Printer 100kg Unwinder / Winder 2-19 User Guide...
Figure 33. Set Manual Operation Switch 4. Remove the printer media core from the Winder and install a new empty media core on the Winder Spindles. 2-20 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide...