Installation Instructions 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Catalog number 1738-AENTR, Series B Table of Contents Topic Page Important User Information Environment and Enclosure Preventing Electrostatic Discharge Additional Resources About The Adapter Before You Begin Determine Compatibility Understand Messaging...
2 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences between...
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Environment and Enclosure ATTENTION: This equipment is intended for use in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments.
1770-IN041. techniques. If you would like a manual, you can: • download a free electronic version from the internet: http://www.rockwellautomation.com/literature/ • purchase a printed manual by contacting your local Allen-Bradley distributor or Rockwell Automation representative. Publication 1738-IN030A-EN-P - July 2013...
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter About The Adapter The Series B 1738-AENTR ArmorPOINT I/O Dual Port EtherNet/IP Adapter provides connectivity to an EtherNet/IP network via two M12 EtherNet-keyed connectors for 2-port pass-through to support daisy chains or rings, and the existing star and tree network topologies.
6 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Before You Begin To effectively use your adapter, note the following considerations. Determine Compatibility RSLogix 5000 version 17 or greater must be used for the 1738-AENTR Add-on Profile. ™ The 1738-AENTR adapters will accept I/O connections with electronic keying for the 1738-AENT.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Mount the Adapter and I/O Base To mount the ArmorPOINT I/O adapter on a wall or panel, use the screw holes provided in the adapter. A mounting illustration for the ArmorPOINT adapter with several attached I/O bases is shown below.
Page 8
8 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter 4. Ground the system using the ground lug connection in the adapter’s I/O base. (The ground lug connection is also a mounting hole). 5. Add one or more I/O modules and their respective I/O mounting bases to the adapter and its I/O Mounting base as required.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Set the Network Address The adapter ships with the rotary network address switches set to 999 and DHCP enabled. To change the network address, you can: • adjust the switches on the front of the module •...
IP enclosure type requirements. Auxiliary power cable: standard cordset (single-ended), for example Allen-Bradley part number 889N-F4AFC-6F or 889N-R4AFC-6F; or standard patchcord (double-ended), for example, Allen-Bradley part number 889N-F4AFNU-6F or 889N-F4AFNV-6F. Refer to publication M117-CA001A-EN-P for more information.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Interpret Status Indicators Refer to the following diagram and table for information on how to interpret the status indicators. ArmorPOINT I/O Dual Port EtherNet/IP Adapter, Series B Link 1 Activity/Status indicator Link 2 Activity/Status...
Page 12
12 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Indicator Status for Modules Indicator State Description Network No link established with Port 1 or Port 2. Activity Flashing green Transmit or receive activity present on Port 1 and/or Port 2 @ 100 Mbps.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Specifications ArmorPOINT I/O EtherNet/IP Adapter — 1738-AENTR, Series B Attribute Value Expansion I/O capacity, max • 63 modules • 5 rack-optimized connections (for digital modules only) • 31 direct connections • 1738-AENTR backplane current output = 0.8 A.
14 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Power Supply Attribute Value Inrush current, max 6 A for 10 ms Input overvoltage protection Reverse polarity protected POINTBus output current, max 5V DC @ 0.8A Auxiliary power cable Standard cordset (single-ended), for example Allen-Bradley part number 889N-F4AFC-6F or 889N-R4AFC-6F.
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter General Specifications Attribute Value Input overvoltage protection Reverse polarity protected Thermal dissipation, max 21.5 BTU/hr @ 28.8V DC Isolation voltage 50V (continuous), Basic Insulation Type. Type Tested @ 500V AC for 60 s: •...
Page 17
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Certifications Certification (when Value product is marked) c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E322657. European Union 2004/108/EC EMC Directive, compliant with: EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2;...
Page 18
18 1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Notes: Publication 1738-IN030A-EN-P - July 2013...
Page 19
1738 ArmorPOINT I/O Dual Port EtherNet/IP Adapter Notes: Publication 1738-IN030A-EN-P - July 2013...
RA-DU002, available at http://www.rockwellautomation.com/literature/. Allen-Bradley, Rockwell Automation, POINT I/O, ArmorPOINT I/O, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Publication 1738-IN030A-EN-P - July 2013...