Operation; Correct Use Of Standard Accessories; Recommended Cleaning Procedure; Storage - Black & Decker PW1200 Manual

• The washer must be used standing on a
secure, stable, positioned as shown. FIG.2.
• Fit the lance into the gun and rotating it until
the two parts are completely locked FIG. 3
• Connect the gun to the high pressure hose
FIG.4
• Connect the high pressure hose to the water
outlet on the washer FIG.5.
• Connect the water supply hose to female
coupler FIG.6, then connect to the water inlet
of the washer. The supply hose must have an
internal diameter of at least 13mm (1/2 in.) and
must be reinforced. The water supply must be
at least equal to the washer delivery capacity.
NOTE: The Machine Not Suitable For Connection
To The Potable Water Main (Fig. 13).
WARNING: The intake water
temperature must not exceed
40oC. The water supply must not
exceed 0.7 MPa.
CAutIoN: The washer must only
be used with clean water; use
of unfiltered water of corrosive
chemicals will damage the washer.
• Push the motor switch to "OFF" position FIG.
8.
• Check that the electrical supply voltage and
frequency (Volt/Hz) correspond to those
specified on the washer rating plate. If the
power supply if correct, you may now plug in
the washer.

7. OpERATION

• Turn on the water supply tap fully.
• Release the safety lock FIG.7, then press the
trigger for a few seconds to allow air to escape
and to discharge residual pressure in the hose.
• Keeping the trigger pressed, push the switch
to start the motor FIG.8.
• When re-starting the motor, always keep the
trigger pressed.
WARNINg: Before Starting Up The
Appliance Check That The Water
Supply Hose Is Connected Properly;
Use Of The Appliance Without
Water Will Cause Damage To The
Appliance.
NOTE: The Motor Only Runs When The Trigger Is
Operated.

CORRECT USE Of STANDARD ACCESSORIES

• The washer is equipped with the adjustable
nozzle.
• Jet adjustment from pencil to fan FIG.9.
WARNINg: Do Not Adjust The
Nozzle While The Trigger Is
Squeezed.

RECOMMENDED CLEANINg pROCEDURE

• Dissolve dirt by applying the detergent mixed
with water to the surface while still dry. When
dealing with vertical surfaces work from the
bottom upwards.
• Leave the detergent to act for 1-2 minutes but
do not allow the surface to dry.
• Starting from the bottom, use the high pressure
jet at a minimum distance of 30 cm. Do not
allow the rinse water to run onto unwashed
surfaces.
• In some cases, scrubbing with brushes is
needed to remove dirt.
• High pressure is not always the best solution
for good washing results, since it may damage
some surfaces.
• The finest adjustable nozzle jet setting or
the rotating nozzle should not be used on
delicate or painted parts, or on pressurized
components (e.g. tires, inflation valves, etc.).
• Effective washing depends on both the
pressure and volume of the water used, to the
same degree.
STORAgE (fIg.10 – fIg. 12)
• Switch off the washer.
• Turn off the water supply tap.
• After use, the detergent residuals should be
removed from the tank.
• Discharge residual pressure by pressing the
trigger until no more water comes out of the
lance nozzle.
• Engage the gun safety lock.
• Remove the plug from the socket.
• Operate the washer with non-corrosive/ non-
toxic antifreeze before storing for the winter.
WARNINg: Before Reusing,
Completely Flush The Unit Out
With Plain Water. Anti-Freeze Can
Damage Paintwork So You Must
Ensure There Is No Anti-Freeze
Left In The System Before Using It
Again.
English 9