Table of Contents
Advertisement
Available languages
Available languages
Cross threading will cause leaks.
NoTE: Before connecting the garden hose to the
pressure cleaner, run water through the garden hose
for thirty seconds to clear any debris from the mouth of
the garden pressure hose.
To connect the quick connect hose adapter
transparent filter with quick connect
cleaner
, push the quick connect hose adapter firmly
2
onto the transparent filter.
NoTE: Before use, gently tug on the garden hose to
ensure the connection is secured. Make sure the quick
connect hose adapter is flush with the transparent filter
as shown in Figure F.
2. Always disconnect the garden hose after usage. To
disconnect, pull back the collar on the quick connect
hose adapter and remove from the transparent filter.
To Attach the Suction Hose (Fig. F, G)
Use the suction hose to pull water from a bucket or other
fresh water source.
NOTICE: Do not use to suction soap, chemicals, dirty or
corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use salt water.
1. To connect the quick connect hose adapter
end of the suction hose to the water intake with filter
on the pressure cleaner
adapter firmly onto the water intake with the transparent
filter.
NoTE: Before use, gently tug on the garden hose to
ensure the connection is secured. Make sure the quick
connect hose adapter on the end of the suction hose
is flush with the quick connect filter as shown in the
Figure F.
2. Place other end of suction hose with filter on it into
container of fresh water or a fresh water source. Adjust
the float on the suction hose so the filter stays covered
in the liquid.
3. After the job being performed is complete, place the
suction hose into container of clean water and draw the
clean water through the system to rinse.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the Battery Pack
(Fig. H)
NoTE: For best results, make sure your battery pack is
fully charged.
To Install the Battery Packs
1. Lift and hold the battery port cover
battery port
17
.
to the
8
on the pressure
3
on the
13
, push the quick connect hose
2
18
up to expose the
2. Align the battery pack with the rails inside the
tool's handle and slide it into the handle until the battery
pack is firmly seated in the tool and ensure that it does
not disengage.
3. Close the battery port cover
latched into position before starting tool.
To Remove the Battery Pack
1. Lift and hold the battery port cover
battery pack
6
2. Press the battery release button
and firmly pull the battery pack
3. Insert the battery into the charger as described in the
charger section of this manual.
Proper Hand Position (Fig. I)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of
a sudden reaction.
Proper hand position requires one hand on the main
handle
and the other hand on the pressure cleaner's
1
body as shown.
3
Speed Selector (Fig. J)
This pressure cleaner gives you the choice to operate at
a lower pressure for more delicate jobs, or accelerate the
pressure cleaner speed for high-performance cleaning.
To accelerate, pull the speed selector
the spray wand
1
applications that need higher PSI.
For low pressure, push the speed selector back toward the
main handle
9
into the "LO" position. This mode is best for
larger projects that require more time to complete.
NoTE: When in "HI" mode, runtime will be decreased as
compared to when pressure cleaner is in "LO" mode.
Pressure Washing
Preparing Surface for Cleaning
•
Remove objects from the area which could create
a hazard.
•
Ensure that all doors and windows are closed tight. Protect
all plants and trees in the adjacent area with a drop cloth
ensuring that they will not be harmed by any overspray.
•
Pre-rinse cleaning area with fresh water.
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area before use.
Preparing Power Cleaner Unit for Use
DANGER: Risk of fluid injection and laceration.
When using the high-pressure setting, DO NOT allow
the high-pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
. Ensure the cover is fully
18
18
up to expose the
.
on the battery pack
5
out of tool.
6
16
forward toward
into the "HI" position. This mode is best for
ENGlIsh
6
2
29
Advertisement
Table of Contents
