Table of Contents
Advertisement
Available languages
Available languages
Attaching Nozzles (Fig. A, E)
DANGER: Risk of fluid injection. Do not direct discharge
stream toward persons, unprotected skin, eyes or any pets
or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while pressure
washer is running. Turn pressure washer unit OFF before
changing nozzles.
1. To connect a nozzle to the spray wand
the nozzle button
3
on the spray wand and insert the
appropriate nozzle.
2. Release the button to lock the nozzle in place.
3. Give the nozzle a firm tug to ensure the nozzle is locked
into place.
Spray Fan to Pencil Jet Nozzle
Adjusting Fan Pattern (Fig. E1, E2)
The angle of spray coming out of the spray wand may be
adjusted by rotating the nozzle. This will vary the spray pattern
from approximately a 0 ° narrow high impact stream to a 60 °
wide fan spray.
A wide fan pattern distributes the impact of the water over a
larger area, resulting in excellent cleaning action with a reduced
risk of surface damage. Large surface areas can be cleaned more
quickly using a wide fan pattern.
A narrow pencil jet stream distributes the impact of the water
in a concentrated area, resulting in a high impact force on
the cleaning surface. Use a narrow pencil jet stream for deep
cleaning in a concentrated area. However, use it cautiously, as it
may damage some surfaces
Attaching Soap Bottle (Fig. J3)
To connect the soap bottle
end of the soap bottle inside the spray handle and turn the soap
bottle counterclockwise to lock it into position.
nOTE: The wand and soap bottle cannot be installed at the
same time.
nOTE: The soap bottle should be positioned underneath the
barrel of the spray handle. Do not position the soap bottle
above the barrel of the plastic gun as this will lead to soap
dripping on the barrel.
spray Tip
Spray fan to pencil jet nozzle
Turbo Nozzle
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
2
, depress
16
to the spray handle
4
, insert the
Application
For gentle wide area cleaning.
For abrasive cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
Pressure Washing
Preparing Surface for Cleaning
•
Remove objects from the area which could create a hazard
such as children's toys or outdoor furniture.
•
Insure that all doors and windows are closed tight.
•
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre‑rinse cleaning area with fresh water.
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area before use.
Preparing Pressure Washer Unit for Use
(Fig. K, K1, K2, K3)
DANGER: Risk of fluid injection and laceration. When
using the high‑pressure setting, DO NOT allow the
high‑pressure spray to come in contact with unprotected
skin, eyes, or with any pets or animals. Serious injury
will occur.
CAUTION: Before operation:
1. Connect the garden hose to a water supply. Water can be
drawn from a faucet or another water supply. Refer to self
Priming under Preparing Pressure Washer Unit for Use.
2. Connect the high pressure hose to the pressure washer and
the spray handle. For instructions on connecting the high
pressure hose to the pressure washer and spray handle,
please refer to Attaching high Pressure hose under
Assembly and Adjustments.
3. Connect the garden hose to the pressure washer. For
instructions on connecting the water supply to the pressure
washer, please refer to Attaching garden hose under
Assembly and Adjustments.
4. Plug the power cord into an appropriate power source.
Preparing Spray Handle (Fig. A)
iMPORTAnT: Before turning on the pressure washer unit,
disengage the trigger lock‑off
1. Disengage the trigger lock‑off
2. Squeeze the trigger
7
. Hold the trigger for 30 seconds to
purge the system of air.
English
4
.
6
and squeeze the trigger
7
6
.
.
9
Advertisement
Table of Contents
