Black & Decker KG2001 Manual page 10

ENGLISH
Make sure that the disc locates correctly on the

inner fl ange.
Place the outer fl ange (14) onto the spindle.

When fi tting a grinding disc, the raised centre on
the outer fl ange must face towards the disc (A
in fi g. E). When fi tting a cutting disc, the raised
centre on the outer fl ange must face away from
the disc (B in fi g. E).
Keep the spindle lock (4) depressed and tighten the

outer fl ange using the two-pin spanner (15) (fi g. F).
Removing
Keep the spindle lock (4) depressed and loosen

the outer fl ange (14) using the two-pin spanner
(15) (fi g. F).
Remove the outer fl ange (14) and the disc (12).

Use
Warning! Let the tool work at its own pace. Do not
overload.
Carefully guide the cable in order to avoid ac-

cidentally cutting it.
Be prepared for a stream of sparks when the

grinding or cutting disc touches the workpiece.
Always position the tool in such a way that the

guard provides optimum protection from the
grinding or cutting disc.
Switching on and off
To switch the tool on, press the lock-off button

(2) and subsequently press the on/off switch (1).
To switch the tool off, release the on/off switch (1).

Warning! Do not switch the tool off while under
load.
Hints for optimum use
Firmly hold the tool with one hand around the

side handle and the other hand around the main
handle.
When grinding, always maintain an angle of approx.

15° between the disc and the workpiece surface.
Maintenance
Your Black & Decker corded/cordless appliance/tool
has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
Switch off and unplug the appliance/tool.

Or switch off and remove the battery from the ap-

pliance/tool if the appliance/tool has a separate
battery pack.
10
Or run the battery down completely if it is integral

and then switch off.
Unplug the charger before cleaning it. Your

charger does not require any maintenance apart
from regular cleaning.
Regularly clean the ventilation slots in your ap-

pliance/tool/charger using a soft brush or dry
cloth.
Regularly clean the motor housing using a damp

cloth. Do not use any abrasive or solvent-based
cleaner.
Regularly open the chuck and tap it to remove

any dust from the interior (when fi tted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fi tted:
Safely dispose of the old plug.

Connect the brown lead to the live terminal in

the new plug.
Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth
terminal. Follow the fi tting instructions supplied with
good quality plugs.Recommended fuse: 13 A.
Protecting the environment
Separate collection. This product must
not be disposed of with normal household
waste.
Should you fi nd one day that your Black & Decker
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and
packaging allows materials to be recy-
cled and used again. Re-use of recycled
materials helps prevent environmental
pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collec-
tion of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
Black & Decker provides a facility for the collection
and recycling of Black & Decker products once they
have reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest au-
thorised repair agent by contacting your local