Programming Options (Numerical Order) - C&K systems SYS3316RF Installation Instructions Manual

SYS3316RF Installation Manual
Command Location 00: Installer Combination Command Location 00: Installer Combination Command Location 00: Installer Combination
Command Location 00: Installer Combination Command Location 00: Installer Combination
Digit Positions (1) - (6): Installer Combination
Combination must have 6 digits. Valid entries are 0 - 9.
Command Location 01 - 08 and 51 - 68: Command Location 01 - 08 and 51 - 68:
Command Location 01 - 08 and 51 - 68: Command Location 01 - 08 and 51 - 68: Command Location 01 - 08 and 51 - 68:
01 = User #1 (Master)
02 = User #2
03 = User #3
04 = User #4
05 = User #5
06 = User #6
07 = User #7
08 = User #8 (Guest)
51 = User #9
52 = User #10
53 = User #11
54 = User #12
55 = User #13
Digit Position (1): Arming Type
1 = Arm Only, No Closing (C) Report, No Shunting
2 = Disarm Only, No Opening (O) Report, No Shunting
3 = Arm and Disarm, No O/C Reports, No Shunting
4 = Arm Only, with Closing Report, No Shunting
5 = Disarm Only, with Opening Report, No Shunting
6 = Arm and Disarm, with O/C Reports, No Shunting
7 = Arm Only, No Closing Report, Shunting Allowed
8 = Disarm Only, No Opening Report, Shunting Allowed
9 = Arm and Disarm, No O/C Reports, Shunting Allowed
0 = Arm Only, with Closing Report, Shunting Allowed
1 = Disarm Only, with Opening Report, Shunting Allowed
2 = Arm and Disarm, with O/C Reports, Shunting Allowed
Digit Positions (2) - (6): Arming Combination (PIN)
Combination may have from 2 - 5 digits. Valid entries are 0 -9.
Default Values Default Values Default Values Default Values Default Values
**Default Values **Default Values **Default Values
**Default Values **Default Values
56 = User #14
63 = User #27
57 = User #15
64 = User #28
58 = User #16
65 = User #29
59 = User #17
66 = User #30
5A = User #18
67 = User #31
5B = User #19
68 = User #32
5C = User #20
5D = User #21
5E = User #22
5F = User #23
60 = User #24
61 = User #25
62 = User #26
NOTE: Opening and Closing Reports
0 1
0 0 0 0 0 0 0 0 0 0
(1) (2)
User Arming Type and Combination User Arming Type and Combination
User Arming Type and Combination User Arming Type and Combination User Arming Type and Combination
9
0 0 0 0 0 1 1 1 1 1
(1) (2)
must be enabled. See CL 2C
Digit Positions 1 and 3 for
additional information.
8
CL 00 - 08 & 51 - 68 CL 00 - 08 & 51 - 68 CL 00 - 08 & 51 - 68
CL 00 - 08 & 51 - 68 CL 00 - 08 & 51 - 68
2 3 4 5
(3) (4) (5) (6)
1 2 3 4
(3) (4) (5)
**Default Values are different for each user.
Refer to the SYS3316RF Programming
Worksheet at the end of this manual for
other user default values.
NOTE: Some programming locations allow
variable-length data and require an End-
of-Number (EON) character. Program
4 ("E") after the last digit. Fill
remaining unused Positions with "0".
The EON character is not required if the
last digit is in Position 6.
PROGRAMMING CONVERSIONS PROGRAMMING CONVERSIONS PROGRAMMING CONVERSIONS
PROGRAMMING CONVERSIONS PROGRAMMING CONVERSIONS
Hexadecimal Value Hexadecimal Value Hexadecimal Value
Hexadecimal Value Hexadecimal Value
A
B
C
D
E
F
#
E
#
(6)
Key Strokes Key Strokes
Key Strokes Key Strokes Key Strokes
0
1
2
3
4
5