GeoVision GV-VS04H Quick Start Manual
GeoVision GV-VS04H Quick Start Manual

GeoVision GV-VS04H Quick Start Manual

Hide thumbs Also See for GV-VS04H:

Advertisement

Quick Start Guide

GV-Video Server
Thank you for purchasing GV-Video Server (GV-VS04H / VS11 / VS12 / VS14). This guide
is designed to assist the new user in getting immediate results from the GV-VS04H / VS11 /
VS12 / VS14. For advanced information on how to use the GV-VS04H / VS11 / VS12 /
VS14, please refer to GV-Video Server User's Manual on Software CD/DVD.
© 2012 GeoVision Inc. All rights reserved.
1
Introduction
Welcome to the GV-Video Server Quick Start Guide. In the following
sections, you will learn about the basic installations and configurations of the
GV-Video Server (GV-VS04H / VS11 / VS12 / VS14). For a detailed user's
manual, see GV-Video Server User's Manual on the GV-Video Server
software CD/DVD.

Packing List

GV-VS04H / GV-VS14
● 3.5 mm Stereo to RCA Cable x 2
● AC Power Cord x 1
● Conical Anchor x 4
● Screw x 4
● GV-Video Server Software CD/DVD x 1
● GV-NVR Software CD/DVD x 1
Note: The DC Male-to-Male Cable is
used to power on the camera through
the GV-Video Server. You can also
optionally purchase three more DC
Male-to-Male Cables and one DC
1-Male to 4-Female Cable to power on
four cameras through the GV-Video
Server.
2012/09
English
VS04111214-QG-A
● DC Male-to-Male Cable x 1
● Power Adaptor x 1
● Wall Hook x 1
DC 1-Male to
DC Male-to-Male
4-Female Cable
Cable

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GV-VS04H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GeoVision GV-VS04H

  • Page 1: Quick Start Guide

    Server. 4-Female Cable Cable is designed to assist the new user in getting immediate results from the GV-VS04H / VS11 / VS12 / VS14. For advanced information on how to use the GV-VS04H / VS11 / VS12 / 2012/09 VS14, please refer to GV-Video Server User's Manual on Software CD/DVD.
  • Page 2 The GV-PA191 is designed to provide power to ● Conical Anchor x 4 the IP device through a single Ethernet cable. The GV-PA191 is only supported by GV-VS04H, ● GV-Video Server Software CD/DVD x 1 GV-VS12 and GV-VS14. ● GV-NVR Software CD/DVD x 1...
  • Page 3 The GV-Video Server can work with the Wiegand-interface card reader to send cardholder data to the central monitoring stations Center V2 and VSM, as well as GV-System (DVR). The following devices are only supported by GV-VS04H and GV-VS14. GV-Reader GV-Reader includes transmit-receive antenna and electronics.
  • Page 4 Name Function GV-VS11 Video Input 4 plugs for video inputs. Front View Rear View Speaker Output A plug for the speaker device. Audio Input Each plug is for 2 audio inputs. Default Button It resets all configurations to their factory settings.
  • Page 5 GV-VS12 Name Function USB Port 1 USB port for installing the portable storage Front View device. Speaker Output A plug for the speaker device. Audio Input 2 plugs for audio inputs. Video Input 2 plugs for video inputs. Power In A plug to power on the GV-Video Server.
  • Page 6: Installing On A Network

    These instructions describe the basic connections to install the GV-Video System Requirement Server on the network. Here we use GV-VS04H as an example to To access the Web interface of the GV-Video Server, it is required to use demonstrate the steps.
  • Page 7: The Web Interface

    Note: If your router does not support DHCP, the default IP address will be 192.168.0.10. In this case, it is strongly suggested to modify the IP address to avoid IP address conflict with other GeoVision IP device on the same LAN. For details, see 2.3 Changing the IP Address, GV-Video Server User’s Manual on the Software DVD.
  • Page 8: Upgrading System Firmware

    Upgrading System Firmware Name Function GeoVision will periodically release the updated firmware on the website. To load the new firmware into the GV-Video Server, read the important notes Play Plays live video. below and then follow the instructions. Stop Stops playing video.
  • Page 9: Restoring To Default Settings

    In this case, please contact your sales representative and send your device back to GeoVision for repair. For details on upgrading system firmware, see Advanced Applications, Chapter 6, GV-Video Server User's Manual on the software DVD.
  • Page 10 Directly on the GV-Video Server: GV-VS04H / GV-VS14 GV-VS11 GV-VS12 1. Press and then release the Reset button immediately. 2. Press and hold the Load Default button until all 3 LEDs (Power, Ready and Disk Full/Fault) are on. This may take about 30 seconds.
  • Page 11: Connecting Auxiliary Devices

    Connecting Auxiliary Devices GV-VS04H / GV-VS14 GV-VS11 The 16-pin terminal block, located on the rear panel, can be used to develop The terminal block on the rear panel of GV-VS11 provides one digital input applications for motion detection, event alerts via E-mail and FTP, center and output, an RS-485 interface and auxiliary power.
  • Page 12 User's Manual on the software DVD. White with Blue Stripe Digital In 1 Blue Digital In 2 Green Ground Orange RS-485 - White with Orange Stripe RS-485 + 9F, No. 246, Sec. 1, Neihu Rd., Neihu District, Taipei, Taiwan Tel: +886-2-8797-8376 Fax: +886-2-8797-8335 support@geovision.com.tw http://www.geovision.com.tw...

This manual is also suitable for:

Gv-vs12Gv-vs14Gv-vs11

Table of Contents