Installation Instructions - Belling 60VH User Instructions

Before connecting the model to the electricity network:
- control the data plate (positioned inside the appliance) to ascer-
tain that the voltage and power correspond to the network and
the socket is suitable. If in doubt ask a qualifi ed electrician.
- If the power supply cable is damaged, it must be replaced with
another cable or a special assembly, which may be obtained
direct from the manufacturer or from the Technical Assistance
Centre.
- This device must be connected to the supply network through
either a plug fused 3A or hardwired to a 2 fase spur protected
by 3A fuse.
2. Warning !
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the filters while the cooker
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood
D) Avoid free flame, as it is damaging for the filters and a
fire hazard
E) Constantly check food frying to avoid that the overheated
oil may become a fire hazard
F) Disconnect the electrical plug prior to any maintenance.
G) This appliance is not intended for use by young children
or infirm persons without supervision
H) Young children should be supervised to ensure they do
not play with the appliance
I) There shall be adequate ventilation of the room when the
rangehood is used at the same time as appliances burning
gas or other fuels
L) There is a risk of fire if cleaning is not carried out in
accordance with the instructions
This appliance conforms to the European Directive EC/2002/96,
Waste Electrical and Electronic Equipment (WEEE). By making
sure that this appliance is disposed of in a suitable manner, the
user is helping to prevent potential damage to the environment
or to public health.
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated
as domestic waste, but should be delivered to a suitable electric
and electronic appliance recycling collection point. Follow local
guidelines when disposing of waste. For more information on the
treatment, re-use and recycling of this product, please contact
your local authority, domestic waste collection service or the shop
where the appliance was purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by
specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II, therefore no
earth cable is necessary.
The plug must be easily accessible after the installation of the
appliance.
If the appliance is equipped with power cord without plug, a
suitably dimensioned omnipolar switch with 3 mm minimum
opening between contacts must be fi tted between the appliance
and the electricity supply in compliance with the load and current
regulations.
The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be at
least 65 cm.
If a connection tube composed of two parts is used, the upper
part must be placed outside the lower part. Do not connect the
cooker hood exhaust to the same conductor used to circulate
hot air or for evacuating fumes from other appliances gener-
ated by other than an electrical source. In the case of assem-
bly of the appliance in the suction version prepare the hole for
evacuation of the air.
• We recommend the use of an air exhaust tube which has the
same diameter as the air exhaust outlet hole. If a pipe with a
smaller diameter is used, the effi ciency of the product may be
reduced and its operation may become noisier.
• Warning: if the bulbs are not working, ensure that they are
screwed in fully.
• Installation
Prior to proceeding with the assembly operations (according to
the model that you have purchased), to facilitate handling of the
device, remove the grille as indicated in Fig. 5.
• The appliance is equipped with 2 air outlets, to be used in
accordance with your specifi c requirements: one is located on the
upper part of the appliance and the other at the rear (Fig. 1A).
The fl ange D, to which the air exhaust pipe is connected, and a
plug B, used to shut off the unused air outlet, are both supplied
with the product.
• This device may be installed in two diff erent ways:
1. Fixing the hood to the lower part of the wall cabinet
(Fig.2)
- Make 4 holes in the wall cabinet respecting the measurements
indicated in fi gures 2 A-2 C.
- Position the hood underneath the wall cabinet and fi x it into place
using 4 screws (not supplied) suitable for the type of cabinet.
2. Fixing the hood to the wall (Fig.2).
- Make 4 holes in the wall cabinet respecting the measurements
indicated in fi gures 2 A-2 B. - Hang the hood on the wall, using
the 2 holes H, align it in a horizontal position and fi x it defi nitively
to the wall using the two lower safety holes I (Fig. 2B). For the
various installations use screws and screw anchors suited to
the type of wall (e.g. reinforced concrete, plasterboard, etc.). If
the screws and screw anchors are provided with the product,
check that they are suitable for the type of wall on which the
hood is to be fi xed.
The hood is already prepared for the version with which it was
ordered. The versions may be:
- Extraction (Fig. 1A-3)
- Filter (Fig. 1B-4-7).
- If the hood is an extractor model, the lever C must be posi-
tioned as indicated in Fig. 3.
- If the hood is a fi lter model, the lever C must be positioned as
indicated in Fig. 4.
• Extractor version
The appliance expels the fumes through an outside wall or a
duct. It is necessary to buy a telescopic pipe in accordance with
the standards in use (infl ammable) and connect it to fl ange D
(Fig 1A). The fl ange D is supplied with the product and should
be fi xed above the air outlet hole of the hood as indicated in
Fig. 3.
• Filtering version
To transform an extractor hood version into a fi lter hood version,
- 12 -