1. Manuals
  2. Brands
  3. AeroWorks Manuals
  4. Toy
  5. ULTIMATE 20-300 ARF-QB
  6. Assembly manual

AeroWorks ULTIMATE 20-300 ARF-QB Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

100cc-120cc ULTIMATE 20-300
ARF-QB
(Quick Build)
ASSEMBLY MANUAL
AEROWORKS
4903 Nome St.– Denver, CO. 80239
www.aero-works.net
1

Advertisement

Table of Contents
loading

Related Manuals for AeroWorks ULTIMATE 20-300 ARF-QB

Summary of Contents for AeroWorks ULTIMATE 20-300 ARF-QB

  • Page 1 100cc-120cc ULTIMATE 20-300 ARF-QB (Quick Build) ASSEMBLY MANUAL AEROWORKS 4903 Nome St.– Denver, CO. 80239 www.aero-works.net...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page Aeroworks Contact Information …………………………………………………………………………. 3 Introduction / Warranty…………………………………………………………………………. ………. 4 Kit Contents………………………………………………………………………………………………… 5 Items Needed To Complete ……………………………………………………………………………….. 8 Tightening and Re-shrinking The Covering ………………………………………………………………13 Ultracote™ Colors…………………………………………………………………………………………. 14 Checking Seams and Color Overlaps for Good Seal / Sealing Hinge Gaps ………..………………….. 15 Checking Hinges for proper throw ………………………………………………………………………..

  • Page 3: Aeroworks Contact Information

    Further, Aeroworks reserves the right to change or modify this limited warranty without notice. In that Aeroworks has no control over the final assembly or materials used for final as- sembly, No liability shall be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product.

  • Page 4: Introduction / Warranty

    LIMITED WARRANTY READ! It is important to notify Aeroworks of any damage or problems with the model within 30 days of receiving your airplane to be covered under warranty. If you wish to return this air- craft for any reason a 15% restock fee will be charged to the customer. In addition the cus- tomer is responsible for all return shipping cost and all prior shipping cost will not be re- funded.

  • Page 5: Kit Contents

    KIT CONTENTS cut air exit slots pre installed with (4) 100cc-120cc Ultimate Parts List T2.6x10mm PWA screws (1) Rear Long Pipe fuse bottom hatch cover with pre cut slots for stinger exit BASIC AIRCRAFT PARTS: (2) Bottom wing fillet installed – Left and Right, painted Fuselage –...
  • Page 6 Right Top Wing with Aileron – covered: (2) 8-32 blind nuts installed for the Outer struts (2) Aluminum Main Landing Gear, 1 left and 1 right, mounting. painted (2) 2mm steel L bracket – outer struts fitting prein (2) 5mm dia. x 48mm AL Axle stalled at the root of the wing (2) M8 lock nuts (8) pin point hinges glued...
  • Page 7 (2) 4-40x36mm left hand and right hand threaded #12: pushrod for connecting rudder servo (1) 23x740mm Carbon Compound top wing tube (4) 4-40 ball links for connecting rudder servo (1) 23x740mm Carbon Compound bottom wing (2) 4-40x20mm hex head bolts for connecting rudder tube with hard wood rod inside and pre-drilled servo for mounting...

  • Page 8: Items Needed To Complete

    1 - 26x12-28x10 2 Blade Propeller ◊ 1 - 27x12-28x12 2 Blade Propeller Note: DLE 111 can be purchased through Note: DA 120 can be purchased through Aeroworks. Aeroworks. Engine Option 2: DA 100-L ◊ 1 - DA 100-L ◊...
  • Page 9 HARDEWARE NEEDED TO COMPLETE Exhaust Option 3: Tuned Pipes Exhaust Option 1: Compact Mufflers ◊ ◊ 2 - MTW RE-2 Tuned Pipes 1 - Left Compact Muffler ◊ ◊ 2 - 70mm Drop Headers 1 - Right Compact Muffler ◊ ◊...
  • Page 10 Hitec 7940TG Servos may be used for sport flying. ◊ 1 - 4” Spinner- Carbon Fiber Recommended If flying more aggressive aerobatics please see servo option two below. Note: Spinner available from Aeroworks Note: Servos available through Aeroworks ◊ 8 - Hitec 7940TG Servos for flight surfaces ◊...
  • Page 11 HARDEWARE NEEDED TO COMPLETE Receiver Power System : Recommended Extensions: 22 AWG extensions are recommended through out The Aeroworks 100-120cc Power package is the 100cc Ultimate. The following sizes will be recommended. The package consists of the used: following items: ◊...
  • Page 12 BUILDING ACCESSORIES NEEDED TO COMPLETE Adhesives Tools • 15-30 Minute epoxy • • Blue Loctite Allen wrenches US and Metric. • • Epoxy mixing cups, mixing sticks, brushes Dremel cutting disc and sanding drum tool • • CA kicker (optional) Electric drill and selection of bits •...

  • Page 13: Tightening And Re-Shrinking The Covering

    TIGHTENING AND RE-SHRINKING THE COVERING 1. Open your kit slowly and take care not to dam- 3. If bubbles persist, use a small pin to punch holes age any parts of the kit. Remove all parts from in the bubble to relieve trapped air and reheat. their plastic protective covers for inspection.

  • Page 14: Ultracote™ Colors

    Ultracote™ Colors 1. Your model is covered with Ultracote™ covering. In case of repairs, the colors are: Red/Yellow/Black Scheme Black #874 Silver #881 True Red #866 Bright Yellow #872 Yellow/Silver/Blue Scheme Pearl Blue #845 Silver #881 Cub Yellow #884 White #870...

  • Page 15: Checking Seams And Color Overlaps For Good Seal Sealing Hinge Gaps

    It is the responsibility of the purchaser / operator to check the covering seams and overlaps for security and a good seal. Aeroworks is not responsible for failure of covering seams or overlaps during flight. Note: If covering continues to lift apply a small amount of thin CA underneath the covering.

  • Page 16: Checking Hinges For Proper Throw

    CHECKING HINGES FOR PROPER THROW If the elevator hinges are tight follow the IMPORTANT same process as described for the wings. If control surfaces will not throw to full deflec- tion it may be necessary using a heat gun to Note: Once these steps have been completed apply heat to the knuckle of each hinge.

  • Page 17: Checking Glue Joints

    CHECKING GLUE JOINTS 1. Go over all seams and glue joints with thin CA, this will ensure your model lasts for many sea- sons to come. Note: Even if you can visibly see glue on all glue joints it is still recommended that the joints be reglued.

  • Page 18: Canopy/Front Hatch Warp Prevention

    CANOPY/FRONT HATCH WARP PREVENTION 1. Leave the canopy bolted to the airframe at all times unless working on the inside of the fuse. Due to high humidity levels during the building and shipping process the canopy may warp when not bolted to the airframe. 2.

  • Page 19: Wing Assembly

    4. Pull the servo lead through the root end of the wing. 2. Attach the 12” servo extension to the servo wire and secure using an Aeroworks Safety Clip. Minimum recommended servo: 181 in. oz. / Metal Geared / Digital...
  • Page 20 Install servo in servo well with the output shaft Assemble pushrod and control horn toward the leading edge of the wing. assembly as shown. The ball link goes between the left and right sides of the control horn sides and is secured with a nylon lock nut. Improperly installed servo linkages can cause ser- vos to strip and ailerons to flutter.
  • Page 21 Align the control horns over the factory Plug the servo into the receiver and turn on. drilled holes. Ensure servo is centered and the servo arm is parallel to the aileron hinge line. Adjust the Note: Control horns have been set at a slight length of the pushrod so that the aileron is at offset to allow for maximum torque at full the neutral position when the servo arm is par-...
  • Page 22 3. Install mounting bracket using mounting bolt Outer Strut and washer as shown below. Mounting Bracket Installation 4. Wing assembly is now complete. 1. Gather the outer strut mounting brackets as shown below. Note: Check mounting bolts are tight before each ◊...

  • Page 23: Stab And Elevator Assembly

    ◊ 1 - Adjustment wrench 2 - 48” servo extension ◊ 2 - Aeroworks Safety Clips Note: 48” servo extension will be used to connect servos to receiver during a later step. 2. Correct installation of ball link, flat washer and 2.
  • Page 24 3. Assemble the pushrod and control horn assem- Use thick CA on each screw prior to installing bly as shown. The ball link goes between the to lock screws in place left and right sides of the control horn sides and is secured with a nylon lock nut.

  • Page 25: Rudder And Rudder Servos Installation

    RUDDER AND RUDDER SERVOS INSTALLATION Mix epoxy in mixing cup and use a tapered Rudder Installation stick to apply the epoxy inside the pre-drilled holes in the trailing edge of the fin. Apply Gather the rudder, hinges, epoxy, Vaseline, epoxy to one side of each hinge and insert the stir sticks, mixing cup and alcohol as shown.
  • Page 26 Ensure there is minimal to no gap between fin Mix epoxy in mixing cup and use a tapered and rudder. Allow epoxy to fully cure. stick to apply the epoxy inside the pre-drilled holes in the leading edge of the rudder. Apply Note: Ensure you have full rudder deflection epoxy onto each hinge.
  • Page 27 2. Assemble the ball links between the control 4. Use thick CA on each screw prior to installing to horns as shown. Secure with nylon lock nut. lock screws in place Note: Mount ball link to inner control horn hole Note: CA glues have a fast drying time.
  • Page 28 9. Install the servo arms to servos as shown below. Assemble rudder coupler pushrods and adjust pushrod length to fit between servo arms. 7. Attach Y harness to rudder servos as shown be- low. Use an Aeroworks safety clip to secure the connection.
  • Page 29 10. Install the ball link onto the threaded coupler as 12. Install the coupler assembly onto the rudder ser- shown below. vos as shown, small adjustments may be neces- sary to allow the coupler to fit properly. 11. Assemble the rudder servo coupler. Use (2) 13.
  • Page 30 14. Tie off or tape rudder cables to keep them from 16. Insert rudder cable through the brass swage tube pulling into fuse. as shown. 15. Pull the rudder cables from the fuse tail to the 17. Thread cable through the threaded coupler hole, rudder servo tray.
  • Page 31 18. Loop the cable back through the brass swage 20. Cut off excess cable as shown. tube and pull tight as shown. 19. Crimp the brass tube with a crimping tool or pli- 21. A drop of thin CA may be applied to the swage ers.
  • Page 32 22. Repeat above steps for the other side rudder ca- 24. Plug the rudder servo Y harness into the rudder ble. channel of the receiver and power up. Turn on transmitter to center rudder servos. 25. Attach aft servo arm to servo and leave the front coupler disconnected until final radio program- ming is done.

  • Page 33: Tail Wheel Installation

    TAIL WHEEL INSTALLATION 1. Tape the rudder to the vertical fin in the neutral 3. Place tail wheel steering tiller over the pre- position as shown. This ensures the rudder is drilled holes in the bottom of the rudder. straight when the tail wheel steering springs are installed.
  • Page 34 5. Mount the tail wheel steering tiller using two 7. Place a drop of thick CA on tail wheel strut wood screws. mounting screws before inserting in the pre- drilled mounting holes on the bottom rear of the fuse. 8. Mount the tail wheel strut using three wood screws.
  • Page 35 10. Use pliers to twist spring ends closed around the 12. Repeat for opposite side tail wheel spring. Ad- rudder and tail wheel tillers. just length and spring tension so that tail wheel is centered when rudder is centered. 13. Tail wheel final assembly is complete. 11.

  • Page 36: Main Landing Gear And Wheel Pant Installation

    MAIN LANDING GEAR AND WHEEL PANT INSTALLATION Main Landing Gear Installation 3. Slide the gear into the fuse as shown below. Gather the landing gear parts as shown below. ◊ 2 - Aluminum landing gear struts ◊ 2 - 4” Foam Tires ◊...
  • Page 37 5. Bolt landing gear strut to fuse with (4) 8-32 bolts 7. Check alignment of axle with cutout in wheel and washers. pant. Check alignment of wheel pant mounting holes with mounting holes in gear. Securely tighten axel to gear strut. 6.
  • Page 38 9. Install outer wheel collar. Use blue Loctite on 12. Repeat above steps for other wheel and wheel the wheel collar set screw before final tighten- pant. ing. 10. Slide the lock washer then the flat washer on the wheel pant mounting bolts. Use blue Loctite on the bolts before final tightening.

  • Page 39: Engine Installation

    ENGINE INSTALLATION 3. Locate the laser cut engine mounting template Engine Installation for the DA-120. 1. The 100cc-120cc Ultimate will accept a wide Note: If other engines are used the templates may range of engine types. Illustrations for a DA- be modified to fit you engine selection.
  • Page 40 5. Align mounting template with firewall and tape 7. Insert the (4) bolts through the engine mount and in place. install the engine standoffs and fender washers. Required distance from front of firewall to prop hub is 7 1/16”. Use correct amount of spacers and washers to achieve this distance.

  • Page 41: Throttle Servo Installation

    9. Use fender washers and lock nuts to secure the Throttle Servo Installation engine to the firewall. Remember to tighten the bolts in a cross pattern to prevent crushing the 1. Gather the left and right plywood throttle and firewall. choke servo mounting trays, the throttle and choke servos and pushrod parts.
  • Page 42 3. If standard style mufflers are to be used, install 5. Use a rotary cutting tool to cut out the throttle the standard mufflers to the engine cylinder servo mounting hole. heads. Attach the throttle pushrod to the engine throttle arm as shown. Layout the location of Note: Cover engine with a towel or cloth or use the throttle servo and throttle pushrod.
  • Page 43 7. With the servo arm centered and the throttle arm 9. Gather the soldering tools as shown below. of the carburetor at half throttle, measure and mark the end of the throttle pushrod wire that Note: For best results we recommend a high will be inserted into the threaded coupler as quality Silver Solder like “Sta-Brite”...
  • Page 44 11. Attach the throttle pushrod with the 4/40 ball 13. Use a drop of thick CA on the throttle servo links and secure. Power up the receiver and mounting screws after they have paced through throttle servo and adjust pushrod for proper op- the motor box floor as shown below.
  • Page 45 15. Attach 4-40 ball link and threaded rod to throt- 17. Install the throttle pushrod to the engine throttle tle servo arm. arm as shown. 16. Cut 4-40 rod and carbon rod to correct length Slip the carbon rod over the 4-40 threaded pushrod.

  • Page 46: Standard Muffler Installation

    STANDARD MUFFLER INSTALLATION 1. Gather the standard muffler parts as shown be- 3. Use a drop of blue Loctite on muffler bolts be- low: fore installation. ◊ 1 - Left Compact Muffler ◊ 1 - Right Compact Muffler ◊ 4 - Muffler Mounting bolts ◊...

  • Page 47: Canister Muffler Installation

    CANISTER MUFFLER INSTALLATION 3. Use a sealing iron to ensure the covering is 1. Gather the canister items shown below: bonded to the bottom of the fuse frame around ◊ the pre cut hot air exit holes. 2 - MTW TDH 75 Rear Exit Canisters ◊...
  • Page 48 5. Finished canister air exit holes shown below. 7. Use 30 Minute epoxy to secure the canister mount as shown. Note: Reseal all edges with a covering iron to prevent fuel from soaking into the wood. 6. Correct location of canister mount shown below. 8.
  • Page 49 9. Finished canister installation shown below. 11. Reinstall the tunnel hatch covers as shown be- low. 10. Install headers using the supplied gasket or high 12. It may be necessary to install teflon extensions temp silicon gasket material and securely bolt to to the canister stingers as shown below.

  • Page 50: Tuned Pipe Installation

    TUNED PIPE INSTALLATION 1. Gather the tuned pipe items shown below: 3. Remove covering over the precut air exit holes in both the front and rear hatch covers as shown ◊ 2 - MTW RE-2 Tuned Pipes below. ◊ 2 - 70mm Drop Headers ◊...
  • Page 51 5. Finished pipe air exit holes shown below. 7. Correct location of tuned pipe mount shown be- low. Test fit mount inside tunnel before continu- Note: Reseal all edges with a covering iron to ing, it may be necessary to lightly sand the edges prevent fuel from soaking into the wood.
  • Page 52 9. Install the teflon coupler and clamp onto the 11. Install headers using the supplied gasket or high tuned pipe at this time. Slide the pipe into the temp silicon gasket material and securely bolt to tunnel and through the mounting bracket as cylinder heads as shown.

  • Page 53: Ignition Module Installation

    IGNITION INSTALLATION 3. Position the ignition module inside the engine 1. Gather the supplied mounting hardware to be box to allow both of the spark plug leads to exit used. Included in the kit are large and small ny- and properly connect to the engine without ex- lon ties, One Wrap Velcro ties, and foam rubber cess tension or chafing.
  • Page 54 8. Thread ignition connector through firewall and 6. Install the ignition module and the foam pad connect ignition timing connectors with with a nylon tie as shown. Aeroworks Safety Clip. Ensure the connectors will not come apart from vibration or light ten- sion.
  • Page 55 9. Connect the ignition cutoff, regulator, and bat- 11. Using a small piece of hook and loop material, tery as shown below. secure the Smart-Fly ignition regulator to the fuse floor. 10. Using a nylon tie, install the ignition battery as 12.
  • Page 56 13. Using another piece of hook and loop material, install the Rcexl ignition cutoff as shown below. 14. Install the MPI Ignition switch as shown below. Install the Rcexl cutoff light on the fuse side at this time.

  • Page 57: Inner Cabane Installation

    INNER CABANE INSTALLATION 1. Remove the rear inner cabane mounting bolts as Remove the rear cabane as shown below. shown. 2. Remove the 4-40 mounting bolt on the rear ca- 4. Slide the male end of a 18” extension through bane as shown below.
  • Page 58 7. Reinstall the center cabane as shown below. 5. Route the extension into the fuse and reinstall the rear cabane at this time. 6. Use blue loctite on the cabane mounting bolt as shown below. Reinstall the mounting bolts at this time.

  • Page 59: Fuel Tank Assembly And Installation

    FUEL TANK ASSEMBLY AND INSTALLATION 3. Assemble the fuel pick up line, rubber stopper Fuel Tank Assembly and metal end caps. 1. Gather the fuel tank parts as shown below. There are two tanks provided, 1000cc (32oz) for your fuel system and 750cc (24oz) for your smoke system if used.
  • Page 60 5. Final assembly of rubber fuel stopper with fuel 7. Install the fuel tubing and clunk. Secure the fuel pick up tube shown below. tubing with nylon ties to the pick-up tube and clunk. 6. Install air vent tube into rubber stopper and bend 8.

  • Page 61: Fuel Tank Installation

    Note: The fuel “T”, fuel filter and filler dot are not supplied, but are available through Aeroworks. 10. If using both the fuel and smoke tanks position 2. Install a short piece of fuel line and the fuel “T”...
  • Page 62 3. Install the fuel filter, fuel filler line and carbure- 5. Thread nylon ties under tank mounting plate and tor fuel line to the fuel tank. Be sure to leave center in position. Install foam rubber pad for enough fuel line to reach the engine carburetor fuel tank to rest on.
  • Page 63 7. Route the line to the engine carburetor out of the 9. Install fuel filler dot as shown below. bottom of the engine box. Use rubber grommet where the fuel line goes through the plywood to Note: Install the fuel dot above the tank center line, prevent fuel line chafing.

  • Page 64: Receiver/Battery Installation

    RECIEVER/BATTERY INSTALLATION 3. Install the switches on either side of the fuse. 1. Gather the supplied mounting hardware to be Final switch installation will be up to the used. Included in the kit are large and small ny- builder. lon ties, One Wrap Velcro ties, and foam rubber pads as shown, 2.
  • Page 65 5. Use the foam mounting pads supplied with the 7. Gather the following regulator installation items kit to protect batteries from vibration. as shown below: ◊ 1 - Fromeco Sahara regulator w/ Deans ◊ 1 - 1.5” Plywood mounting plate- Not Supplied ◊...
  • Page 66 9. Place plywood mounting plate in fuse and allow 11. Place hook and loop material on mounting plate CA to fully cure. and allow CA to fully cure. . 10. Apply thick CA to the adhesive side of the hook 12.
  • Page 67 13. Install regulator in fuse as shown below. Repeat 15. Route the lower aileron extensions out of the previous steps for the remaining regulator. fuse as shown below. 14. Install the receiver using Velcro strap and foam pad as shown below.

  • Page 68: Cowl Installation For Standard Mufflers

    COWL INSTALLATION-STANDARD MUFFLER 1. Gather the following material for making a cowl 3. Measure and mark a center line on bottom of cutout template. fuse as shown below. Hobby Knife, Ruler, Tape, Felt tip pen or marker Template material has been supplied. Note: The following steps are if you are using standard style mufflers.
  • Page 69 5. Use a T-Pin to mark the location of the cowl 7. Install the bottom 4-40 cowl mounting bolts as mounting bolts as shown below. shown below. 6. Use an x-acto knife to enlarge the mounting 8. Mark the template “Cowl Side” for easy holes as shown.
  • Page 70 9. Lift the template material so that it contacts the 12. Extend the outline of the holes approximately bottom of the muffler exhaust stacks. Trace the 3 1/4” as shown below. location of the exhaust stack exit holes. 13. Cut out the holes on the paper template and rein- 10.
  • Page 71 Always check the operating temperature of your engine to prevent any damage from occurring. Aeroworks is not responsible for damages incurred from improper engine cooling. Allowing hot air to pass through tunnel in- creases air flow and provides increased en- gine cooling.

  • Page 72: Cowl Installation For Canister/Tuned Pipes

    Always check the operating temperature of your engine to prevent any damage from occurring. Aeroworks is not responsible for damages incurred from improper engine cooling.

  • Page 73: Manual Choke Installation

    MANUAL CHOKE PUSHROD INSTALLATION 3. Use supplied rubber grommet and install in cowl 1. Gather the choke pushrod and ball link assembly for professional look. shown below. Measure the length of the choke pushrod required to extend out of the front of the cowl when the choke control arm is fully pushed aft.

  • Page 74: Preflight Preparation

    2. Insert wing tubes as shown, ensure the predrilled 4. Slide the wing tubes into the fuse as shown, se- mounting holes are facing toward the top of the cure aileron extension with Aeroworks Safety wing. Clip.
  • Page 75 5. Secure the tubes in the wing with the provided 7. Gather the wing mounting bolts as shown, there 6-32 mounting bolts. are two lengths of mounting bolts the (2)longer bolts are for the center cabane and the (8) shorter bolts are for the outer cabanes.
  • Page 76 9. Slide the right top wing panel onto the wing and 11. Secure outer cabanes with 8-32 x 10mm bolts, alignment tubes and slide wing panels together. flat washer and lock nut. Note: Outer struts have been pre-marked LB (left bottom) and RB (right bottom) for easy refer- ence.
  • Page 77 16. Secure top section of cowl with 6-32 x 16mm 14. Slide the rubber backed washers on the hatch hex head bolts and #6 bonded washers. mounting bolts and insert bolts through the hatch mounting holes and into the fuse blind nuts. Tighten snugly but do not over tighten and crush the hatch or the fuse sides.
  • Page 78 18. Secure top hatch using 4-40 button head bolts and bonded washers.

  • Page 79: Center Cabane Fairing Installation

    CENTER CABANE FAIRING INSTALLATION 1. Locate the Center Cabane Fairing Installation 3. Lower the top wing onto center cabane. items as shown below: ◊ 1 - Center Cabane Fairing ◊ 2 - 8-32x40mm Mounting Bolts ◊ 2 - 8-32 Lock Nuts ◊...
  • Page 80 5. Slide bolt through cabane fairing as shown. The 7. Install #8 bonded washer followed by a lock nut 9mm spacer should pass through faring and sit and tighten as shown. flat against the center cabane. 8. Top view of 9mm spacer installation with wing 6.

  • Page 81: Decal Installation

    DECAL INSTALLATION 3. Placement of optional decal package shown, in- 1. Decals supplied with the kit will vary from the cluded decals will differ. photos below. Decal application steps will be similar. Gather supplied decals, transfer tape, ruler, scis- sors, hobby knife, plastic squeegee or credit card, Windex or Application fluid like Rapid Tac.
  • Page 82 6. Remove backing from Clear transfer tape. 4. Placement of optional decal package shown, in- cluded decals will differ. 5. Cut transfer tape to accommodate decal size. 7. Apply clear transfer tape over top of decal. Note: Transfer tape will be reused. DO NOT throw away any transfer tape until decal placement is complete.
  • Page 83 8. Press transfer tape to top of decal. 10. Spray model surface with application fluid, Windex or soapy water solution. 9. Peel backing from decal. 11. Spray back side of decal with application fluid, Windex or soapy water solution.
  • Page 84 12. Position decal in proper location. Application 14. Pull transfer tape from top of decal. Take care fluid will allow decal to be moved slightly. not to pull away or damage decal. 13. Using a plastic squeegee or credit card. Spread de- 15.

  • Page 85: Center Of Gravity / Control Throws

    CENTER OF GRAVITY - CONTROL THROWS Start at recommended CG until you are com- Center of Gravity fortable with the flight characteristics of the Warning, DO NOT skip this step! aircraft. You may find this a bit nose heavy at first but that is fine to start with.
  • Page 86 2. Elevator throw measured in inches at the widest 4. Elevator throw measured in degrees. Locate point of the elevator throw meter at widest point of the elevator. 3. Use the supplied flight control deflection meter 5. Aileron throw measured in degrees at widest .
  • Page 87 6. Measure the rudder deflection in inches from bottom of the rudder...

  • Page 88: Control Throw Deflection Table

    Control Throw Deflection Table Low Rate Medium Rate Aileron 1 1/4” or 11˚ up 1 1/2” or 25˚ up 1 1/4” or 11˚ down 1 1/2” or 25˚ down Rudder 4” left 6” left 4” or right 6” right Elevator 1 1/2” or 14˚ up 4 ”...

  • Page 89: Preflight Check List

    Preflight Check List Range check: Do a range check with and without Center of Gravity: Check CG is set properly. the engine running in accordance with the radio manufacturer instructions. If there is insuffi- Engine: The engine should run smoothly at all cient range or a large reduction with the engine throttle settings with smooth transition from running, do not fly until it is resolved!
  • Page 90 Spins upright and inverted • Flat Spins upright and inverted • Harriers upright and inverted • Water falls • Torque Rolls • Rolling circles • Rolling harrier The sky and your imagination are you only limits. FLY and ENJOY! AEROWORKS World Class Aircraft...

  • Page 91: Optional Accessories

    Accessories Available From Aeroworks For more information or to order accessories visit our website: WWW.AERO-WORKS.NET or call Aeroworks at: (303) 371-4222 Custom Wing/Stab Bags Optional Decal Package Yellow/Blue Designed especially for 100cc-120cc Ultimate Made using high quality printed vinyl these decals aircraft.
  • Page 92 Aeroworks Custom Pilots Ultimate 20-300 Dash Panel The optional 3 dimensional dash panel from Aeroworks line of custom pilots add great looks to Aeroworks adds that finished look to any cockpit. your model with minimal weight gain. A must for This dash panel is specifically designed to fit the any I.M.A.C pilot or for anyone to dress up their...
  • Page 93 Accessories Available From Aeroworks For more information or to order accessories visit our website: WWW.AERO-WORKS.NET or call Aeroworks at: (303) 371-4222 Aeroworks Carbon Landing Gear Ultimate 20-300 Stick Plane The Ultimate 20-300 Stick plane is an accurate rep- Save weight and increase strength with the optional lica of the 100cc-120cc Ultimate.
  • Page 94 Ultimate 20-300 CUSTOMER NOTES ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ ___________________________________________________________________________ __________________________________________________________________________...

Table of Contents