Related Manuals for The Handy THMC-A
Summary of Contents for The Handy THMC-A
- Page 1 OPERATOR’S MANUAL AND PARTS LIST PETROL MULTI CUTTER - THMC-A Spares & Support: 01793 333212 www.thehandy.co.uk Before use please read & understand this manual, paying particular attention to the safety instructions. 30/04/2013...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS SPECIFICATIONS FUEL MAJOR PARTS ASSEMBLY 8-12 REPLACEMENT OF SPOOL, LINE AND CHAIN 13-14 OPERATION MAINTENANCE TROUBLE SHOOTING PARTS DIAGRAMS AND LISTS 18-22 EC DECLARATION OF CONFORMITY Page 2... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS Read and understand the owner’s manual and labels affixed to the machine. Learn its application and limitations as well as the specific potential hazards. Retain these instructions for future reference. Use sturdy footwear and a helmet with eye and ear protection. Protect exposed parts of your body. -
Page 4: Specifications
SPECIFICATIONS MODEL THMC-A Engine Displacement 25.4cm³ Max Output Power .Z PLQØï Fuel Tank Capacity 0.6L Bore and Stroke 34 x 28mm Fuel Type Unleaded Fuel Mixture Unleaded Petrol/Oil 25:1 Mineral Oil (see below for synthetic) Equivalent Spark Plug Champion RCJ6Y or NGK BPMR7A... -
Page 5: Fuel
FUEL 3HWURO LV YHU\ ÀDPPDEOH Do not use or IXHO WKH multicutter near a ÀDPH, VSDUNV or while smoking $OORZ WKH HQJLQH WR FRRO EHIRUH UHIXHOOLQJ )XHO WKH HQJLQH DW OHDVW P DZD\ IURP \RXU ZRUN DUHD se a ratio of 25:1 unleaded petrol to mineral oil. Mix well in an ‡... -
Page 6: Major Parts
MAJOR PARTS DIAGRAM Page 6... - Page 7 MAJOR PARTS LIST Engine head Hexagon socket head screw with washer --- 4pcs Safety level Hex Nut M5 ---4 pcs Ignition switch Line trimmer shield Strap hanger Brush cutter metal guard Carry strap Line trimmer impeller Coupler Allen key Rotating knob Spark plug spanner Line trimmer head Chain tension spanner...
-
Page 8: Assembly
ASSEMBLY 0RGHUQ SURGXFWLRQ WHFKQLTXHV PHDQ WKDW WKHUH LV YHU\ OLWWOH OLNHOLKRRG RI WKHUH EHLQJ DQ\ SDUWV PLVVLQJ LQ WKH FDUWRQ VXSSOLHG +RZHYHU SOHDVH FKHFN WKH ER[ FDUHIXOO\ EHIRUH FRPPHQFLQJ DQ\ DVVHPEO\ If you are missing any parts please call our spares helpline: 01793-333212. Contents: Power Unit;... - Page 9 ASSEMBLY, cont’d +HGJHWULPPHU $WWDFKPHQW ‡ To adjust the angle of the hedgecutter, depress levers A and B as shown above and rotate the hedgecutter to the desired angle. 2SHUDWLQJ WKH +HGJHWULPPHU ‡ $OZD\V KDYH D ¿UP IRRWLQJ DQG XVH WZR KDQGV ‡...
- Page 10 ASSEMBLY, cont’d Brushcutter Attachment: Fig. 1 Remove the Blade Nut, this nut has a left hand thread so should be turned clockwise to undo it. Fig. 2 Remove the Cupped Washer, Clamp Washer and Flanged Washer. Fig. 3 Remove the 3 Blade Guard Screws with the Allen key. Fig.
- Page 11 ASSEMBLY, cont’d 2SHUDWLQJ WKH %UXVKFXWWHU ‡ Operate the throttle trigger with your right hand and hold the barrier handle with your left hand. ‡ Always kHHS D ¿UP JULS ZLWK ERWK KDQGV GXULQJ RSHUDWLRQ ‡ The brushcutter should be held at a comfortable position with the trigger handle about hip height.
-
Page 12: Assembly
ASSEMBLY, cont’d Line Trimmer Attachment: ‡ 6OLGH WKH VKLHOG RQWR WKH DWWDFKPHQW VKDIW DQG ¿W RYHU the bracket, as in Fig. 11. ‡ Fix the bolt through the holes in the tabs on the shield and the slots in the bracket on the attachment shaft. ‡... -
Page 13: Replacement Of Spool, Line And Chain
REPLACEMENT OF SPOOL AND LINE To replace the line or spool: ‡ Stop the engine. ‡ /D\ WKH WULPPHU RQ WKH ÀRRU VR WKDW WKH FXWWLQJ KHDG LV IDFLQJ XS ‡ Remove the bump knob/retaining cap by turning it anti-clockwise. ‡... - Page 14 REPLACEMENT OF PRUNER CHAIN Remove the sprocket wheel cover. • Remove the guide bar and chain. • Remove the old chain and replace with the new chain. • Mount the guide bar and then fit the saw chain around the bar and sprocket, paying particular •...
-
Page 15: Operation
OPERATION 6WDUWLQJ WKH 0XOWLFXWWHU ‡ Place the machine on the floor, as this may make it easier to start. Move the ignition switch to the “on” or I position (see Fig. O). • ‡ Move the choke lever upwards to the “start” position (for cold start only) (Fig. P). ‡... -
Page 16: Maintenance
MAINTENANCE 7KH HQJLQH RI WKH PXOWLFXWWHU PXVW EH DW D FRPSOHWH VWRS GXULQJ DVVHPEOLQJ FOHDQLQJ DQG DQ\ PDLQWHQDQFH WKDW PD\ EH QHFHVVDU\ $LU )LOWHU $FFXPXODWHG GXVW LQ WKH DLU ¿OWHU ZLOO UHGXFH HQJLQH HI¿FLHQF\ LQFUHDVH IXHO FRQVXPSWLRQ and allow abrasive particles to pass into the engine. 5HPRYH DQG FOHDQ WKH DLU ¿OWHU UHJXODUO\ WR HQVXUH RSWLPXP SHUIRUPDQFH ‡... -
Page 17: Trouble Shooting
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Power loss or sudden Fuel Tank is empty. Add fuel. stopping. Mixture not reaching Drain and rinse out fuel carburettor. system. Water in the mixture. Clean fuel filter. The air filter is dirty. Clean air filter. Carbon deposits in Clean all affected parts cylinder, exhaust pipe... -
Page 18: Parts Diagrams And Lists
PARTS DIAGRAM AND LIST - ENGINE Part No Desc Qty No Part No Desc TH132-1 Screw TH132-25 Flat Washer TH132-2 Spring Washer TH132-26 Heat Shield TH132-3 Flat Washer TH132-27 Exhaust TH132-4 Filter Housing TH132-28 Exhaust Gasket TH132-5 Carburettor TH132-29 Clips TH132-6 Gasket TH132-30... - Page 19 PARTS DIAGRAM AND LIST - LINE TRIMMER (THLTATT) Line Trimmer Parts: Part No Description TH131-2 Bracket TH131-3 Screw TH131-4 TH131-6 Spool & Cap Assembly TH131-7 Shield TH131-8 Knob TH131-9 Washer Page 19...
- Page 20 PARTS DIAGRAM AND LIST - BRUSHCUTTER (THBCATT) Part No Description TH130-1 Shield TH130-2 Flat Washer TH130-3 Spring Washer TH130-4 Screw TH130-5 Blade Boss Outer TH130-6 Nut Cover TH130-7 Lock Nut (Left Hand) TH130-8 Blade Boss Inner Page 20...
- Page 21 PARTS DIAGRAM AND LIST HEDGETRIMMER (THHCATTA) Part No. Description Qty. TH185-1 Shaft assembly TH185-2 Hexagon socket bolt TH185-3 Flat washer TH185-4 Spring washer TH185-5 Hexagon socket bolt & spring washer TH185-6 Hedge trimmer head TH185-7 Blade cover TH185-8 End clamp Page 21 ...
-
Page 22: Parts Diagrams And Lists
PARTS DIAGRAM AND LIST - PRUNER (THPATT) Part No Description TH129-1 Oil Filler Cap Oil Tank Assembly TH129-3 TH129-4 Chain HP-166 TH129-5 Chain Bar TH129-6 Chain Bar Cover TH129-7 TH129-8 Chain Cover TH129-9 Chain Tension Adjuster Assy Page 22... - Page 23 PARTS DIAGRAM SHAFT AND D.HANDLE Part No Description TH142-1 Hand Wheel TH142-2 Coupling TH142-3 Throttle Lock TH142-4 Throttle Trigger TH142-5 Handle Left Side TH142-6 Handle Right Side TH142-7 Safety Throttle Trigger TH142-8 On/Off Switch TH142-9 D.Handle Page 23...
-
Page 24: Ec Declaration Of Conformity
Handy Distribution Ltd. SN3 4NS Declare that the product Designation: 25cc 4 IN 1 Multi Cutter Model: THMC-A Complies with the following directives: 2006/42/EC- Machinery Directive 2004/108/EC- Electromagnetic Compatibility Directive 2002/88/EC- Engine Emissions Directive The conformity assessment procedure followed was in according with Annex V of the Directive 2000/14/EC.