Kinroad XT50QT-5 User Manual

Hide thumbs

Table Of Contents

Enlarged version

：

FOREWORD

Thanks for your purchasing this motorcycle.

With the help of this manual, you will learn the

correct procedures of operation and basic knowledge of

maintenance and trouble shooting of the motorcycle. It

presents all the basic knowledge of maintenance and

trouble shooting of the motorcycle. It presents all

the details of the performance of this motorcycle to

you and the vehicle will make your life more relaxed

and happier.

In case any picture does not agree with the vehicle

physically, the latter shall prevail.

CAUTION． NOTE and MAIN POINTS

ings and should be carefully reviewed．

!CAUTION

：The personal safety of the rider may be

involved，disregarding this information could result in

injury to the rider．

NOTE

： These instructions point out special service

procedures or precautions that must be followed to

avoid damaging the machine．

MAIN POINTS

： This provides special information to make

maintenance easier or important instructions clearer．

carry special mean-

VIN AND ENGINE SERIAL NUMBER LOCATION

your dealer when ordering parts or special service

information.

The VIN is stamped on the front main beam of the

frame．

of the crankcase assembly

VIN. :

- 1 -

The VIN and/or engine serial number are used to

The engine serial number is stamped on the rear end

Table of Contents

Summary of Contents for Kinroad XT50QT-5

Page 1 ： FOREWORD Thanks for your purchasing this motorcycle. With the help of this manual, you will learn the correct procedures of operation and basic knowledge of maintenance and trouble shooting of the motorcycle. It presents all the basic knowledge of maintenance and trouble shooting of the motorcycle.
Page 2: Table Of Contents
Engine No.: NOTES FOR SAFE RIDING CONTENTS RIDING APPAREL NOTES FOR SAFE RIDING……………………………2 1.Loose，fancy clothing can be uncomfortable and unsafe when riding your motorcycle ． Choose good quality LOCATION OF PARTS…………………………… …4 motorcycle riding apparel when riding your motorcycle． 2. most motorcycle accident fatalities are due to head INSTRUMENT PANEL……………………………...
Page 3 RULES FOR SAFE DRIVE MODIFICATION Check must be conducted before starting the engine any modification of the motorcycle or removal of the to prevent mishaps and damage to components. original equipment may render the vehicle unsafe or Only the qualified person who has passed the drive illegal examination with a drive license is permitted to drive P1ease...
Page 4: Location Of Parts
LOCATION OF PARTS - 4 -...
Page 5 - 5 -...
Page 6 1.Ignition switch/stolen-prevention lock 2.Electric starter switch 3.Lamp switch 4.Handlebar 5.Front brake lever 6.Right mirror 7.Fuel level indicator 8.The turn signals - 6 -...
Page 7 9.speedometer 12.Rear brake lever lO.Left mirror 13.Turn signals switch 11.Switch to change the far and near light l4.Horn button - 7 -...
Page 8: Instrument Panel
INSTRUMENT PANEL HOW TO USE THE INSTRUMENT PANEL MAIN POINTS The indicator will stop at E position when ignition switch turned position. place the motorcycle on the center stand to read the number of the left fuel. ④THE TURN SIGNALS Turn the switch to“LEFT”or“RIGHT”position，the turn signal will flash to advise the driver．...
Page 9: Using Methods Of Switches
USING METHODS OF THE SWITCHES THE IGNITION SWITCH The ignition switch control the start，the wiring diagram for lights and the lock for the handlebars． Please take the key with you when yon leave your motorcycle． (ON)it is connected． 1.You can start the engine． 2.You can drive 3.You can not take the key down (OFF)it is shut down．...
Page 10 MAIN POINTS 1.If it is hard to lock，you can turn the handlebar to the right a little and then lock it. MAIN POINTS 2.Shake the handlebars left and right to be sure Do not use the horn if un- necessary. that it has been locked.
Page 11: Using Methods Of Trunk
off. Light switch The front light switch has three positions, OPEN THE TRUNK And “●”(a white point). Open the seat when you want use the trunk or put When the switch is in this position, the the helmet in it. front head light ,tail and meter lights are 1.put the ignition key in the lock of the seat and...
Page 12: Add Gasoline And Engine Oil
! CAUTION MAIN POINTS for the structure and work principle are difference 1.The trunk load capacity is 10kg． between 2T and 4T engine, do not use the 4-stroke 2.Do not keep heat- Sensitive item in trunk when engine oil with your engine the trunk may get hot．...
Page 13: Correct Driving Operations
adding oil. STARTING METHOD OF THE ENGINE 2.The engine will be easily damaged when driving without oil. BEFORE STARTING 3.Don’t mix oil with other type of oil and it will affect the performance of the engine. 1.You must check the volume of oil and gasoline. 4.Wipe off the oil outside the engine.
Page 14 [2]Hold the front and rear levers MAIN POINTS The electric start will be un-functional if the brake levers are not squeez ed ． Don’t rotate the throttle handlebar when pressing the start button ． - 14 -...
Page 15 MAIN POINTS 1.After the engine is ignited，please release the start button to avoid affecting the engine． 2.To avoid empty the battery ，please use the kick starter to start the engine after 3 seconds by the electric start or and then check the starting system. 3.Please rotate throttle...
Page 16 First confirm the following items then start again. [1]Turn the ignition switch to ON position. [2]Hold the rear brake lever with the left hand and press the front part of the seat with the right hand. [4] Preheat the engine while it is cool. ！CAUTION [3]Kick the kick starter with the right foot.
Page 17 Know well about the correct driving way. It is good not only for security，but also for the [2]THE PROCEDURE TO DRIVE MOTORCYCLE using life of your motorcycle．saving fuel and oil． Hold the handlebars with both hands, sit on the METHOD OF STARTING seat from the left．At this time.
Page 18 NOTE If rotate the handlebar Of throttle too much ，it may make the motorcycle run for-ward suddenly． ADJUST SPEED Adjust speed through rotating handlebar throttle． NOTE Note the cars from the back． [4] START Loosen the brakes and rotate the handlebar of throttle to make the motorcycle start gradually.
Page 19 BE EXTRA SAFETY CONSCIOUS ON BAD WEATHER DAYS Riding on bad weather days ， especially wet ones requires extra Caution ． Braking distance double on a rainy day ． Stay off of the painted surface marks ， manhole covers and greasy appearing areas as they can be especially slippery ．...
Page 20 Return the throttle and squeeze the front and rear brake levers. At the same time, the brake indicator is [3] Place the motor cycle on the center stand lit to inform the following drivers. place the motorcycle on the center stand on the place where does not affect traffic .
Page 21 key with you when you leave. - 21 -...
Page 22 BREAK IN Proper break-in is important to achieve maximum Check the following items before going to service life and performance from your motorcycle． station． 1.The first month or the first 1000 km drive The engine can not be started? with in 45km／h． Check the following items again：...
Page 23 PAY ATTENTION TO S ECURITY WHILE INSPECTING THE ENGINE IS OFF WHILE DRIVING NOTE Please check the following items; 1.Place the motorcycle on the center stand on a 1.Is there fuel? wide and plat place. If there is no fuel in the fuel tank, go to the 2.Avoid hurting from the heat...
Page 24 driving the motorcycle． × × CHECK THE FUNCTION OF THE BRAKES Squeeze the brake levers to see if the play is between the standardized limits． 10∽20mm 10∽20mm more suitalbe less !CAUTION The abnormal tire pressure and tire crack ＆ damages and abnormal wearing are the mail causes to make unfunctional turning and explode the tires．...
Page 25 CHECK LUBRICANT OF THE ENGINE Turn the ignition switch to ON position to see if the oil indicator 1it or not，if it is lit，please add Lubricant oil to the engine. !CAUTlON Don’t make lubricant oil in the engine run off other - wise the engine will be damaged while driving.
Page 26: Periodical Inspections
Check if the front fork is bent or damaged．Check if there is abnormal noises while shaking the handle bars up and down． PERIODICAL INSPECTION If the front fork is abnormal, consult KINROAD service Periodical inspections are done by the riders them station. selves, they are divided into...
Page 27 10-20mm 10-20mm please refer to page 31 to adjust me brake lever play． FUNCTION OF THE BRAKES Tire pressure: front :175KPa Rear :225Kpa Check front rear brakes 。 function If the tires are abnormal，please go to dealers service separately by drive on the dry road with 1ow speed． station or replace them．...
Page 28 CHECK THE LUBRICANT OF THE ENGINE Check the oil pump and the oil tank to see if there is on leakage．If there is oil 1eakage p1ease ask dealer to check and maintain it CHECK THE FLUID VOLUME OF THE BATTERY CHECK THE LEVEL OF OIL OF THE ENGINE This battery need not maintaining.
Page 29: Simple Maintenance Methods
5.Pay attention to the heat of the engine and the exhaust pipe. CHECK THE FUNCTION OF THE LIGHTS ＆ THE TURN SIGNAL INDICATOR FRONT& REAR BRAKE ADJUSTMENT the rear and front brake lever play measured at 1.Check the lights with the head light, turn the end of the levers should be 10-20mm signals and the tail light．...
Page 30 shows ． Press the brake lever to the end ． if the indicator shows that it is out the using limits，please go to the dealer’s service station to replace it． REPLACE THE FUSE Turn the ignition switch to OFF to check if the fuse is complete，replace the fuse if it is blown．...
Page 31 3.If the spare fuse installed blows in a short 2.The battery has been charged and added battery period of time， please try to find other cause，replace liquid，you need not check the level of the liquid or fuse after you have solve these causes. add water 4.Avoid water going into the fuse box when washing 3.Please...
Page 32 3.Immerse the air cleaner element in a pool of PARTS NEED PERIODICALLY REPLACEMENT clean motor oil and squeeze the oil off the air With driving your motorcycles， sometimes you cleaner element to make it slightly wet with the oil． can not judge some parts which can be used 1onger...
Page 33: Specifications
SPECIFICATIONS Item Item 50CC 50CC 41×37.4 Overall length 1650mm Cylinder bore × stroke 9.2:1 Overall width 625mm Compression ratio 1.37kw/6000r/min Overall height 1050mm Output(max) 2.36N.m/4500r/min Wheelbase 1210mm Torque(max) 1500r±100r/min Dead weight 72kg Idling speed Payload 150kg Displacement of cylinder 49.2 ml 3.00-10 Spark plug Front wheel...
Page 34: Electrical Diagram
Transmission ratio 6.182 Maximum transmission ratio 2.143 Minimum transmission ratio Final reduction 13.247 ELECTRICAL DIAGRAM - 34 -...

Kinroad XT50QT-5 User Manual

Table of Contents

Related Manuals for Kinroad XT50QT-5

Summary of Contents for Kinroad XT50QT-5

Table of Contents