Table of Contents
Advertisement
：
FOREWORD
Thanks for your purchasing this motorcycle.
With the help of this manual, you will learn the
correct procedures of operation and basic knowledge of
maintenance and trouble shooting of the motorcycle. It
presents all the basic knowledge of maintenance and
trouble shooting of the motorcycle. It presents all
the details of the performance of this motorcycle to
you and the vehicle will make your life more relaxed
and happier.
In case any picture does not agree with the vehicle
physically, the latter shall prevail.
CAUTION． NOTE and MAIN POINTS
ings and should be carefully reviewed．
!CAUTION
：The personal safety of the rider may be
involved，disregarding this information could result in
injury to the rider．
NOTE
： These instructions point out special service
procedures or precautions that must be followed to
avoid damaging the machine．
MAIN POINTS
： This provides special information to make
maintenance easier or important instructions clearer．
VIN AND ENGINE SERIAL NUMBER LOCATION
register the motorcycle ． They are also use to assist
carry special mean-
your dealer when ordering parts or special service
information.
The VIN is stamped on the front main beam of the
frame．
The engine serial number is stamped on the rear end
of the crankcase assembly
VIN. :
- 1 -
The VIN and/or engine serial number are used to
Advertisement
Table of Contents
Related Manuals for Kinroad XT125T-17
Summary of Contents for Kinroad XT125T-17
- Page 1 ： FOREWORD VIN AND ENGINE SERIAL NUMBER LOCATION Thanks for your purchasing this motorcycle. The VIN and/or engine serial number are used to With the help of this manual, you will learn the register the motorcycle ． They are also use to assist correct procedures of operation and basic knowledge of maintenance and trouble shooting of the motorcycle.
-
Page 2: Table Of Contents
Engine No.: ELECTRICAL DIAGRAM……………………… ……31 CONTENTS NOTES FOR SAFE RIDING……………………………2 NOTES FOR SAFE RIDING LOCATION OF PARTS…………………………… …4 RIDING APPAREL INSTRUMENT PANEL…………………………… ……7 1.Loose，fancy clothing can be uncomfortable and unsafe when riding your motorcycle ． Choose good quality USING METHODS OF SWITCHES……… ……………8 motorcycle riding apparel when riding your motorcycle．... - Page 3 be conducted before starting the engine to prevent MODIFICATION mishaps and damage to components. Only the qualified person who has passed the drive any modification of the motorcycle or removal of the examination with a drive license is permitted to drive original equipment may render the vehicle unsafe or the vehicle but not anybody else without a drive license.
-
Page 4: Location Of Parts
LOCATION OF PARTS - 4 -... - Page 5 - 5 -...
- Page 6 1.Ignition switch/stolen-prevention lock 2.Electric starter switch 3.Lamp switch 4.Handlebar 5.Front brake lever 6.Right mirror 7.Voltage indicator 8.The turn signals 9. speedometer lO.Fuel level indicator 11.Left mirror 12.Switch to change the far and near light 13.Rear brake lever l4.Turn signals switch 15.Horn button - 6 -...
-
Page 7: Instrument Panel
INSTRUMENT PANEL The‘‘E’’mark indicates the fuel tank is empty or HOW TO USE THE INSTRUMENT PANEL nearly so． MAIN POINTS The indicator will stop at E position when ignition switch turned position. place the motorcycle on the center stand to read the number of the left fuel. - Page 8 USING METHODS OF THE SWITCHES THE IGNITION SWITCH The ignition switch control the start，the wiring diagram for lights and the lock for the handlebars． Please take the key with you when yon leave your motorcycle． (ON)it is connected． 1.You can start the engine． 2.You can drive 3.You can not take the key down (OFF)it is shut down．...
- Page 9 MIDDLE：the turn signal will not flash． MAIN POINTS After you have finished， please turn off the turn 1.If it is hard to lock，you can turn the handlebar signals． to the right a little and then lock it. 2.Shake the handlebars left and right to be sure THE HORN BUTTON that it has been locked.
- Page 10 betraying and meter Lights are lit up. NOTE “ ● ”When this position. front If the engine call not be started in 3 seconds, illuminator, tail, betraying and meter lights are all please use the kick starter to stare the engine to off.
-
Page 11: Add Gasoline And Engine Oil
see if the lock is closed. much attention to this. 2.If you press the seat when the ignition key in 3.Do not keep such items as cotton on any place the trunk, you can not take the key out, so please pay under the seat except the trunk. - Page 12 CHANGE ENGINE OIL Change engine after first 300km riding．Afterwards，change it every 1000km，check the volume every 500km riding and add it to the standard volume in time．The full volume is 0.9L and the replace volume is 0.75L． CHANGE GEAR OIL Change the gear oil after the first 300km and every 5000km successively or every half a year, whichever comes first.
-
Page 13: Correct Driving Operations
NOTE 1. Don’t fill oil prior to the FULL level when adding oil. CORRECT DRIVING OPERATIONS 2.The engine will be easily damaged when driving without oil. STARTING METHOD OF THE ENGINE 3.Don’t mix oil with other type of oil and it BEFORE STARTING will affect the performance of the engine. - Page 14 MAIN POINTS [2]Hold the front and rear levers The electric start will be un-functional if the brake levers are not squeez ed ． Don’t rotate the throttle handlebar when pressing the start button ． - 14 -...
- Page 15 MAIN POINTS 1.After the engine is ignited，please release the start button to avoid affecting the engine． 2.To avoid empty the battery ，please use the kick starter to start the engine after 3 seconds by the electric start or and then check the starting system. 3.Please rotate throttle...
- Page 16 First confirm the following items then start again. [1]Turn the ignition switch to ON position. [2]Hold the rear brake lever with the left hand and press the front part of the seat with the right hand. [4] Preheat the engine while it is cool. ！CAUTION [3]Kick the kick starter with the right foot.
- Page 17 Know well about the correct driving way. It is good not only for security，but also for the [2]THE PROCEDURE TO DRIVE MOTORCYCLE using life of your motorcycle．saving fuel and oil． Hold the handlebars with both hands, sit on the METHOD OF STARTING seat from the left．At this time.
- Page 18 NOTE If rotate the handlebar Of throttle too much ，it may make the motorcycle run for-ward suddenly． ADJUST SPEED Adjust speed through rotating handlebar throttle． NOTE Note the cars from the back． [4] START Loosen the brakes and rotate the handlebar of throttle to make the motorcycle start gradually.
- Page 19 Rear brake Front brake BE EXTRA SAFETY CONSCIOUS ON BAD WEATHER DAYS Riding on bad weather days ， especially wet ones requires extra Caution ． Braking distance double on a rainy day ． Stay off of the painted surface marks ， manhole covers and greasy appearing areas as they can be especially slippery ．...
- Page 20 Return the throttle and squeeze the front and rear brake levers. At the same time, the brake indicator is [3] Place the motor cycle on the center stand lit to inform the following drivers. place the motorcycle on the center stand on the place where does not affect traffic .
- Page 21 key with you when you leave. - 21 -...
- Page 22 BREAK IN Proper break-in is important to achieve maximum Check the following items before going to service life and performance from your motorcycle． station． 1.The first month or the first 1000 km drive The engine can not be started? with in 45km／h． Check the following items again：...
- Page 23 PAY ATTENTION TO S ECURITY WHILE INSPECTING THE ENGINE IS OFF WHILE DRIVING NOTE Please check the following items; 1.Place the motorcycle on the center stand on a 1.Is there fuel? wide and plat place. If there is no fuel in the fuel tank, go to the 2.Avoid hurting from the heat...
- Page 24 driving the motorcycle． × × CHECK THE FUNCTION OF THE BRAKES Squeeze the brake levers to see if the play is between the standardized limits． 10∽20mm 10∽20mm more suitalbe less !CAUTION The abnormal tire pressure and tire crack ＆ damages and abnormal wearing are the mail causes to make unfunctional turning and explode the tires．...
- Page 25 CHECK LUBRICANT OF THE ENGINE Turn the ignition switch to ON position to see if the oil indicator 1it or not，if it is lit，please add Lubricant oil to the engine. !CAUTlON Don’t make lubricant oil in the engine run off other - wise the engine will be damaged while driving.
-
Page 26: Periodical Inspections
Check if the front fork is bent or damaged．Check if there is abnormal noises while shaking the handle bars up and down． PERIODICAL INSPECTION If the front fork is abnormal, consult KINROAD service Periodical inspections are done by the riders them station. selves, they are divided into... - Page 27 10-20mm 10-20mm please refer to page 31 to adjust me brake lever play． FUNCTION OF THE BRAKES Tire pressure: front :175KPa Rear :225Kpa Check front rear brakes 。 function If the tires are abnormal，please go to dealers service separately by drive on the dry road with 1ow speed． station or replace them．...
- Page 28 CHECK THE TRANSMISSION LEAKAGE and the oil line is abnormal，go to the dealers service Check the transmission to see if there is oil station to check． leakage If the transmission leaks oil please go to KINROAD service station． - 28 -...
- Page 29 5.Pay attention to the heat of the engine and the exhaust pipe. CHECK THE FUNCTION OF THE LIGHTS ＆ THE TURN SIGNAL INDICATOR FRONT& REAR BRAKE ADJUSTMENT the rear and front brake lever play measured at 1.Check the lights with the head light, turn the end of the levers should be 10-20mm signals and the tail light．...
- Page 30 REPLACE THE FUSE Turn the ignition switch to OFF to check if the fuse is complete，replace the fuse if it is blown． The fuse is on the terminal of the battery ， the standard current flow is 15 A. !CAUTION Make the pin in the concave part of the adjuster INSTALL AND ASSEMBLE THE FUSE otherwise, the clearance between the rear brake 1ever...
- Page 31 4.Charge the battery every 6 months when it is used for a 1ong time． CLEAN THE TERMINAL OF BATTERY 5.If you use other charger except for the c1osed 1.Wash the terminal with warm water when there are battery ， obey following rules prevent...
- Page 32 example： 1.brake line：every 2 years 2.fuel hoses：every 4 years 3.oil for transmission case：every 1000 km When you replace parts，please buy them from motorcycle dealers. !CAUTION 1.Gasoline ignition-point solvent easily flammable, so please not use them when washing the air cleaner element. 2.Uncomplete assemblage will affect driving so make sure to assemble the air cleaner clement fixed.
-
Page 33: Specifications
SPECIFICATIONS 150CC 125CC 150CC 125CC 52.4×57.8 57.4×57.8 Overall length 2200mm 2200mm Cylinder bore × stroke 9.2:1 9.8:1 Overall width 750mm 750mm Compression ratio 6.8kw/7500r/min Overall height 1405mm 1405mm Output(max) 4.1kw/7000r/min 6.5N.m/5500r/min 8.5N.m/7000r/min Wheelbase 1490mm 1490mm Torque(max) 1500r±100r/min 1500r±100r/min Dead weight 141kg 141kg Idling speed... -
Page 34: Electrical Diagram
22.76 Maximum transmission ratio Minimum transmission ratio 7.41 Final reduction ELECTRICAL DIAGRAM - 34 -...