Advertisement
Table of Contents
- 1 Table of Contents
- 2 Notes for Safe Riding
- 3 Location of Parts
- 4 Instrument Panel
- 5 Using Methods of Switches
- 6 Light Switch
- 7 Using Methods of Trunk
- 8 Add Gasoline and Engine Oil
- 9 Correct Driving Operations
- 10 Periodical Inspections
- 11 Simple Maintenance Methods
- 12 Specifications
- 13 Electrical Diagram
- Download this manual
：
FOREWORD
Thanks for your purchasing this motorcycle.
With the help of this manual, you will learn the
correct procedures of operation and basic knowledge of
maintenance and trouble shooting of the motorcycle. It
presents all the basic knowledge of maintenance and
trouble shooting of the motorcycle. It presents all
the details of the performance of this motorcycle to
you and the vehicle will make your life more relaxed
and happier.
In case any picture does not agree with the vehicle
physically, the latter shall prevail.
CAUTION． NOTE and MAIN POINTS
ings and should be carefully reviewed．
!CAUTION
：The personal safety of the rider may be
involved，disregarding this information could result in
injury to the rider．
NOTE
： These instructions point out special service
procedures or precautions that must be followed to
avoid damaging the machine．
MAIN POINTS
： This provides special information to make
maintenance easier or important instructions clearer．
VIN AND ENGINE SERIAL NUMBER LOCATION
register the motorcycle ． They are also use to assist
carry special mean-
your dealer when ordering parts or special service
information.
The VIN is stamped on the front main beam of the
frame．
of the crankcase assembly
- 1 -
The VIN and/or engine serial number are used to
The engine serial number is stamped on the rear end
Advertisement
Table of Contents
Related Manuals for Kinroad XT125T-10
Summary of Contents for Kinroad XT125T-10
- Page 1 ： FOREWORD VIN AND ENGINE SERIAL NUMBER LOCATION Thanks for your purchasing this motorcycle. The VIN and/or engine serial number are used to With the help of this manual, you will learn the register the motorcycle ． They are also use to assist correct procedures of operation and basic knowledge of maintenance and trouble shooting of the motorcycle.
-
Page 2: Table Of Contents
VIN. : Engine No.: NOTES FOR SAFE RIDING CONTENTS RIDING APPAREL NOTES FOR SAFE RIDING……………………………2 1.Loose，fancy clothing can be uncomfortable and unsafe when riding your motorcycle ． Choose good quality LOCATION OF PARTS…………………………… …4 motorcycle riding apparel when riding your motorcycle． 2. - Page 3 RULES FOR SAFE DRIVE Check must be conducted before starting the engine to prevent mishaps and damage to components. MODIFICATION Only the qualified person who has passed the drive examination with a drive license is permitted to drive any modification of the motorcycle or removal of the the vehicle but not anybody else without a drive license.
-
Page 4: Location Of Parts
condition, its stability, security and speed will be affected. LOCATION OF PARTS - 4 -... - Page 5 - 5 -...
- Page 6 1.Ignition switch/stolen-prevention lock 2.Electric starter switch 3.Lamp switch 4.Handlebar 5.Front brake lever 6.Right mirror 7.Fuel level indicator 8.The turn signals 9.speedometer lO.Left mirror 11.Switch to change the far and near light 12.Rear brake lever 13.Turn signals switch l4.Horn button - 6 -...
-
Page 7: Instrument Panel
INSTRUMENT PANEL The‘‘E’’mark indicates the fuel tank is empty or HOW TO USE THE INSTRUMENT PANEL nearly so． MAIN POINTS The indicator will stop at E position when ignition switch turned position. place the motorcycle on the center stand to read the number of the left fuel. -
Page 8: Using Methods Of Switches
USING METHODS OF THE SWITCHES THE IGNITION SWITCH The ignition switch control the start，the wiring diagram for lights and the lock for the handlebars． Please take the key with you when yon leave your motorcycle． (ON)it is connected． 1.You can start the engine． 2.You can drive 3.You can not take the key down (OFF)it is shut down．... -
Page 9: Light Switch
MAIN POINTS THE CHANGEABLE SWITCH FOR 1.If it is hard to lock，you can turn the handlebar to the right a little and then lock it. THE FRONT LIGHT 2.Shake the handlebars left and right to be sure Use this switch ， you can that it has been locked. -
Page 10: Using Methods Of Trunk
When the switch is in this position, the front Open the seat when you want use the trunk or put head light ,tail and meter lights are all lit up. the helmet in it. When switch this position,the tail, 1.put the ignition key in the lock of the seat and betraying and meter Lights are lit up. -
Page 11: Add Gasoline And Engine Oil
ignition key in the trunk, you can not take the key 3.Do not keep such items as cotton on any place out, so please pay much attention to this. under the seat except the trunk. ADD GASOLINE AND ENGINE OIL ADD GASOLINE There is a gasoline tank gate at the rear part of the seat，open it with the ignition key , take down the... - Page 12 CHANGE ENGINE OIL Change engine after first 300km riding．Afterwards，change it every 1000km，check the volume every 500km riding and add it to the standard volume in time．The full volume is 0.9L and the replace volume is 0.75L． CHANGE GEAR OIL Change the gear oil after the first 300km and every 5000km successively or every half a year, whichever comes first.
-
Page 13: Correct Driving Operations
NOTE 1. Don’t fill oil prior to the FULL level when adding oil. CORRECT DRIVING OPERATIONS 2.The engine will be easily damaged when driving without oil. STARTING METHOD OF THE ENGINE 3.Don’t mix oil with other type of oil and it BEFORE STARTING will affect the performance of the engine. - Page 14 MAIN POINTS The electric start will be un-functional if the brake levers are not squeez ed ． Don’t rotate the throttle handlebar when pressing the start button ． [2]Hold the front and rear levers MAIN POINTS 1.After the engine is ignited，please release the start button to avoid affecting the engine．...
- Page 15 First confirm the following items then start again. [1]Turn the ignition switch to ON position. [2]Hold the rear brake lever with the left hand and press the front part of the seat with the right hand. [4] Preheat the engine while it is cool. ！CAUTION [3]Kick the kick starter with the right foot.
- Page 16 Know well about the correct driving way. It is good not only for security，but also for the [2]THE PROCEDURE TO DRIVE MOTORCYCLE using life of your motorcycle．saving fuel and oil． Hold the handlebars with both hands, sit on the METHOD OF STARTING seat from the left．At this time.
- Page 17 NOTE If rotate the handlebar Of throttle too much ，it may make the motorcycle run for-ward suddenly． ADJUST SPEED Adjust speed through rotating handlebar throttle． NOTE Note the cars from the back． [4] START Loosen the brakes and rotate the handlebar of throttle to make the motorcycle start gradually.
- Page 18 BE EXTRA SAFETY CONSCIOUS ON BAD WEATHER DAYS Riding on bad weather days ， especially wet ones requires extra Caution ． Braking distance double on a rainy day ． Stay off of the painted surface marks ， manhole covers and greasy appearing areas as they can be especially slippery ．...
- Page 19 then drive to the sides of the road． - 19 -...
- Page 20 Return the throttle and squeeze the front and rear brake levers. At the same time, the brake indicator is [3] Place the motor cycle on the center stand lit to inform the following drivers. place the motorcycle on the center stand on the place where does not affect traffic .
- Page 21 key with you when you leave. - 21 -...
- Page 22 BREAK IN Proper break-in is important to achieve maximum Check the following items before going to service life and performance from your motorcycle． station． 1.The first month or the first 1000 km drive The engine can not be started? with in 45km／h． Check the following items again：...
- Page 23 PAY ATTENTION TO S ECURITY WHILE INSPECTING THE ENGINE IS OFF WHILE DRIVING NOTE Please check the following items; 1.Place the motorcycle on the center stand on a 1.Is there fuel? wide and plat place. If there is no fuel in the fuel tank, go to the 2.Avoid hurting from the heat...
- Page 24 driving the motorcycle． × × CHECK THE FUNCTION OF THE BRAKES Squeeze the brake levers to see if the play is between the standardized limits． 10∽20mm 10∽20mm more suitalbe less !CAUTION The abnormal tire pressure and tire crack ＆ damages and abnormal wearing are the mail causes to make unfunctional turning and explode the tires．...
- Page 25 CHECK LUBRICANT OF THE ENGINE Turn the ignition switch to ON position to see if the oil indicator 1it or not，if it is lit，please add Lubricant oil to the engine. !CAUTlON Don’t make lubricant oil in the engine run off other - wise the engine will be damaged while driving.
-
Page 26: Periodical Inspections
PERIODICAL INSPECTION Periodical inspections are done by the riders them selves, they are divided into 6 monthly and l2 monthly inspections． There are two sections：A section and B section in 6-monthly inspections． A section ： I f you have basic knowledge of motorcycles，you can do the inspections by yourselves．... - Page 27 1ow speed． If the front fork is abnormal, consult KINROAD service station. If the function of the brakes is not good, please refer to page 31 about brake shoe corrosion.
- Page 28 ， it will affect the engine by dirt going into． 2.No water should go into it when washing the motorcycle. If the transmission leaks oil please go to KINROAD service station． CHECK THE LUBRICANT OF THE ENGINE Check the oil pump and the oil tank to see if there is on leakage．If there is oil 1eakage p1ease ask...
-
Page 29: Simple Maintenance Methods
SIMPLE MAINTANCE METHODS After the above inspections, you should do some other simple adjustments replacements．This manual will give some common and useful maintenance methods． !CAUTION Pay attention to safety when you maintain your motorcycle． 1.select a safe place which is flat，Wide and no dangers around. - Page 30 !CAUTION` Replace the brake shoe if the marked continuous line is out of the limits when you take the brake lever tightly. CORROSION OF THE BRAKE SHOE know corrosion status brake shoe ． please inspect the places as the picture shows ．...
- Page 31 fuse from the terminal. MAIN POINTS Don’t touch the central part of the terminal after you take it down from the battery． !CAUTION 1.Always be sure to replace the blown fuse with the correct amperage fuse． !CAUTION 2.Using super amperage fuse will lead to heat or This motorcycle uses 12V—closed battery which damage of the lines．...
- Page 32 PAY ATTENTION TO USING THE BATTERY The battery can have flammable gas，if it is not used correctly，injures and damages will happen． 1.Fire is forbidden ， short circuit should be prevented, and smoke and other fire should be far form !CAUTION it．...
-
Page 33: Specifications
SPECIFICATIONS 150CC 125CC 150CC 125CC 52.4×57.8 57.4×57.8 Overall length 1890mm 1890mm Cylinder bore × stroke 9.2:1 9.8:1 Overall width 750mm 750mm Compression ratio 6.8kw/7500r/min Overall height 1035mm 1035mm Output(max) 4.0kw/5500r/min 6.8N.m/5500r/min 8.5N.m/7000r/min Wheelbase 1310mm 1310mm Torque(max) 1500r±100r/min 1500r±100r/min Dead weight 104kg 104kg Idling speed... -
Page 34: Electrical Diagram
D8TC D8TC 90/90-12 120/70-12 Spark plug Front wheel 0.6-0.8mm 0.6~0.8mm Rear wheel 3.50-10 120/70-12 Spark plug gap Inlakevalve:0.05mm Inlakevalve:0.05mm Speed(max) 75km/h 85km/h Gap of air valve Exhaust Exhaust Braking distance ≤7m(30km/h) ≤7m(30km/h) valve:0.08mm valve:0.08mm 150mm 150mm Climb ability ≥18° ≥18° Ground clearance Capacity of gasoline Ignition means...