Care And Maintenance - Hilti PM 2-L Operating Instructions Manual

8. Mark the mid points of d1 and d2.
If the reference points 1 and 3 are located on dif-
ferent sides of the mid point, then subtract d2 from
d1.
If the reference points 1 and 3 are located on the
same side of the mid point, then add d1 and d2
together.
9. Divide the result by twice the length of the room
(room length x 2).
The maximum permissible error is 3 mm.
7.3.2 Checking the accuracy of the horizontal
line 9 10
1. Place the tool at the edge of a room with a length of
at least 10 m.
NOTE The floor surface must be even and level.
2. Switch on all laser beams.
3. Set up a target plate at a distance of at least 10 m
from the tool, so that the point of intersection of the
laser lines lies in the center of the target plate (d0)
and the vertical line on the target plate runs exactly
through the middle of the vertical laser line.
4. Pivot the tool clockwise through 45° (as seen from
above).
5. Then mark the point (d1) on the target plate where
the horizontal laser line strikes the vertical line on
the target plate.
6. Pivot the tool counterclockwise through 90°. The
reference point must remain on the center of the
reference cross.
7. Then mark the point (d2) on the target plate where
the horizontal laser line strikes the vertical line on
the target plate.

8 Care and maintenance

8.1 Cleaning and drying
1. Blow dust off the glass.
2. Do not touch the glass with the fingers.
3. Use only a clean, soft cloth for cleaning. If necessary,
moisten the cloth slightly with pure alcohol or a little
water.
NOTE Do not use any other liquids as these may
damage the plastic components.
4. Observe the temperature limits when storing your
equipment. This is particularly important in winter
/ summer if the equipment is kept inside a motor
vehicle (-25°C to +60°C).
8.2 Storage
Remove the tool from its case if it has become wet.
The tool, its carrying case and accessories should be
cleaned and dried (at maximum 63°C / 145°F). Repack
the equipment only once it has dried completely and then
store it in a dry place.
Check the accuracy of the equipment before it is used
after a long period of storage or transportation.
Remove the batteries from the tool before storing it for a
long period. Leaking batteries may damage the tool.
8. Measure the following vertical distances: d0-d1, d0-
d2 and d1-d2.
NOTE The greatest measured vertical distance must
be no more than 5 mm at a working distance of 10
m.
7.3.3 Checking the vertical lines 11
1. Position the tool at a height of 2 meters.
2. Switch the tool on.
3. Position the first target plate T1 (vertical) at a dis-
tance of 2.5 meters from the tool at the same height
(2 meters), so that the vertical laser beam strikes the
plate. Mark this position.
4. Then place the second target plate T2 at a position 2
meters below the first target plate, so that the vertical
laser beam strikes the plate. Mark this position.
5. Mark position 2 at the opposite side of the test
setup (mirror image) on the laser line on the floor at
a distance of 5 meters from the tool.
6. Now place the tool on the floor on the mark for
position 2 which you have just made. Direct the
laser beam toward the target plates T1 and T2 so
that it strikes the plates close to their center lines.
7. Read the distances D1 and D2 from each target
plate (distance of the laser line from the center of
the target plate) and calculate the difference (D = D1
- D2).
NOTE Take care to ensure that the target plates are
parallel to each other and that they are in the same
vertical plane. (Horizontal alignment may result in
measurement error).
If the difference D is greater than 3 mm, the tool must
be returned to a Hilti repair center for readjustment.
8.3 Transport
Use the Hilti toolbox or packaging of equivalent quality
for transporting or shipping your equipment.
CAUTION
Always remove the batteries before shipping the tool.
8.4 Hilti calibration service
We recommend that the tool is checked by the Hilti cal-
ibration service at regular intervals in order to verify its
reliability in accordance with standards and legal require-
ments.
Use can be made of the Hilti calibration service at any
time, but checking at least once a year is recommended.
The calibration service provides confirmation that the
tool is in conformance, on the day it is tested, with the
specifications given in the operating instructions.
The tool will be readjusted if deviations from the man-
ufacturer's specification are found. After checking and
adjustment, a calibration sticker applied to the tool and
a calibration certificate provide written verification that
the tool operates in accordance with the manufacturer's
specification.
en
17