Replacing The Battery; Assembly Instructions - Peg-Perego Polaris RANGER RZR IGOD0516 Use And Care Manual

Hide thumbs

Table Of Contents

Table of Contents

Available languages

Enlarged version

ASSEMBLY INSTRUCTIONS

WARNING

ASSEMBLY MUST ONLY BE CARRIED OUT BY

ADULTS. TAKE CARE WHEN REMOVING THE

VEHICLE FROM ITS PACKAGING. ALL THE

SCREWS AND SMALL PARTS ARE CONTAINED IN

A BAG INSIDE THE PACKAGING. THE BATTERY

MAY ALREADY BE FITTED INSIDE THE ITEM.

ASSEMBLY

1 • Remove the 4 fixing screws from the two seat

base sections.

2 • Pull out and remove the two seat bases.

3 • Remove the fixing screws from the two rear

base fixtures.

4 • Remove the two rear base locks.

5 • Pull the base in the direction of the arrow to

fully remove the motor unit.

6 • Reposition and screw on both rear base locks.

7 • Lift the two shock absorbers (1). Insert them

into the holes in the bodywork (2).

8 • Attach the shock absorbers to the bodywork

with the two pins (one each side). Note: the

packaging contains two spare pins.

9 • Insert the exhaust pipe as shown in the figure.

10 • Attach the exhaust pipe with the screw

provided.

11 • Position the rear box.

12 • Insert the tabs on the front of the rear box into

the bodywork (two each side).

13 • Fully insert the two metal tubes (one each side)

as shown in the figure.

14 • Attach the rear box with the three screws

provided. Important: the middle screw must be

tightened as shown in the following figure.

15 • Press the pin to help align the screw holes.

16 • Before fitting the side supports, check the picture

to make sure they match the grilles properly.

17 • Hook the lower ring of the support onto the

grille, as shown in the figure.

18 • Complete the attachment process by fitting the

upper ring. Make sure the front part of the grille

is inserted properly.

19 • Picture A shows the front part of the grille when

it is not yet fitted correctly. Picture B shows the

grille fitted correctly.

20 • Insert the side guards as shown in the figure,

taking care to fit the parts with the grid

extending towards the outside. Complete the

attachment by pushing the guards forward until

they click into position.

21 • Pull out the side panels of the bodywork (1) and

insert the side guard clips (2).

22 • Line up the inserts in the two side panels with

the matching holes in the bodywork, as shown in

the figure.

23 • Press the side panels of the bodywork at the two

points shown in the figure to fix them in place.

24 • Secure the upper profiles of the cargo box with

the screws provided.

25 • Complete the attachment of the rear box by

fastening the two screws inside the cabin.

26 • Rear cover plate:

• A - Housing for attachment to bodywork.

• B - Housing for the insertion of metal tubes.

• C - Housing for the insertion of the exhaust

pipe.

• D - Tabs for fixture to bodywork.

27 • Position the rear cover plate, matching the

various points marked with the letters A, B and

28 • Lift the upper part of the rear cover plate to

facilitate the engagement of the tabs (D).

29 • Secure the rear cover plate with the two screws

as shown in the figure.

30 • Complete the attachment of the rear cover plate

by fastening the screw under the exhaust pipe.

31 • Install with pressure the vertical tube of the roll

bar showing in the drowing. Note: the pieces are

mirrored, as shown in the figure is the left.

32 • Rotate the vertical tube to facilitate the inclusion

of the side bars.

33 • Secure both vertical tubes using standard screw

provided.

34 • Secure the side bars to the vertical tubes with

screw.

35 • Place the back tubes. Note: The pieces are

mirrored.

36 • Fix the rear tubes at the top.

37 • Secure the rear tubes in the lower.

38 • Put the band of the central clamps on the rear

tubes (see proper orientation in the next

picture)

39 • The band should be horizontal and not towards

the top.

40 • Insert the central clamps into bands.

41 • Insert a screw and nut in the holes of the band.

42 • Secure the central clamps.

43 • Place the top of the rollbar. Mantain the holes

represented by the letter A on the front and the

holes represented by the letter B to the rear of

the vehicle.

44 • Secure seat belt and the top of the rollbar to

each vertical tube using screw provided in

separate bag.

45 • Attach the three plastic rings to rollbar. The

holes position is up and down the back of the

vehicle.

46 • Mount the three fog lights on the roof bars and

attach them with the screws provided (one per

light).

47 • Front cover plate:

• A - Tabs for fixing to the bodywork.

• B - Housing for engagement with the bodywork.

• C - Housing for attachment to the base

• D - Tab for engagement to the hood.

• E - Hole for inserting the front roll bar.

48 • Position the front cover plate by inserting the

points indicated with the letters A and B into the

bodywork. Put a hand inside the bodywork at

point B and squeeze it together with the mask to

click it into place (as shown in the circle).

49 • Press on the central area of the front cover plate

at the tab D to attach it to the hood.

50 • Press the lower part of the cover plate to engage

the two tabs C.

51 • Position the front roll bar, sliding it onto the

relevant pins.

52 • Take care with the bottom of the roll bar, which

must be inserted into the hole E of the cover

plate as shown in the picture.

53 • Attach the roll bar with the screw provided.

54 • Complete the attachment of the roll bar with

the two screws at the front.

55 • Press together the two sections of the steering

wheel to fully engage them.

56 • Insert the central steering wheel cap.

57 • Remove the plastic protectors from the steering

shaft.

58 • Position the steering wheel, aligning the holes

with those on the steering shaft.

59 • Attach the steering wheel with the threaded pin

and the bolt (the bolt must be inserted into the

hexagonal hole, the threaded pin in the circular

hole), holding the bolt to keep it in place.

60 • Insert the passenger's handle into the hole on

the dashboard.

61 • Attach the handle with the screws provided.

62 • Snap fit the petrol cap.

63 • Insert the seat base (removed previously) on the

driver's side.

64 • Insert the battery (charged previously) into the

compartment under the seat on the passenger's

side.

65 • Thread the battery plug and the electrical system

plug through the holes in the passenger's seat

base.

66 • Insert the seat base on the passenger side.

67 • Connect the battery and electrical system plugs.

68 • Fasten down the seat bases using 4 screws (two

on each side).

69 • Insert the two short sections of the safety belts

into the seat bases (in the holes near the gear

lever), taking care to insert all of the section of

belt highlighted in detail A. Note: the safety belt

buckle buttons must be facing the gear lever, as

shown in the figure.

70 • Unscrew the knobs from the seat base.

71 • Position the seat. Note: the seat can be adjusted

in length to two different positions, depending on

the height of the child.

72 • Screw the knobs back into position.

73 • Lower the seat.

74 • Tighten the safety screw. Repeat for the other

seat.

75 • Install the two parts of the windshield as shown.

Picture A shows the grille fitted correctly

76 • Secure the grille with the three screws.

77 • Place the windshield on the hood hooking the

three central tabs.

78 • Fit the windscreen of the vehicle with screws

79 • Remove the protectors from the rear axle.

80 • Insert the axle into the rear of the vehicle, as

shown in the figure.

81 • Position the driver in the inside of one of the

two larger wheels.

82 • Slide the wheel onto the axle with the driver

towards the vehicle.

83 • Slide a washer onto the axle.

84 • Fasten the wheel, tightening one of the four nuts

supplied with the spanner provided.

• Repeat the fitting operations for the other rear

wheel. Important: carry out the operations while

holding the axle still on the opposite side with

the help of the second spanner provided.

85 • Remove the protectors from the front axles.

86 • Slide a washer onto the axle.

87 • Slide one of the remaining wheels (narrower

than the rear wheels) onto the axle.

88 • Slide a washer onto the axle.

89 • Fasten the wheel, tightening one of the two

remaining bolts with the spanner provided.

• Repeat the fitting operations for the front wheel

on the other side.

90 • Snap fit the four hub covers onto the wheels.

FEATURES AND USE OF THE VEHICLE

91 • RADIO - Remove the two screws as shown in

the figure to extract the radio and insert the

batteries.

92 • Use a tool to lever the upper part of the radio

front panel and extract it.

93 • Release the screw on the battery compartment

cover.

94 • Insert two AA 1.5V batteries with the polarities

as indicated. Close the battery compartment

cover. Important: always tighten the screw.

95 • Insert the antenna and the radio into the housing

on the dashboard.

96 • Radio functions:

• A - Socket for an MP3 reader jack.

IMPORTANT!: Connect the MP3 reader (not

included) to the vehicle radio using a cable NO

longer than 150 cm.

• B - Radio station selector.

• C - On/Off buttons.

• D - Radio On indicator light.

• E - Volume control knob.

• F - Digital clock adjustment buttons.

97 • Driving cab features:

• A - Steering wheel.

• B - Fully functional radio (see fig 96).

• C - Passenger handle.

• D - Accelerator/electrical brake pedal (see fig

98-99-100).

• E - Gear lever (see fig 101).

• F - Drinks holder (see fig 102).

• G - MP3 player storage compartment.

98 • ACCELERATOR/ELECTRICAL BRAKE PEDAL

SmartPedal Technology™ - When the

accelerator pedal is pressed, the vehicle starts

moving. When the pedal is released, the electrical

brake is activated, automatically stopping the

vehicle.

99 • The second gear lock is located on the pedal.

When the vehicle is removed from its packaging,

the second gear lock is positioned as shown in

figure A (LOW), limiting the vehicle to the lower

speed. When the second gear lock is positioned

as shown in figure B (HIGH), the vehicle can

travel at the faster speed.

100 • To adjust the second gear lock to position B

(HIGH), release the second gear lock fixing

screw and move the unit upwards. Important:

always replace the fixing screw.

101 • GEAR LEVER - When the gear lever is in the

vertical position, the vehicle travels forward at

LOW or HIGH speed. When the gear lever is

pulled back and the accelerator pedal is

pressed at the same time, the vehicle travels in

reverse.

102 • DRINKS HOLDER - There are two drinks

holders for cans or bottles.

103 • REAR BOX and SUSPENSION - The rear of

the vehicle has a spacious cargo box and real

functional suspension on the wheels.

104 • WHEELS with RUBBER STRIPS Red Line

Nitrile Traction™ - The wheels are fitted with

a rubber strip for better grip on all surfaces,

silent performance and greater driving comfort.

105 • SAFETY BELT - To fasten the safety belt, insert

the end of the longer belt section into the

buckle on the shorter belt section, pushing the

two parts together.

106 • To release the safety belt, press the buckle

button and at the same time separate the two

elements.

107 • To change the length of the safety belt, move

the adjuster as shown in the figure.