Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Heatrae Sadia SUPREME
Summary of Contents for Heatrae Sadia SUPREME
- Page 1 SUPREME COUNTER TOP Fitting Instructions and User Guide...
-
Page 2: Component Checklist
INTRODUCTION Thank you for purchasing a Heatrae Sadia Supreme. The boiling water heater is manufactured to the highest standards and has been designed to meet all the latest relevant safety specifications. This Heatrae Sadia water heater must be installed (Sections 1-6), commissioned (Section 7) and maintained (Sections 8-11) by a competent person. -
Page 3: Technical Specifications
TECHNICAL SPECIFICATIONS Electrical rating 2.8 - 3.0 kW 230 - 240V Capacity 9 Litres Weight (full) 29kg Rated pressure 0MPa (0 bar) Minimum supply pressure 0.02MPa (0.2 bar) Maximum supply pressure 1.0MPa (10 bar) Nominal commissioning time 45 minutes... -
Page 4: General Installation
1.0 GENERAL INSTALLATION POINTS 1.1 Wherever possible the Supreme should be supplied directly from a rising main. If fed from a cold water feed cistern, the cistern must comply with the Water Regulations Guide (clause R27.2). It should be noted that water quality may be reduced when supplied from a cistern and additional forms of water pre-treatment may be necessary. -
Page 5: Installation Location
2.0 INSTALLATION - LOCATION 2.1 The Supreme stores and dispenses water at, or close to, boiling point at all times it is switched on. Due caution must be taken when choosing a location for the product to minimise misuse. It is... -
Page 6: Installation - Water Supply
4.0 INSTALLATION - WATER SUPPLY 4.1 A WRAS listed isolating valve should be fitted to the cold supply to facilitate servicing the heater. 4.2 Before connecting the unit the supply pipe must be thoroughly flushed out to ensure that foreign matter does not block or enter the solenoid valve. 4.3 The unit must be connected to a potable water supply using the food grade hose provided, in a manner which complies with UK water regulations. -
Page 7: Installation - Electrical Requirements
6.4 The installation, supply cable and circuit protection must conform to the latest BS7671 ‘Requirements for electrical installations’ (IEE Wiring Regulations). 6.5 If the Supreme is not used for significant periods of time running costs can be reduced by switching the unit off. It is recommended that this is done automatically by incorporating a suitable timeswitch in the supply to the unit. - Page 9 7.0 COMMISSIONING 7.1 Check that all electrical, water, and vent pipe connections have been made and are secure. 7.2 Turn on the water supply and then switch on the electrical supply. Ensure that the On/Off switch is in the On position. (Located at the rear).
-
Page 10: Maintenance
Misuse of such chemicals is not covered by the product warranty. 8.3 The Supreme incorporates an electronic scale conditioning function which will reduce the rate of scale deposition in hard water areas. - Page 11 Heatrae Sadia Service Department, telephone 0844 871 1535, fax 0844 871 1528. 9.4 To gain access to internal components, the lid must be removed. The lid ‘pops’ off in an upward motion. Beneath the lid there are four screws holding the steam trap in place.
- Page 12 9.5 Scale deposits should be removed from all internal surfaces, particularly the heating element, thermistor, and level sensors by gently tapping or scraping. If the deposits are soft, use a nylon pad and flush out. Abrasive cleaning materials containing scouring powders and detergents must not be used, as such materials can cause taste problems.
- Page 13 Heat transfer compound is also supplied with all replacement circuit boards. 9.9 Adjusting the Water Temperature Set Point The temperature potentiometer (Pot) is pre-set at Heatrae Sadia and will only require adjustment in exceptional circumstances. Contact Heatrae Sadia for advice.
-
Page 14: Fault Finding
10.0 FAULT FINDING YOUR HEATRAE SADIA SUPREME SHOULD GIVE TROUBLE FREE OPERATION. HOWEVER SHOULD A FAULT OCCUR THE TABLE BELOW SHOULD ALLOW MOST FAULTS TO BE IDENTIFIED. FAULT FINDING SHOULD ONLY BE CARRIED OUT BY A COMPETENT PERSON. Symptoms Possible Cause... -
Page 15: Spare Parts
11.0 SPARE PARTS The following comprehensive list of spare parts are available for your Supreme water heater. DO NOT REPLACE WITH PARTS NOT RECOMMENDED BY HEATRAE SADIA - THIS WILL INVALIDATE YOUR GUARANTEE AND MAY RENDER THE INSTALLATION DANGEROUS. Tap assembly............95 605 098 Draw off tap body ..........95 605 174... -
Page 17: User Instructions
When fully illuminated indicates that the stored water is hot enough to use. SERVICE See service section (section 9.0, page 11) for the service light status. 12.6 If the Supreme is not used for a few days the water may become “stale”. In these instances it is advisable to draw off the contents and discard the water at least twice to remove the “stale” water. This will ensure that “freshly” boiled water is used to make your drinks etc. -
Page 18: Environmental Information
GUARANTEE This Supreme water heater is guaranteed for a period of two years from the date of purchase, provided: 1. The unit has been installed in accordance with these instructions and all necessary inlet, vent, and electrical connections have been fitted correctly. -
Page 20: Spares Stockists
Advanced Water Company Ltd Unit DS Enterprise Way Vale Park, Evesham Worcs, WR11 1GS Tel: 01386 760066 Service: 0844 871 1535 Service Fax: 0844 871 1528 Service Email: heatraesadiaservice@ heateam.co.uk Heatrae Sadia Heating Hurricane Way Norwich NR6 6EA www.heatraesadia.com © 2012 36006156_issue_02...