Cleaning, Hygiene, Storage; Fault Fi Nding - Electrolux B2000 - 30 Instruction Manual

C l e a n i n g , h y g i e n e , s t o r a g e
Respect the safety instructions in § 3.1.
4 . I N B E T W E E N U S E
1
- Immerse the dirty parts of the tool in hot water.
4 . 2 A F T E R U S E
- Remove the mixer or whisk equipment from the motor assembly
(refer §3.4).
1 ) R e m o v e t h e M i x e r e q u i p m e n t c o m p l e t e l y :
- Push the shaft firmly on the coupling side so as to unclip the
assembly.
This should be dismantled over a table or a stable sup-
port so as to avoid injury when the shaft and the cutter
come out.
- Tap the non-cutting side of the cutter blade lightly using the
upper part of the tube to unscrew the cutter without injury.
2 ) R e m o v e t h e W h i s k e q u i p m e n t c o m p l e t e l y :
3 ) C l e a n i n g / S t e r i l i z a t i o n
a ) C l e a n i n g
- Do not immerse the Whisk or Mixer equipment.
- Do not clean the bearing bush and shaft of the Mixer or
the Whisk geared reducer in a dishwasher.
-
T h e s t r i p p e d t u b e , b l a d e a n d t w o w h i s k s
hot water and detergent - degreaser - disinfectant compatible
with the equipment materials or in a dishwasher.
To prevent damage to the plastic parts, after putting them
through a dishwasher wait for them to return to room tem-
perature before doing anything with them
4 . S T O R A G E
3
• Choose a place that is easily accessible to attach the wall
support (screws and rawl plugs not supplied).
- After cleaning, hang the motor unit and the Mixer and Whisk
equipment on the wall support.
F a u l t f i n d i n g
5 . 1 T H E M A C H I N E W I L L N O T S T A R T , C H E C K T H A T :
• The machine is plugged in.
• The electrical power supply to the socket is correct.
- The operator has pressed the two START buttons simultaneously.
• If low speed cannot be selected (BERMIXER only), check the
condition of the carbon brushes of the motor and change if
necessary, by removing the motor unit (see §6.1).
• If variable low speed (BERMIXER only) or high speed cannot
be selected, check that the variator is not defective (see §6.1).
5 . A B N O R M A L N O I S E :
2
• Stop and unplug the machine.
• Check the condition of the Mixer on a regular basis:
- If when operating there are vibrations, play in the shaft, wear
in the bearings or the shaft is out of true.
3 .
4
§ 3.3.
can be cleaned in
4 . 3
- Start it up for a few seconds and the tool will be cleaned
automatically.
-
T h e s h a f t a n d l o w e r b e a r i n g b u s h o f t h e M i x e r a n d t h e
g e a r e d r e d u c e r o f t h e W h i s k
- Rinse the various parts in clean water and leave them to dry
before sterilizing them.
- If necessary, wipe the motor assembly. Under no circumstan-
ces must drops of water be allowed to enter into the motor
assembly.
b ) S t e r i l i z a t i o n
T u b e :
After cleaning and each time before use, the lower bearing bush
must be removed for sterilization.
The parts to be sterilized are those in contact with the foods-
3 .
4
tuffs :
- the blade, (3),
- the sub-assembly (4) - not dismantled,
- the tube (5),
4 .
2 c
- the sub-assembly (6) - not dismantled.
Sterilization must be performed with equipment suited to this
purpose (UV, ozone, etc.) in accordance with the manufactu-
rer's instructions.
W h i s k :
- After cleaning and each time before use : geared reducer
4 .
2 d
housing and whisks in the same way as the tube.
Important:
- Keep the motor assembly away from sources of heat.
- Handle the machine carefully and avoid dropping or
banging it.
If the machine stops in mid-cycle:
- unplug it and leave to cool down so that the thermal
trip can reset.
If problems persist, contact the service department of your
local dealer.
If problems persist, contact the service department of your
local dealer.
3
will be cleaned with a brush.
B 2000 GB 09 02