Cleaning And Hygiene; Fault Fi Nding - Electrolux BE5 Manual

3. ACCESSORIES HUB
7
• A version is fi tted with a variable speed accessories hub (square
dimension 12 mm, type K) to drive the optional accessories:
3.
4a
• To fi t one of the accessories, proceed as follows:
- The beater must be stopped.
- Fit the accessory which corresponds to the work to be carried
out.
- Unscrew the lock screw U.
- Turn the cover L.
- Position the accessory and insert the conical endpiece N of
accessory P into the accessories hub M of the beater.
- Engage the square S into the drive shaft of the hub M by
pivoting accessory P.
- Position the pin R into the groove (T) and drive the accessory
home into the hub M.
- Tighten the lock screw U (clockwise
Recommendations for using the meat mincer
- Prepare the meat before inserting it into the mincer:
- Remove all bones and gristle.

Cleaning and hygiene

4. IN BETWEEN USE
1
• Remove the bowl and tool.
• With hot water and detergent - degreaser - disinfectant (if
working with greasy products), wash the inside of the bowl and
the tool, then rinse in clean water and dry.
4.2 AFTER USE
• Unplug the machine.
• Remove the bowl, tool and guard (
• Clean the bowl, tools and guard by immersing them in hot
water and detergent - disinfectant then rinse in clean water and
dry.
The bowl and tools can be washed in a dishwasher.
• Clean the planetary gear, tool holder shaft and cradle paying
particular attention to the bowl handles and the outside of the
whisk if necessary using a damp sponge and a detergent product,
then rinse.
• Check that the different parts have been cleaned correctly.
Fault fi nding
5. THE MACHINE WILL NOT START
1
• Check that :
- The machine is plugged in.
- The electrical power supply to the socket is correct.
- The safety guard is lowered.
- The bowl is in position on the cradle.
• If the mixer stops in mid-cycle:
The electronic variator has detected a fault (overload,
overheating, etc): unplug the appliance and wait a
minute before reconnecting it.
BE5 - BE8 GB 06 2015
- Cut the meat into long, thin pieces (about the same size as
your thumb).
- Put part of the meat in the cup of the mincer.hachoir
- Start up the beater by positioning button G between 7 and 9.
- Slide the pieces of meat into the chute one at a time. They will
get caught by the screw.
- Use the pusher (and only the pusher) if the piece of meat
does not get taken up by the screw. Do not fi ll up the chute
and subsequently force with the pusher as this does not
accelerate the mincing process but damages the machine.
).
• Clean the planetary gear housing, the toolholder spindle and
the protective guard with a damp sponge and a detergent - di-
sinfectant, then rinse in clean water
3.2 a.b.c.d.e).
• Do not use abrasive detergents, which could scratch the
surfaces.
Periodically: (at least once a month)
• Wipe and lightly grease the lifting and lowering pins with Vaseline
and the pins of the guard.
- The electronic variator limits the amount of current going to the
motor and reduces the speed if there is an overload. In this
case, reduce the speed or load.
- Reset the speed variator switch to zero before starting the
machine.
4
These optional accessories are designed to perform
accompanying work and not industrial quantities. Heavy
duty and forced use would damage your beater.
The machine must be stopped, before fi tting or
removing an accessory.
Note : Use cleaning products that are compatible with
the aluminium and plastic parts (polycarbonate)
Note: Check that the products used for cleaning are
compatible with the machine equipment.
Never clean the machine with a hose or high pressure cleaner
Do not put the machine in the dishwasher.
If the problem persists, contact the service department
of your local dealer..