Specifications; Carton Inventory; Safety Installation Information - Chamberlain CB24 Owner's Manual

C A R T O N I N V E N T O R Y
CB24K KIT
1x PVC – Box
1x CB24-Logic Board (pre-mount)
1x Charge transformer (pre-mount)
2x 12Volt Batteries & wires (pre-mount)
1x 771E IR-sensor
CB24R KIT
1x PVC – Box
1x CB24-Logic Board (pre-mount)
1x Run transformer (pre-mount)
1x IR-sensor (771E)
CAK-1 COMMON ACCESSORY KIT
1x RF module 433.92MHz
2x Transmitter 3-channel 94335E
1x Key switch
1x Flashing Light (FLA24-2)
1x Antenna
S A F E T Y I N S T A L L A T I O N I N F O R M A T I O N
Warning - To reduce the risk of SEVERE INJURY or DEATH from an incorrect installation:
1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The gate operator is only one
component. Each gate system is specifically designed for an individual application.
2. Gate operating system designers, installers and users must take into account the possible hazards associated with each individual application.
Improperly designed, installed or maintained systems can create risks for the user as well as the bystander. Gate systems design and installation
must reduce public exposure to potential hazards.
3. A gate operator can create high levels of force in its function as a component part of a gate system. Therefore, safety features must be
incorporated into every design. Specific safety features include:
• Gate Edges
• Screen Mesh
4. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage class of the gate.
b. All openings of a horizontal swing gate are guarded or screened from the bottom of the gate to a minimum of
4' (1.2 m) above the ground to prevent a 2 1/4" (6 cm) diameter sphere from passing through the openings anywhere in the gate, and in that
portion of the adjacent fence that the gate covers in the open position.
c. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers.
5. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening.
6. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing
to reduce the risk of entrapment. Swinging gates shall not open into public access areas.
7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.
8. Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating the controls.
9. Controls intended to be used to reset an operator after 2 sequential activations of the entrapment protection device or devices must be located in
the line of sight of the gate, or easily accessible controls shall have a security feature to prevent unauthorized use.
10. All warning signs must be installed where visible, on each side of the gate.
11. For a gate operator utilizing a non-contact sensor:
a. Reference owner's manual regarding placement of non-contact sensor for each type of application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a
moving gate or barrier.
12. For a gate operator utilizing a contact sensor such as an edge sensor:
a. A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate operator is not
subject to mechanical damage.
b. A wireless contact sensor such as the one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions
shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar
obstruction. A wireless contact sensor shall function under the intended end-use conditions.
c. One or more contact sensors shall be located at the leading edge, trailing edge and post mounted both inside and outside of a vehicular
horizontal slide gate.
d. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
e. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a
swing gate is greater than 6" (15 cm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on the
bottom edge.
• Guards for exposed rollers
• Vertical Posts
3
I N V E N T O R Y & S P E C I F I C A T I O N S
LYN300-24 Wing Gate Operator 24Volt/250kg/2.5m
LYN400-24 Wing Gate Operator 24Volt/250kg/4.0m
SCS300-24 Wing Gate Operator 24Volt/250kg/3.0m
LA400-JB40 Extensioncable Kit 12m (page 6)
600206-24 Solar Panel 24 Volt
041ASWG-0479 Post bracket for round posts/piece
50-19503 Post bracket for gates opening to outside
(push to open)/piece
Battery Charger Supply . . . . . . . . . . . . . . . . . . . . . . . . .26Vac, 29VA
Solar Panel Supply (Optional) . . . . . . . . . . . . .27.4V, 9W (Minimum)
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-20
Battery 12V/7AH . . . . . . . . . . . . . . . . . . . . . . . . . . . .-15
Electronic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP44
Main Supply (Control) Dedicated
Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V~240V/50~60Hz
Absorbed Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75 Watts
Protection Fuse Gate 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ATC 10A
Protection Fuse Gate 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ATC 10A
Protection Fuse Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . .ATC 20A
• Photoelectric Sensors
• Instructional and Precautionary Signage
o C to + 55 o C
o C to + 55 o C