Quinny Speedi Instructions For Use & Warranty page 5

>> EN
Preparing the pushchair for use and instructions for use
The illustration numbers correspond to the text (see
illustrations on pages 3 to 5).
Please note: The left and right sides are as seen from the
handlebar/back of the Quinny Speedi.
Unfolding / folding
To unfold
(1) The frame has been secured by means of a
transport safety lock to prevent it from unfolding
during transport. Release the lock by pulling the
left handlebar safety lock in the direction of the
arrow.
(2+3) Pull the handlebar upwards until it "clicks" into the
handlebar safety lock.
Check this by pushing down on the handlebar.
(4) Make sure that the handlebar safety locks are
released (1). Adjust the handlebar to the desired
height (2).
(5) Click both handlebar safety locks back into place.
Placing / removing the wheels
The 2 wheels with the brake cylinder should be mounted as
rear wheels.
(6+7) Press the button in the middle of the hubcap while
pushing the axle into the axle opening.
Check to make sure the wheel is secure.
(8) Place the wheel into the front fork by pressing
the button (1) and then clicking the wheel into the
opening on the front (2).
(9) The swivel wheel can be adjusted into 2 different
positions: fixed or swivelling (1). To lock it into the
fixed position, rotate the swivel lock until 2 straight
arrows appear in the display (2).
• The swivelling front wheel will lock itself the
moment the pushchair is pushed forward.
• Check the tyre pressure and inflate the tyre
if necessary (see maintenance section for the
maximum tyre pressure allowance).
(10+11) To remove the rear wheels, press the button on the
hubcap and pull the wheel out of the axle opening.
• To remove the swivel wheel, press the button and
pull the wheel out of the axle opening.
Folding
(9) IMPORTANT: The swivel wheel must be in a
swivelling position before folding (1).
• IMPORTANT: Always remove the Quinny Dreami
carrycot or Maxi-Cosi car safety seat before
folding.
• Apply the brake on the Quinny Speedi (see Using
the parking brake).
• Fold up the sun canopy (see Using the sun canopy).
• Make sure the footrest is in the lowest position
(see Footrest).
(12) Click open both handlebar safety locks (1). Push in
the release button on the handlebar (2).
(13) Push down the handlebar until the stop, and then
further downwards until you hear a clearly definite
"click".
• Make sure the transport safety lock clicks over the
catch again.
• Remove the wheels to make the pushchair even
smaller.
• IMPORTANT: It is advisable to remove the sun
canopy before folding the pushchair (see Using the
sun canopy).
10
Instructions for use
For use with the Quinny Dreami carrycot (up to 9 kg) and
the Maxi-Cosi car safety seat (up to 13 kg).
Placing / removing the adapters
(14) Remove both guards by pushing in the button (1)
whilst simultaneously pushing the guards upwards
(2).
(15) Slide the adapter marked R into the right-hand side
and the adapter marked L into the left-hand side of
the adapter attachment.
Continue sliding until you hear a "click".
Check to make sure the adapters are secure.
(16) To remove the adapters, push in the spring-loaded
button (1) whilst simultaneously pushing the
adapters upwards (2).
Place both guards back onto adapter attachments.
Placing / removing the Quinny Dreami carrycot and
Maxi-Cosi car safety seat
• Apply the brake on the Quinny Speedi (see Using
the parking brake).
(17/19) Place the carrycot / car safety seat onto the
adapters with the foot end between the sides of
the handle.
Check to make sure the carrycot / car seat is
secured by lifting it up by the handles.
(18/20) To remove, place your thumbs on the control
buttons on both sides of the carrycot / car safety
seat (1). Push in the buttons while lifting the
carrycot / car safety seat from the Quinny Speedi
(2).
EN <<
When used as a pushchair
Placing / removing the pushchair seat
• Apply the brake on the Quinny Speedi (see Using
the parking brake).
(21) To remove the pushchair seat undo the velcro
under the foot rest (1) and undo the clasp (2) and
the press stud (3).
(22) Open the press studs on the bottom (1) and undo
the velcro near the handlebar safety lock (2).
• Remove the pushchair seat from the frame.
• When placing the pushchair seat back onto the
frame, make sure to re-attach all press studs, clasps
and velcro.
• IMPORTANT: Make sure you remove the adapters
before attaching the pushchair seat (see Placing /
removing the adapters).
• Check to make sure everything is securely fastened
by lifting up the pushchair seat.
Safety harness
• Apply the brake on the Quinny Speedi (see Using
the parking brake).
• Make sure the safety harness is loosened before
placing your child (carefully!) into the seat.
(23) Slide the buckle sections together (1) and fasten
the lap and shoulder belts into the crotch strap by
clicking the buckle sections into the fastener (2).
(24) Adjust the belts to the size of your child by
lengthening or shortening the belts using the
clasps.
11