Kenwood TK-5210 K Service Manual page 41

■ Frequency and Signaling
The transceiver has been adjusted for the frequencies
shown in the following table. When required, readjust them
following the adjustment procedure to obtain the frequencies
you want in actual operation.
• Test Frequency (MHz)
Channel No. RX Frequency
1 155.10000
2 136.10000
3 173.90000
4 155.00000
5 155.20000
6 155.40000
7~16
• Test Signaling
Signaling RX Signaling
No.
1 None
2 None
3 QT 67.0Hz
4 QT 151.4Hz
5 QT 210.7Hz
6 QT 254.1Hz
7 DQT 023N
8 DQT 445N
9 DQT 754I
10 DTMF Code "159D"
11 None
12 None
13 2-Tone:
A : 304.7Hz
B : 3106.0Hz
14 Single Tone : 979.9Hz
15 None
16 MSK
Sync : 0x052B
Data : 0x230960C6AAAA Data : 0x230960C6AAAA
CRC : 0xC4D7
17 NAC 293
18 NAC 023
19 NAC 5EA
20 1011Hz Tone Test Pattern 1011Hz Tone Test Pattern APCO
21 NAC 293
22 NAC 293
23 NAC 293
24 NAC 293
25 NAC 293
26 NAC 293
ADJUSTMENT
TX Frequency
155.00000
136.00000
173.95000
155.00000
155.20000
155.40000
- -
TX Signaling APCO/
Analog
None Analog
100Hz Square wave Analog
QT 67.0Hz Analog
QT 151.4Hz Analog
QT 210.7Hz Analog
QT 254.1Hz Analog
DQT 023N Analog
DQT 445N Analog
DQT 754I Analog
DTMF Code "159D" Analog
DTMF Code "9" Analog
1633Hz Single Tone Analog
2-Tone: Analog
A : 304.7Hz
B : 3106.0Hz
Single Tone : 979.9Hz Analog
MSK PN Pattern Analog
MSK Analog
Sync : 0x052B
CRC : 0xC4D7
NAC 293 APCO
NAC 023 APCO
NAC 5EA APCO
Silence Pattern APCO
Calibration Pattern APCO
Transmitter Test Pattern APCO
Symbol Rate Pattern APCO
Low Deviation Pattern APCO
Fidelity Pattern APCO
Panel Tuning Mode
The transceiver is adjusted in this mode.
For the K model (without LCD), perform "Tuning mode"
using the KPG-95D.
■ Preparations for tuning the transceiver
Before attempting to tune the transceiver, connect the
unit to a suitable power supply.
Whenever the transmitter is turned, the unit must be con-
nected to a suitable dummy load (i.e. power meter).
The speaker output connector must be terminated with a
8Ω dummy load and connected to an AC voltmeter and an
audio distortion meter or a SINAD measurement meter at all
times during tuning.
■ To enter the Panel Tuning Mode
Press the [Side3] key in the panel test mode.
Use the [B] key to write tuning data through tuning modes,
and the [C] and [D] keys to adjust tuning requirements (1 to
256 appeares on LCD).
Use the [A] key to select the adjustment item through tun-
ing modes. Use the [Side1] key to adjust 3 or 5 reference level
adjustments, and use the [Concentric switch] to switch be-
tween Wide/Narrow/APCO. (Position "A":Wide, Position
"B":Narrow, Position "C":APCO)
• LCD display in the panel tuning mode
W: Wide
N : Narrow
A : APCO
W
Balance
NXT SET
Adjustment
item
TK-5210
(K2 and K3 models only)
LO
256
Adjustment
value(1~256)
41