Sony BDP-CX7000ES Service Manual page 96

BDP-CX7000ES
QQ
3 7 63 1515 0
Pin No. Pin Name
Y18, Y19 GND
Y20 PLMVGND
Y21 PLMVVDD
Y27 GND
Y28 ETMDC
Y29 ETMDIO
Y30 ETREFCLK
Y31 HDSDA
Y32 TX0N
Y33 TX0P
AA1 UMA8
AA2 UMCSB0
AA3 UMVDD18
AA4 UMRASB
AA5 GND
AA6 UMCSB1
AA7 GND
AA13 PLURVDD
AA14 PLUMVDD
AA15 GND
AA16 VDD10
AA17 GND
AA18 VDD10
AA19 GND
AA20 PLSVGND
AA21 PLSVVDD
AA27 ETRXER
TE
L 13942296513
AA28,
ETRXD0, ETRXD1
AA29
AA30 ETCRS
AA31 HHPD
AA32,
AVCC
AA33
AB1 UMODT0
AB2 GND
AB3 UMA15
AB4 UMDQ22
AB5 UMODT1
AB6, AB7 UMVDD18
AB27 GND
AB28,
ETTXD0, ETTXD1
AB29
AB30 ETTXEN
AB31 AGNDH
AB32 TXCN
AB33 TXCP
AC1 GND
AC2 to UMDQ23, UMDQ21,
AC4 UMDQ20
AC5 GND
AC6 UMVDD18
AC7 GND
AC27 VDD3
AC28 to
www
GND
AC30
AC31 to
AGNDH
AC33
.
AD1 UMDQS2
AD2 GND
AD3 UMDM2
AD4 UMDQ17
96
http://www.xiaoyu163.com
I/O
- Ground terminal
- Ground terminal (for PLL)
- Power supply terminal (+1.05V) (for PLL)
- Ground terminal
O Management clock signal output to the ethernet interface
I/O Two-way management data bus with the ethernet interface
I System clock signal input terminal (50 MHz)
I/O Two-way data bus terminal
O TMDS data (negative) output terminal
O TMDS data (positive) output terminal
O Address signal output to the SD-RAM
O Chip select signal output to the SD-RAM
- Power supply terminal (+1.8V)
O Raw address strobe signal output to the SD-RAM
- Ground terminal
O Chip select signal output to the SD-RAM
- Ground terminal
- Power supply terminal (+1.05V) (for PLL)
- Power supply terminal (+1.05V) (for PLL)
- Ground terminal
- Power supply terminal (+1.05V)
- Ground terminal
- Power supply terminal (+1.05V)
- Ground terminal
- Ground terminal (for PLL)
- Power supply terminal (+1.05V) (for PLL)
I Error signal input from the ethernet interface
I Serial data input from the ethernet interface
I Carrier sense input from the ethernet interface
I Hot plug detection signal input terminal
- Power supply terminal (+1V) (analog system) (for HDMI)
O ODT signal output to the SD-RAM
- Ground terminal
O Address signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
O ODT signal output terminal
- Power supply terminal (+1.8V)
- Ground terminal
O Serial data output to the etherner interface
O Enable signal output to the etherner interface
- Ground terminal (analog system) (for HDMI)
O TMDS clock signal (negative) output terminal
O TMDS clock signal (positive) output terminal
- Ground terminal
I/O Two-way data bus with the SD-RAM
- Ground terminal
- Power supply terminal (+1.8V)
- Ground terminal
- Power supply terminal (+3.3V)
- Ground terminal
x ao u163
y
- Ground terminal (analog system) (for HDMI)
i
O Data strobe signal (positive) output to the SD-RAM
- Ground terminal
O Data mask signal output to the SD-RAM
I/O Two-way data bus with the SD-RAM
http://www.xiaoyu163.com
2 9
8
Description
Not used
Not used
Not used
Q Q
3 6 7 1 3 1 5
Not used
Not used
Not used
Not used
co
.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9