Sony BDP-CX7000ES Service Manual page 91

QQ
3 7 63 1515 0
Pin No. Pin Name
E7 PCICBEB1
E8, E9 PCIAD9, PCIAD3
E10
E11
VODC4, VODC2,
E12 to E14
E15
E16, E17 IPODC3, IPODC5
E18 SAVDDTIO
E19 SAVDDIG
E20
E21
E22
E23
E24
E25
E26
E27
E28
E29
E30, E31 AO0BD1, AO0BD2
E32
E33 AO1MCK
F1
F2
F3 PCIREQB0
F4 PCIIDSEL
TE
L 13942296513
F5 PCICBEB3
F6 PCIDEVSELB
F7
F8 PCICBEB0
F9
F10
F11, F12 VODY8, VODY5
F13
F14
F15
F16 AOHBCK
F17 SAGNDANA
F18 SAVDDTIO
F19 SAVDDIG
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31 AO1LRCK
www
F32
F33
G1
G2 .
PCIAD28, PCIAD26,
G3 to G8 PCIAD31, PCIAD15,
PCIAD16, PCIAD10
http://www.xiaoyu163.com
I/O
I/O Command and byte enable signal input/output with the USB interface
I/O Two-way address and data bus with the USB interface
VODY3 O Digital video (Y) signal output to the digital video format converter
VODC0 O Digital video (Cb/Cr) signal output terminal
O Digital video (Cb/Cr) signal output to the digital video format converter
VODC7
AOHBD3 O Audio signal output to the HDMI transmitter
I/O Not used
- Power supply terminal (+1.8V)
- Power supply terminal (+1.05V) (digital system)
GPIO32 I/O Not used
GPIO23 I Clock signal input terminal (for JTAG)
GPIO31 I/O Not used
GPIO26 I Reset signal input terminal (for JTAG)
GPIO16 O Reset signal output to the D/A converter
GPIO15 O Chip select signal output to the D/A converter
GPIO2 O Chip select signal output terminal
GPIO1 O Chip select signal output to the component interface
GND - Ground terminal
TMODE3 I Test terminal
O Audio signal output to the D/A converter
AO1BD O Audio signal output to the D/A converter
O Master clock signal output to the D/A converter
SYSXI I System clock signal input terminal (27 MHz)
GND - Ground terminal
I Request signal input from the USB interface
I Initialization device selection signal input from the USB interface
I/O Command and byte enable signal input/output with the USB interface
I/O Device selection signal input/output with the USB interface
PCIAD13 I/O Two-way address and data bus with the USB interface
I/O Command and byte enable signal input/output with the USB interface
PCIAD4 I/O Two-way address and data bus with the USB interface
VODY1 O Digital video (Y) signal output terminal
O Digital video (Y) signal output to the digital video format converter
VODC3 O Digital video (Cb/Cr) signal output to the digital video format converter
VODC9 O Digital video (Cb/Cr) signal output to the digital video format converter
IPODC1 I/O Not used
O Bit clock signal output to the HDMI transmitter
- Ground terminal (analog system)
- Power supply terminal (+1.8V)
- Power supply terminal (+1.05V) (digital system)
GPIO27 I Debug interrupt signal input terminal (for JTAG)
GPIO30 I Interrupt signal input from the USB interface
GPIO25 I Mode selection signal input terminal (for JTAG)
GPIO24 O Data output terminal (for JTAG)
GPIO17 O Audio muting on/off control signal output terminal
GPIO12 O Reset signal output to the FPGA, HDMI interface and component interface
GPIO7 I/O Not used
VRVDD - Power supply terminal (+1.05V)
TMODE5 I Test terminal
TEST I Test terminal
S2DOUT O Serial data output to the system controller
O L/R sampling clock signal output to the D/A converter
AO1BCK O Bit clock signal output to the D/A converter
VDD3 - Power supply terminal (+3.3V)
x ao
y
SYSXO O System clock output terminal (27 MHz)
GND i - Ground terminal
I/O Two-way address and data bus with the USB interface
http://www.xiaoyu163.com
8
Not used
Not used
Not used
Q Q
3 6 7 1 3
Not used
Not used
Not used
u163
.
BDP-CX7000ES
2 9 9 4 2 8
Description
Not used
Not used
"L": reset
1 5 0 5 8 2 9 9 4
No used
Not used
Not used
"L": muting on
m
co
9 9
2 8 9 9
"L": reset
91