Jenn-Air JBC7624BS Design And Planning Manual page 12

____________________________________________________________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________ __________________________________________________
____________________________________________________________________________________________________________________________________________________ 30" COMBINATION MICROWAVE/WALL OVENS
____________________________________________________________________________________________________________________________________________________
JMW3430W, JMW2430W, JMW2330W – 29 ⁄ " x 43
3
4
_______________________________________________ ____________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________ __
OPENING/CLEARANCE DIMENSIONS
____________________________________________________________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________________________
_______________________________________________________________________________________________ _____________________________________________________
A A
F
G
H
D D
C
C*
B B
Conduit Channel
A
B
E E
e e
F F
C
FRONT VIEW SIDE VIEW
Power Supply Location
BACK VIEW
22
⁄ " x 26 ⁄ "
1 3
8 4
A
MODEL #
A Width of cabinet (min.)
B Width of cutout
C Height of cutout
Top of cutout to bottom
I
D
of upper cabinet door (min.) 2 ⁄ " (5.2 cm)
1
16
D
Top Cleat*
Bottom of cutout to top
E
Back of Cabinet
of lower cabinet door (min.)
A
C*
F Bottom of cutout to floor
B
C
G Depth of cutout (min.) B
D
D e Recommended junction box location
E
ELECTRICAL REQUIREMENTS
⁄ " (1.9 cm) ⁄ " (1.9 cm)
3 3
4 4
240 volt, 40-amp fused, grounded circuit is required. A dedicated Side Cleat* Side Cleat*
circuit is recommended.
The length of conduit provided is for serviceability. Do not cut the 1 ⁄ " (3.8 cm)
1
2
Platform*
conduit. The junction box should be located 3" (7.6 cm) maximum
E
below the support surface. Drill a 1 ⁄ " (3.4 cm) minimum diameter
1
4
hole in the left rear corner of the support surface for access to the
e
G
junction box.
e
Bottom of Cabinet
F
e
____________________________________________________________________________________________________________________________________________________
Power Supply Location ____________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________ __________________________________________________
____________________________________________________________________________________________________________________________________________________ 30" COMBINATION MICROWAVE/WALL OVENS – FLUSH INSTALLATION
____________________________________________________________________________________________________________________________________________________
JMW3430W, JMW2430W, JMW2330W – 29
_______________________________________________ ____________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________ __
OPENING/CLEARANCE DIMENSIONS
____________________________________________________________________________________________________________________________________________________
____________________________________________________________________________________________________________________________________________________
_______________________________________________________________________________________________ _____________________________________________________
JMW3430W
JMW2430W
JMW2330W
A
K
in cm
L L
30 76.2
28 ⁄ 72.4
1
2
41 1 ⁄ 104.8
4
M
2 5.1 N
2
3
O
Top Cleat*
P
1 1 ⁄ 3.8
2
A
4 ⁄ - 11.7-
5
8
B
19 ⁄ 48.9
1
4
24 61.0
C
2" (5.1 cm) D
Top Cleat*
A
B
⁄
3 ⁄ " (1.9 cm) ⁄ 3 " (1.9 cm)
3 4
4 4
Side Cleat* Side Cleat*
C Side Cleat*
D
1 ⁄ " (3.8 cm)
1
2
Platform*
3 ⁄ " (1.9 cm) 3 ⁄ " (1.9 cm)
4 4
Side Cleat* Side Cleat*
1 ⁄ " (3.8 cm) e
1
2
Platform*
G
E
e
E FRONT VIEW
A
B C
D
E
F
J
2" (5.1 cm)
e
Top Cleat*
A
B
G
C
H
D
⁄ " (1.9 cm) ⁄ " (1.9 cm)
3 3
4 4
I
Side Cleat* Side Cleat*
1 1 ⁄ " (3.8 cm)
2
Platform*
E
TOP VIEW
* Cleats and platform must be recessed 1" (2.5 cm) from the front of the cabinet.
Power Supply Location
Power Supply Location
⁄ " x 43 ⁄ " x 24 ⁄ " (depth without handles)
3 1 3
4 8 4
⁄ " (7.0 cm) 2 1 ⁄ " (5.2 cm)
4 16
Top Cleat*
A
B
C
D
" (1.9 cm)
3 ⁄ " (1.9 cm)
4
Side Cleat*
1 ⁄ " (3.8 cm)
1
2
Platform*
A
B F
e
E
E
F
SIDE VIEW
Power Supply Location
F
Side Cleat* Side Cleat*
1" (2.5 cm)
BACK VIEW
JMW3430W
JMW2430W
MODEL # JMW2330W
in cm
A Width of flush inset cutout (min.) 30 76.2
B Width of opening (min.) 28 ⁄ 72.4
1
2
C Height of flush inset cutout (min.) 44 ⁄ 113.8
13
F 16
G
D Height of opening (min.) 41 ⁄ 104.8
1
4
H
2 ⁄ " (7.0 cm)
3
4
4 ⁄ - 11.7-
5
Top Cleat*
I 8
E Bottom of cutout to floor
19 ⁄ 48.9
1
4
F Depth of cutout (min.) 25 63.5
A
Back of Cabinet
e Recommended junction box location
B
ELECTRICAL REQUIREMENTS
C
240 volt, 40-amp fused, grounded circuit is required. A dedicated
D
circuit is recommended.
D
The length of conduit provided is for serviceability. Do not cut the
⁄ " (1.9 cm) ⁄ " (1.9 cm)
3 3
4 4 E
conduit. The junction box should be located 3" (7.6 cm) maximum
Side Cleat* Side Cleat*
below the support surface. Drill a 1 Conduit Channel ⁄ " (3.4 cm) minimum diameter
1
4
hole in the left rear corner of the support surface for access to the
1 ⁄ " (3.8 cm)
1
2
junction box.
Platform*
FLUSH INSTALLATION REQUIREMENTS
A 25" (63.5 cm) minimum cutout depth is required. e
These dimensions will result in a 3 ⁄ " (1.0 cm) reveal on the top,
8
E
a ⁄ " (0.3 cm) reveal on the sides and a 1 ⁄ " (3.5 cm) reveal on the
1 3
8 8
bottom of the wall oven.
The front face of the cleats and platform will be visible and should
Bottom of Cabinet
be treated as a finished surface.
C
F
23