NAPCO GEM-P1632 Installation Instructions Manual page 5

01
INTERIOR BYPASS FIRE/TBL
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
proceed. NOTE: If you are programming a 2 Area system, enter the total number of zones required for Areas 1 & 2. The
Direct Address Program Mode can then be used to remove zones from Area 1 and place them in Area 2. See Zone
Options. If Programming a Wireless Only system, or using wireless only on Zones 9-32, enter the total number of zones
in system. Enter the transmitter points in the RF Transmitter section of the Easy Menu Driven Programming Mode.
03
INTERIOR BYPASS FIRE/TBL
FIRE/TBL
INTERIOR BYPASS
(Press YES or NO)
04
INTERIOR BYPASS FIRE/TBL
FIRE/TBL
INTERIOR BYPASS
(Press YES or NO)
05
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(Press YES or NO)
06
GEMINI
SYSTEM ARMED
ENT A1
01/01/97 12:00AM
INTERIOR BYPASS FIRE/TBL
NEXT/YES
A 1 2 3 E
D
PRIOR/NO
B 4 5 6 F
AREA
C 7 8 9 0 G
COMPUTERIZED SECURITY SYSTEM
R
BYPASS FIRE/TBL
INTERIOR
(Yes or No)
Programming the GEM-P816 & GEM-P1632
Total Number of Zones in Area 1
A
Press the
programmed for Area 1. Valid entries are from 01 to 32. Directly enter the total
SYS TBL CHIME
number of zones, including leading zeros. Use number buttons
9
. NOTE: Press the
groups of 4 zones each (after the first 8 zones), and will automatically round up
to the next group of 4. For example, if you enter 18, it will automatically
SYS TBL CHIME
convert this to 20 zones. Press
Panel Zone Doubling?
A
Press the
or greater, press YES (
SYS TBL CHIME
panel's hard wired zones from 8 to 16. The 16 zones will no longer be EOL
zones, but will be designated for Normally Closed devices only. The terminal
for Zone 1 will now support Zones 1 and 9 with the use of the supplied EZ
SYS TBL CHIME Zone Doubling
Installation Instructions). If Panel Zone doubling is not desired, press NO
E
( ). NOTE: Answer NO for GEM-P816
Fire Zones in Area 1
button and then directly enter the zone number of any zones which are to be
used as Fire Zones (both 2-wire, 4-wire or wireless). Valid entries are from 01
SYS TBL CHIME
to 32. Directly enter each zone number, including leading zeros, and press
J
to save, and then repeat for any additional zone(s). Press NEXT (
button to proceed.
SYS TBL CHIME
2-Wire Fire Zones in Area 1
A
button and then directly enter the zone number of any Fire Zones (from
previous question) which are to be used with 2-wire smoke detectors. The
SYS TBL CHIME
only valid entries are 07 and 08. Directly enter each zone number, including
leading zeros. Press
NOTE: Only zones which have been designated as Fire Zones may be pro-
SYS TBL CHIME
grammed as 2 Wire Fire zones. Press NEXT (
NOTE: JP3 must be set to "2-WF" position for 2-wire fire zones for zones 7
and 8 (refer to Installation Instructions).
Report all Zones to Central Station?
Press YES (
F
( ) button for no zones to report (LOCAL SYSTEM).
SYS TBL CHIME
SYS TBL CHIME
button and then directly enter the total number of zones to be
0
button for a zero. The system is based on
J
to save. Press NEXT (
(Appears for New Panel Only) (GEM-P1632 only)
button. If the total number of zones in Area 1 entered was 16
E
) to effectively double the capacity of the control
TM
resistors, E & Z supplied. (Refer to Wiring Diagram and
(Appears for New Panel Only) Press the
(Appears for New Panel Only) Press the
J
to save and then repeat for any additional zone(s).
E
) button for all zones to report to central station; press NO
(Appears for New Panel Only)
1
E
) button to
E
) button to proceed.
(Appears for New Panel Only)
through
A
E
)
5