NAPCO GEM-P1632 Installation Instructions Manual page 10

01
BYPASS
INTERIOR
BYPASS
INTERIOR
(Direct Entry)
A
1 Press the button and then press
entries are from 08 to 24 in multiples of 4.
2
2 Press and press
If no zones are to programmed for Area 2, press
3 If Area 2 is to be programmed, press
programmed for Area 2.
2
4 Press and press
Note: the first zone of Area 1 (and Area 2, if selected) will automatically be programmed as an Exit/Entry zone with an
entry delay of 30 seconds and an exit delay of 60 seconds. The second zone will be programmed as an Exit/Entry
Follower Zone. In a single-area system, Zone 8 will be programmed as a 2-Wire Fire Zone (set Jumper JP7 to configure
zone 8 for 2 Wire Fire). In a two-area system, zones 7 and 8 will be programmed as 2-Wire Fire Zones and will be
common to both areas (set Jumper JP7 to configure zone 7 and 8 for 2 Wire Fire).
02
INTERIOR BYPASS
INTERIOR BYPASS
(Yes or No)
03
INTERIOR BYPASS
INTERIOR BYPASS
(Direct Entry)
04
INTERIOR BYPASS
INTERIOR BYPASS
(Direct Entry)
For Central Station Telephone and Account Numbers: Use number buttons
G0
for a zero and
Dial-Tone Detection = "E". Pressing the
10
Programming the GEM-P3200 & GEM-P9600
Total Number of Zones and Keypads in Area 1.
Total Number of Zones and Keypads in Area 2.
(Appears for New Panel Only)
FIRE/TBL SYS TBL CHIME
Press
FIRE/TBL SYS TBL CHIME
select # of
zones in Area 1
3
3
to select the total number of keypads to be programmed for Area 1.
2
3
to select the total number of keypads to be programmed for Area 3.
Report all Zones to Central Station?
Press YES (
F
(
FIRE/TBL SYS TBL CHIME
FIRE/TBL
SYS TBL CHIME
Central Station Receiver 1 Telephone Number
Press the
number of up to 16 digits including prefix, if necessary, for receiver 1.
FIRE/TBL SYS TBL CHIME
FIRE/TBL
SYS TBL CHIME
NOTE: Central Station Receiver 2 and 3 Telephone Numbers can be entered
in Direct Address Programming. See CS Reporting Options.
Press
Central Station Receiver 1 Account Number
Press the
four digits.
FIRE/TBL SYS TBL CHIME
NOTE: Central Station Receiver 2 and 3 Account Numbers can be entered in
FIRE/TBL
SYS TBL CHIME
Direct Address Programming. See CS Reporting Options.
Press Jto save. Press NEXT (
G 1
through
0
button will produce a blank space (•).
2
3 to Press 3 to
select # of
K/Ps in Area 1
to select the total number of zones to be programmed for Area 1. Valid
J
to save followed by NEXT (
3
and then press to select the total number of zones to be
E
) button for all zones to report to central station; press NO
) button for no zones to report (LOCAL SYSTEM).
A
button and using the number buttons, directly enter telephone
Central Station Receiver 1 Telephone Number
J
to save . Press NEXT (
A
button and then directly enter an account number of up to
Central Station Account #
G 5
for letters B–F, respectively. NOTE: Pre-Dial Delay = "D";
2 2
Press 3 to
select # of
zones in Area 2
E
) to proceed.
(Appears for New Panel Only)
E
) button to proceed.
E)
button to proceed.
1 9
through
J
Press 3 to
select # of
K/Ps in Area 2
for digits 1–9; press