NAPCO GEM-P1632 Installation Instructions Manual page 11

05
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(Direct Entry)
DATA CS RECEIVER 1 FORMAT
ENTRY
•(blank) Ademco Slow, Silent Knight Slow
1 Sescoa, Vertex, DCI, Franklin Fast
2 Radionics Fast
3 Silent Knight Fast
06
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(
Direct Entry)
1 Enter the User Number to be programmed, including leading zeros. Use the number buttons
2 Enter a User Code of up to 6 digits. Use the number buttons
G0
for each blank.
3 Enter the User Options. Refer to the User Option table below.
4 Enter the Authority Level. Refer to the Authority Level table below.
5 If this code is to be used to activate a door strike, assign the User to the appropriate access control keypad from the
Access Control Keypad table below.
User # User Code
USER OPTIONS
DATA BLOCKED USER BYPASS
ENTRIES VIEW PROGRAM
blank (•) DISABLED
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8
9 Y
0 Y
B Y Y
C Y
D Y Y
E Y Y
F Y Y Y
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
J
and press to save. Similarly, to cancel a code, blank out each number of the code press
Programming the GEM-P3200 & GEM-P9600
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number
1
buttons
SYS TBL CHIME
for a blank space (•). Press
respectively. Press
SYS TBL CHIME
NOTE: Central Station Receiver 2 and 3 Formats can only be entered in Direct
Address Programming. See CS Receiver Options.
DATA
ENTRY
4
5
8
9
Enter User Codes
For default program, enter up to 8 User Codes for Area 1 (Users 1 - 8) and up
to 8 User Codes for Area 2 (Users 9 - 16) . Press the (
SYS TBL CHIME
set the cursor to the User Number.
When programming User Options, Authority Level and Access Keypads:
SYS TBL CHIME
Option
DATA AUTHORITY
OVERVIEW ENTRIES LEVEL
blank (•) NONE
1 LEVEL 1
2 LEVEL 2
3 LEVEL 3
4 NONE
5 LEVEL 1
6 LEVEL 2
7 LEVEL 3
Y
8 NONE
Y
9 LEVEL 1
Y
0 LEVEL 2
Y
Y
B LEVEL 3
Y
Y
Y
9
through . NOTE: Press
G 1
J
to save. Press NEXT (
CS RECEIVER 1 FORMAT
Radionics, DCI, Franklin Slow
Universal High Speed
Radionics BFSK
FBI 4/3/1
"A" = G 0 ; "B" = G 1 ; "C" = G 2 ;
"D" = G 3 ; "E" = G 4 ; "F" = G 5 .
0
through
Level Access Control
ACCESS CONTROL KEYPADS
COD E
DATA
TYPE
ENTRIES
ARM/DISARM
blank (•)
ARM/DISARM 1
2
ARM/DISARM
3
ARM/DISARM
4
ARM ONLY
5
ARM ONLY
6
ARM ONLY
7
ARM ONLY
SERVICE
SERVICE
SERVICE
SERVICE
G0
for a zero and
G 4
through
E
) button to proceed.
DATA CS RECEIVER 1 FORMAT
ENTRY
0 Radionics Modem 2
B SIA
C Ademco Point ID
D Ademco Expres
E Pager
A
0
9
to enter the code followed by
ACCESS CONTROL KEYPADS
K.P. 5 K.P. 6 K.P. 7 DATA K.P. 1
ENTRIES
NONE blank (•)
Y
1
Y
2
Y Y 3
Y
4
Y Y 5
Y Y 6
Y Y Y
7
8
9
0
B
C
D
E
F
J
to save.
0
for letters B–E,
) button once to
9 .
through
K.P. 2 K.P. 3 K.P. 4
NONE
Y
Y
Y Y
Y
Y Y
Y Y
Y Y Y
Y
Y Y
Y Y
Y Y Y
Y Y
Y Y Y
Y Y Y
Y Y Y Y
11