Thermostat Control; Operating Instructions - Bionaire BCH9300 Instruction Manual

NOTES:
• Replace all batteries of a set at the same
time.
• Being careful not to bend or damage the
contact spring, clean the battery contacts
and the devices' contacts prior to installing
the batteries.
• Remove the batteries from the equipment
when it is not being used for an extended
period of time.
• Remove the used batteries promptly.
• Do not mix old and new batteries. Do not
mix alkaline, standard, (carbon-zinc), or
rechargeable batteries.
• Do not discard used batteries into household
trash containers. Contact your local
governments for disposal or recycling
practices in your area.
The remote control for this unit has the capability
of operating all control panel functions. Please
note this remote control will not work through
walls.
This Class B digital apparatus complies with
Canadian ICES-003. (Canada Only).

OPERATING INSTRUCTIONS

1. Place heater on a firm, level surface.
2. Plug heater into a standard outlet. Once
plugged in, the Power Light will illuminate,
and the room temperature will appear on the
LCD Display.
NOTE: Avoid overloading your circuit by not
using other high wattage appliances in the
same outlet.
3. Operate heater by pressing the Power
Button ( ) and selecting modes and
settings according to preference.
NOTE: Remove the plastic film from the
control panel before using (if included).
Power Button
Press the Power Button (
on. Once on, the heater will run in the Max Heat
mode and the Stay On icon will appear on the
LCD Display. Press the Power Button (
manually turn off the heater at any setting.
NOTE: The Power Light will remain illuminated
while unit is plugged in.
Mode Selection
Select your desired heat settings by pressing the
corresponding buttons as located on your heater
or remote control. An indicator light will illuminate
next to each button to indicate that the selected
setting/mode is activated.
) to turn the heater
) to
Fan Only Setting
Press the Fan Only Button to run the heater
without heat output. The Stay On icon will
appear on the LCD Display.
/
Setting
Press the /Heat & $ave™ Button to activate
the energy efficient Mode. The heater will now
cycle between high and low heat settings to
provide heat. The Stay On icon will appear on
the LCD Display.

Thermostat Control

Your heater is equipped with a digital thermostat
that allows you to set your heater to the desired
comfort level by pressing the Thermostat Button
( ) on the control panel or remote control:
NOTE: The Thermostat icon (
on the LCD Display.
To preset a comfort level, press the Thermostat
Button ( ) to adjust the temperature from 18°C
to 30°C (Default: 18°C, and each press of the
button will scroll through the next temperature
level). The LCD Display will show the selected
temperature reading. When the preset
temperature is reached, the heater will shut off
and cool down for 15 seconds. When the room
temperature drops below the preset
temperature, the heater will automatically turn on
again to maintain the preset temperature level.
Frost Guard Setting
Your heater is equipped with a Frost Guard/
FrostProtect™ setting. The heater will turn on
automatically when the room temperature drops
below 5°C. To activate Frost Guard setting,
press the Thermostat Button to select 5°C (scroll
through after temperature level 30°C) and the
Frost Guard icon (
Display.
NOTE: It is normal for the heater to cycle on and
off to maintain the preset temperature. Raise the
thermostat setting to prevent the heater from
cycling. When the preset temperature is reached
or when the heater is shut off, the fan will run for
15 seconds without heat. This cool down
process ensures an accurate and consistent
temperature reading.
NOTE: To shut the heater off at any setting,
press and hold the Power Button (
seconds. The heater will cool down for 15
seconds, and the Fan Only indicator light will
blink in Green until cool down is completed. The
heater will return to Standby mode with room
temperature shown on the LCD Display. The
digital thermostat has memory; it will remember
the last temperature setting before the heater is
turned off. However, if the heater is unplugged,
the digital thermostat will no longer remember
4
) will appear
) will appear on the LCD
) for 2