Output Definitions - First Alert FA168C Programming Manual

80 OUTPUT DEFINITIONS

Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you
enter the data during the displays and prompts that appear in sequence.
Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes.
2. For Powerline Carrier devices (plcd), field 27 must be programmed with a House Code.
3. Tampers of expansion units cannot be used to operate devices.
Output Activation Type and Detail
Function
Activated by Zone List
Number
0=delete (ZL)
(V20P=1-48)
1=zn list 1-8 = list
(V15P=1-24)
2=zn type
3=zn no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
ZONE TYPE/SYSTEM OPERATION – Choices for Zone Types are:
00 = Not Used 05 = Trouble Day/Alarm Night
01 = Entry/Exit#1 06 = 24 Hr Silent
02 = Entry/Exit#2 07 = 24 Hr Audible
03 = Perimeter 08 = 24 Hr Aux
04 = Interior Follower 09 = Fire
Choices for System Operation are:
20 = Arming–Stay
21 = Arming–Away
22 = Disarming (Code + OFF)
31 = End of Exit Time
32 = Start of Entry Time
33 = Any Burglary Alarm
36 = **At Bell Timeout***
Partition
Number
Zone Type Zone No.
(P)
(ZT) (ZN)
(if using ZT trig)
(see table 00=none
0 = any
below) 01-64
1 = partition 1
2 = partition 2
3 = common
10 = Interior w/Delay
12 = Monitor Zone
14 = Carbon Monoxide
16 = Fire w/Verification
23 = No Alarm Response
38 = Chime
39 = Any Fire Alarm
40 = Bypassing
41 = **AC Power Failure
42 = **System Battery Low
43 = Communication Failure 67 = Bell Failure
68 = TELCO Line Fault
Event (for zone list/activated by)
By Zone List By Zone No.
0 = restore 0 = restore
1 = alarm 1 = alrm/flt/trbl
2 = fault
3 = trouble
24 = Silent Burglary
77 = Keyswitch
90-93 = Configurable
52 = Kissoff
54 = Fire Zone Reset
58 = Duress
60 = AAV Trigger
** Use 0 (any) for Partition No. (P) entry.
66 = Function key†
*** Or at Disarming, whichever occurs earlier.
† Use *57 Menu mode to assign the function key.
†† Duration is set in program field *177.
78 = keyswitch red LED†††
††† Device action not used for these choices.
79 = keyswitch green LED†††
– 11 –
Action Output
0 = off Number
1 = close 2 secs
2 = stay closed FA168C:
3 = pulse 1-18
4 = toggle
5 = duration 1 FA148CP:
††
6 = duration 2 1-8, 17, 18
††
Note: In normal operation mode:
Code + # + 7 + NN Key Entry starts Device
Code + # + 8 + NN Key Entry stops Device
Device
Type
R = relay
T = trigger
X = X10