Cross Zone Timer; Option Selection - First Alert FA168C Programming Manual

67 RF XMTR LOW BAT REPORT CODE
CANCEL REPORT CODE
68
RESTORE REPORT CODES ( 70 – 76)
70 ALARM RESTORE RPT CODE
71 TROUBLE RESTORE RPT CODE
72 BYPASS RESTORE RPT CODE
73 AC RESTORE RPT CODE
74 LOW BAT RESTORE RPT CODE
75 RF XMTR LO BAT RST RPT CODE
76 TEST RESTORE RPT CODE
OUTPUT AND SYSTEM SETUP ( 77 – 93)
77 DAYLIGHT SAVINGS TIME
START\END MONTH
78 DAYLIGHT SAVINGS TIME
START\END WEEKEND
AUTO STAY ARM
84

CROSS ZONE TIMER

85
This option not for use in UL installations.
CANCEL VERIFY
86
87 MISC. FAULT DELAY TIME
(used with Configurable Zone Types "digit 6")
89 EVENT LOG FULL REPORT CODE
90 EVENT LOG ENABLES
91

OPTION SELECTION

92 PHONE LINE MONITOR ENABLE
UL: see Inst. Instructions for requirements
93 No. OF REPORTS IN ARMED PERIOD
PER ZONE (Swinger Suppression)
| [00]
| [00]
[0]
| [00]
| [00]
| [00]
| [00]
| [00]
| [00]
0 = Disabled
| [4][10]
1-12 = January-September (1 = Jan, 2 = Feb, etc)
#+10 = October; #+11 = November; #+12 = December
0 = disabled, 1 = first, 2 = second, 3 = third
| [1][5]
4 = fourth, 5 = last, 6 = next to last, 7 = third to last
0 = no, 1 = partition 1 only
[0]
2 = partition 2 only, 3 = both partitions
0 = 15 seconds
[0]
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes
(assign cross zones on zone list 4, with *81 Menu mode)
0 = no, 1 = yes
[0]
0 = 15 seconds
[0]
1 = 30 seconds
2 = 45 seconds
3 = 60 seconds
4 = 90 seconds
5 = 2 minutes
See box on previous page for report code entries.
| [00]
0 = None; 1 = Alarm/Alarm Restore
[3]
2 = Trouble/Trouble Restore;
4 = Bypass/Bypass Restore;
NOTE : System messages are
8 = Open/Close. Example: To select "Alarm/Alarm
logged when any non-zero
Restore", and "Open/Close", enter 9 (1 + 8); To select
selection is made.
all, enter #15.
0 = None
[8]
1 = Local Lockout
2 = Sounder Delay
E.g. (multiple choice): for AAV (4) plus Exit Delay restart
(8) enter # + 12; for all (1 + 2 + 4 + 8), enter # + 15.
Digit 1:: 0 = disabled, 1-15 = 1 min - 15 min
[0,0]
Digit 2:
0 = Keypad display when line is faulted
1 = Keypad display plus keypad trouble sound
2 = Same as "1", plus programmed output device
STARTS. If either partition is armed, external sounder
activates also. NOTE: Output Device must either be
programmed to be STOPPED in field 80 or
STOPPED by Code + # + 8 + output number.
0 = Unlimited Reports; 1 = 1 report; 2 = 2 reports
[0]
UL: must be "0"
– 5 –
See box on previous page.
UL: must be enabled if wireless devices are used
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
See box on previous page.
UL: must be enabled if wireless devices are used
See box on previous page.
6 = 2-1/2 min
7 = 3 min
8 = 4 min
9 = 5 min
#+10 = 6 min
#+11 = 7 min
6 = 2-1/2 min
7 = 3 min
8 = 4 min
9 = 5 min
#+10 = 6 min
#+11 = 7 min
UL: may only be used on non-burglar alarm/ non-fire alarm
zones when used in fire and/or UL burglar alarm installation
4 = AAV UL: do not use AAV
8 = Exit Delay Restart
(#+10 = 10 min; #+11 = 11 min; #+12 = 12 min;
#+13 = 13 min; #+14 = 14 min; #+15 = 15 min)
#+12 = 8 min
#+13 = 10 min
#+14 = 12 min
#+15 = 15 min
#+12 = 8 min
#+13 = 10 min
#+14 = 12 min
#+15 = 15 min