Page 1
Revision 3 April 2012 Owner’s Manual Serial Number Here Date of Purchase www.batcafitness.com Omega 4 Owner’s Manual 1207 New Hope Road, Raleigh, NC - 919.255.1233 - www.batcafitness.com...
Page 2
Instructions Congratulations on the purchase of your new Batca Omega 4. This gym will provide you with a lifetime of enjoyment to meet your strength training needs. Batca Fitness Systems strives to build the best quality gyms and to package these gyms in such a way to avoid any damage during shipping.
Page 3
ITEM PART NUMBER DESCRIPTION QTY. PART NUMBER DESCRIPTION QTY. BFP-10863 Leg Ext/Leg Curl Frame BFP-10949 Omega 4 Base Hub BFP-10947 Bearing Housing J Brace BFP-10951 Mid Row/Lat Pull Base BFP-52159 Anti-Deflection Plate BFP-10959 Chest Press/Pec Fly Base BFP-52164 Anti-Deflection Plate...
Page 5
Weight Stack to Free ITEM PART NUMBER DESCRIPTION QTY. Floater 146 BFP-52137 Head Pad Accessories 147 BFP-52136 Back Pad With Lumbar 148 BFP-52130 Large Bottom Pad ITEM NO. PART NUMBER DESCRIPTION QTY. BFM-51173 Weight Stack Pull Pin www.batcafitness.com Omega 4 Owner’s Manual...
Page 6
Batca Fitness Systems Omega 4 Owner's Manual...
Page 7
Bolt Length Note: Bolt length is measured from the underside of the head of the bolt. www.batcafitness.com Omega 4 Owner’s Manual...
Page 8
Batca Fitness Systems Omega 4 Owner's Manual...
Page 10
DO NOT TIGHTEN BOLTS UNTIL STEP 4 Figure 1 Item # Part # Description BFP-10949 Omega 4 Base Hub BFP-10951 Mid Row/Lat Pull Base BFP-10959 Chest Press/Pec Fly Base Every place that a BFP-10956 Leg Ext/Leg Curl Base...
Page 11
BFP-51756 SHCS 3/8” x 5 1/4” there is to be a 3/8” CURVED WASHER BFH-50204 3/8” Curved Washer 3/8” FLAT WASHER. instead of a BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Page 12
BFP-51756 SHCS 3/8” x 5 1/4” tube there is to be a 3/8” CURVED BFH-50204 3/8” Curved Washer WASHER instead of a 3/8” FLAT BFH-50146 3/8” Flat Washer WASHER. BFH-50157 3/8” Nylock Batca Fitness Systems Omega 4 Owner's Manual...
Page 13
Top Weight Plate BFM-50256 Weight Stack Plate BFM-51173 Weight Stack Pull Pin BFP-52143 Rubber Donut BFH-51747 SHCS 3/8” x 3” All Flat Washers and Nylocks are BFH-50146 3/8” Flat Washer 3/8” unless otherwise noted. BFH-50157 3/8”Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Page 14
Step 6. Item # Part # Description BFP-10963 Leg Press Base Connector BFP-51747 SHCS 3/8” x 3” All Flat Washers and Nylocks are BFH-50146 3/8” Flat Washer 3/8” unless otherwise noted. BFH-50157 3/8” Nylock Batca Fitness Systems Omega 4 Owner's Manual...
Page 15
Top Weight Plate BFM-50256 Weight Stack Plate BFM-51173 Weight Stack Pull Pin BFP-52143 Rubber Donut BFP-51747 SHCS 3/8” x 3” All Flat Washers and Nylocks are 3/8” BFH-50146 3/8” Flat Washer unless otherwise noted. BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Page 16
Figure 7 Item # Part # Description BFP-52138 Shroud With Logo Shroud All Flat Washers and Nylocks are 3/8” BFM-50444a unless otherwise noted. BFP-52340 SHCS 3/8” x 3/4” 111 BFH-50146 3/8” Flat Washer Batca Fitness Systems Omega 4 Owner's Manual...
Page 17
Small Aluminum End Cap BFP-50620 BHSCS 3/8” x 1” 106 BFP-51756 SHCS 3/8” x 5 1/4” All Flat Washers and Nylocks are 3/8” 110 BFH-50204 3/8” Curved Washer unless otherwise noted. 112 BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Page 18
SHCS 5/16” x 1/2” BFP-51752 SHCS 3/8” x 2 1/4” All Flat Washers and Nylocks are 3/8” BFP-51750 SHCS 3/8” x 2 3/4” unless otherwise noted. 111 BFH-50146 3/8” Flat Washer 112 BFH-50157 3/8” Nylock Batca Fitness Systems Omega 4 Owner's Manual...
Page 19
BFP-10831 Upper Pec Arm (Left) BFP-10830 Upper Pec Arm (Right) Foot Assist BFP-10825rev1 All Flat Washers and Nylocks are 3/8” BFP-51699 Axle unless otherwise noted. BFP-51696 Small Aluminum End Cap BFH-50620 BHSCS 3/8” x 1” www.batcafitness.com Omega 4 Owner’s Manual...
Page 20
BFH-50204 3/8” Curved Washer 3/8” CURVED WASHER there is to be a 3/8” FLAT WASHER. instead of a BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems Omega 4 Owner's Manual...
Page 21
Chest Press Chrome Seat Adjustment BFH-50210 Gas Spring BFP-51752 SHCS 3/8” x 2 1/4” All Flat Washers and Nylocks are BFP-51750 SHCS 3/8” x 2 3/4” 3/8” unless otherwise noted. BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Page 22
Bearing Housing J Brace BFP-52159 Anti-Deflection Plate BFP-52164 Anti-Deflection Plate BFP-51748 SHCS 3/8” x 3 1/4” All Flat Washers and Nylocks are 111 BFH-50146 3/8” Flat Washer 3/8” unless otherwise noted. 112 BFH-50157 3/8” Nylock Batca Fitness Systems Omega 4 Owner's Manual...
Page 23
SHCS 3/8” x 2 3/4” 3/8” CURVED WASHER there is to be a BFP-51756 SHCS 3/8” x 5 1/4” 3/8” FLAT WASHER. instead of a BFH50204 3/8” Curved Washer 111 BFH-50146 3/8” Flat Washer 112 BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Support Plate BFP-51696 Small Aluminum End Cap 2 BFH-50620 BHSCS 3/8” x 1” BFP-52374 FHSCS 3/8” x 2 3/4” All Flat Washers and Nylocks are 3/8” BFH-50146 3/8” Flat Washer unless otherwise noted. BFH-50157 3/8” Nylock www.batcafitness.com Omega 4 Owner’s Manual...
Clean guide rods with a lint-free cloth and apply a thin layer of silicone lubricant (Part # BFH- 50262) to each guide rod. This will ensure a glass smooth performance from your weight stack. www.batcafitness.com Omega 4 Owner’s Manual...
Note: If the top plate raises off of the second plate in the weight stack, then the cable ten- sion is too tight. You will need to take some of the tension out to lower the Top plate flush with the second plate. Batca Fitness Systems Omega 4 Owner's Manual...
Page 43
Note: If the top plate raises off of the second plate in the weight stack, then the cable ten- sion is too tight. You will need to take some of the tension out to lower the Top plate flush with the second plate. www.batcafitness.com Omega 4 Owner’s Manual...
Preventive Maintenance Batca Fitness Systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below should be followed.
Improper installation, improper assembly or follow-up maintenance along with installation of parts or accessories not originally intended for products of Batca Fitness Systems are also not covered by this warranty. Only genuine Batca parts should be used for replacement, repair, and maintenance for this warranty to apply.
Page 46
Layout Diagram The Omega 4 without Leg Press has a layout dimension of 8’-1” (Length) x 9’-5” (Width) x 7’-1” (Height). The Omega 4 with Leg Press has a layout dimension of 9’-0” (Length) x 9’-5” (Width) x 7’-1” (Height). There should be minimum of 18”, preferably 24”, or working space around the entire unit.
Need help?
Do you have a question about the omega 4 and is the answer not in the manual?
Questions and answers