Selecting channel / frequency setting ............23 Setting the output channel ................24 Setting the output frequency ................24 Switching the modulator off or on ..............24 Adjusting the output levels of the channel strips ..........25 - 2 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 3
Setting the scrambling ..............37 Setting the PID monitoring ..............38 Configuring the CA module ..............38 Setting the station filter ..............39 6 Final procedures .....................41 7 Channel and frequency tables .................42 - 3 - HDMT 1000 ASI LAN / HDMT 1001 C...
At the end of its service life, please take your device to one of these public collection facilities for proper disposal. - 4 - HDMT 1000 ASI LAN / HDMT 1001 C...
General information Packing contents 1 cassette HDMT 1000 ASI LAN or HDMT 1001 C 2 HF cables 1 CD (assembly instructions) 1 Brief assembly instructions Meaning of the symbols used Important note —> General note Technical data The de EU directives: 2006/95/EC, 2004/108/EC Unless otherwise noted all values are specified as “typical”.
Receiving stage SAT input ”A“ CA module Transport stream 1 "A" TS ASI ASI input TS B Receiving stage Transport stream 2 SAT input ”B“ "B" - 6 - HDMT 1000 ASI LAN / HDMT 1001 C...
“B” and the transport stream from the ASI input “TS ASI” via the ASI output. Modulator Transport stream 1 "A" Combiner HF output Modulator Transport stream 2 "B" TS ASI ASI input ASI output - 7 - HDMT 1000 ASI LAN / HDMT 1001 C...
(LED illuminates) or off. The integrated TPS module (Transport Stream Processing) processes the data of the transport streams. - 8 - HDMT 1000 ASI LAN / HDMT 1001 C...
“V 41” or higher. You can find the current op- BE-Flash” and the current assembly instructions on the website “www.gss.de”. The cassette is designed for use in the following head-end stations: und PST 19-1.
Page 10
Changing the operator ID (CAT) Some network operators transmit an operator ID in the data stream (e.g. visAvision). By changing the CAT the operator ID can be adjusted to the cur- rent demands. - 10 - HDMT 1000 ASI LAN / HDMT 1001 C...
19” cabinet, make sure the connections leading in and out for the 19” cabinet are made using cable terminals. The attenuation of shielding of the connection lines for ASI and antenna must meet the requirements for “Class A”. CLASS - 11 - HDMT 1000 ASI LAN / HDMT 1001 C...
The operating software of the cassette can be updated via the 9-pin D-SUB socket “RS-232” using a PC or notebook and the software “BE-Flash”. You can find the current operating software on the website “www.gss.de”. - 12 - HDMT 1000 ASI LAN / HDMT 1001 C...
(top) of the CA module. with the top side of the CA module facing the top side of the cassette. and contact it to the common interface. - 13 - HDMT 1000 ASI LAN / HDMT 1001 C...
The key pad on the head-end station is used to scroll through the menus step- by-step: scrolls forward through the menus. select parameters in the menus. selects sub-menus. scrolls backward through the menus. saves all entries. - 14 - HDMT 1000 ASI LAN / HDMT 1001 C...
Switch on the channel strip (modulator) if necessary (page 24). For each switched on. Status LED Status LED Channel strip "B" Channel strip "A" A” and “B” if the difference in level is 1 dB (page 25). - 15 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 18 Bx 4 LINE Line A / Line B Line A <= => Line B Bx 4A OUTPUT Channel Channel / Freq. Bx 4A OUTPUT on / off - 16 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 17
Channel strip “B“ Bx 4A normal / inverse 64-QAM normal 4 … 256 Bx 4A STUFFING SR=6900 1000 … 7500 Bx 4A FAILURE Null Packets … Single Carrier Null Packets - 17 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 18
Bx 4A FACTORY Bx 4A FACTORY zurücksetzen und speichern reset to factory defaults Defaults => STORE => M and store - 18 - HDMT 1000 ASI LAN / HDMT 1001 C...
*) Die angezeigte Information ist nächster Service abhängig vom verwendeten next service CA-Modul. The information displayed is dependent on the CA module used. Page 17 - 19 - HDMT 1000 ASI LAN / HDMT 1001 C...
“Box 4” stands for slot 4 ”COFDM-TPM” Type of cassette ”V 12” Software version of the cassette button. —> The “Selecting the input signal path” – “INROUTE” menu is activated. - 20 - HDMT 1000 ASI LAN / HDMT 1001 C...
—> The “Selecting the channel strip” – “LINE” menu is activated (page 23). button. —> The “Setting the ASI transfer rate” – “ASI RATE” menu is activated. - 21 - HDMT 1000 ASI LAN / HDMT 1001 C...
The data packets of the user data are collected to a great data packet in the transport stream. —> Seting “burst” The data packets of the user data are spaced out evenly in the transport stream. - 22 - HDMT 1000 ASI LAN / HDMT 1001 C...
For programming in these channel ranges and in the frequency ranges below of the QAM output signal by removing stations. Bx 4A OUTPUT Channel to select channel setting “Channel” or frequency setting “Freq.”. - 23 - HDMT 1000 ASI LAN / HDMT 1001 C...
—> The switched off modulator is indicated by “ - - - “ in the display instead of the channel or frequency display. off” use the to switch it “on”. - 24 - HDMT 1000 ASI LAN / HDMT 1001 C...
“station search” mode. Please wait until the process has finished. OK” is displayed. If “– – present. Check the configuration of the antenna system and the head-end sta- tion as well as the preceding settings of the cassette. - 25 - HDMT 1000 ASI LAN / HDMT 1001 C...
DVB-T data stream using “Quadrature Amplitude Modulation” (QAM). The robust “High Priority” data stream (HP) with a lower data rate is modulated onto the more sensitive “Low Priority” data - 26 - HDMT 1000 ASI LAN / HDMT 1001 C...
“A” and therefore cannot be set in channel strip “B”. Programming channel strip “B” the transport stream coming from the ASI input can be processed only. - 27 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 28
/ off Press the button. name and station type. —> Pressing the button all stations can be activated or deactivated. play: “FILTER no Service”. components connected to the ASI input. - 28 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 29
PAT and SDT tables are updated. PROGRAM Filter on” menu the station filters switched on can be switched “off” using the buttons if necessary. - 29 - HDMT 1000 ASI LAN / HDMT 1001 C...
QAM modulation (“4 256”). output QAM modulation of >64 QAM places a large burden on the reception of the converted output signal can be affected. - 30 - HDMT 1000 ASI LAN / HDMT 1001 C...
. The value set corresponds to the new output symbol rate. Increasing the value of “Number 1”. —> The “Number 1” can be increased to any value up to 7500. - 31 - HDMT 1000 ASI LAN / HDMT 1001 C...
Bx 4A FAILURE Null Packets Use the buttons to set the output signal required. button. —> The “Setting the transport stream ID and the ORGNET-ID” – “TS/ONID” menu is activated. - 32 - HDMT 1000 ASI LAN / HDMT 1001 C...
NIT. This process may take a few seconds. QAM cassettes. The other cassettes cas- settes in the NIT menu changes to “on”. The display shows: “read … / copy …”. - 33 - HDMT 1000 ASI LAN / HDMT 1001 C...
—> If you try to change the network/operator identification (operator ID) of not modified” appears in the display. button. —> The “Deleting a PID” – “DROP” menu is activated. - 34 - HDMT 1000 ASI LAN / HDMT 1001 C...
PID (“–> 0000”). button to set the cursor to “off” and rename the PID using the buttons (“on”). button. —> The “Factory reset” – “FACTORY Default” menu is activated. - 35 - HDMT 1000 ASI LAN / HDMT 1001 C...
– Network/operator identification CAT is activated. —> By pressing the “Selecting the channel strip” via without saving the programmed data (page 23). —> If necessary set channel strip “B”. - 36 - HDMT 1000 ASI LAN / HDMT 1001 C...
—> In case of setting “scramble”: The “Setting the QAM modulaton” – “QAM” menu is activated (page 30). —> In case of setting “descramble”: The “Setting the PID monitoring” – “CA” menu is activated. - 37 - HDMT 1000 ASI LAN / HDMT 1001 C...
Bx 4A 01/03 MENU Information Meaning of the indicators: “Bx 4A A” “01/03” – The first of three menu items is activated. “MENU” – The menu of the CA module is activated. - 38 - HDMT 1000 ASI LAN / HDMT 1001 C...
– TV channel type “X” – Descrambling is set for the currently selected station. “04/09” – The 4th of 9 stations read is being displayed. “..” – Station name - 39 - HDMT 1000 ASI LAN / HDMT 1001 C...
Page 40
—> The filter is activated. The display shows the “Configuring the CA mod- ule” – “CA” menu. Bx 4A Menu <= => Edit button. —> The “Setting the QAM modulation” – “QAM” menu is activated (page 30). - 40 - HDMT 1000 ASI LAN / HDMT 1001 C...
Please regard the assembly instructions of the respective head-end station. —> In order to prevent interference within the head-end station and the cable compared to analogue cassettes. - 41 - HDMT 1000 ASI LAN / HDMT 1001 C...
C 68 850.00 C 29 538.00 C 39 618.00 C 49 698.00 C 59 778.00 C 69 858.00 C 30 546.00 C 40 626.00 C 50 706.00 C 60 786.00 - 42 - HDMT 1000 ASI LAN / HDMT 1001 C...
Need help?
Do you have a question about the HDMT 1000 ASI LAN and is the answer not in the manual?
Questions and answers