MEX-BT5100
Pin No.
Pin Name
93
VCC
94
A25
95
PTK4
96
RD
97
DQMLL
98
DQMLU
99
DQMUL
100
VSSQ
101
DQMUU
102
VCCQ
103
RD/WR
104
PTE7
105
NOR_CS
106
CS2
107
SD_CS
108
CSA
109
PTK3
110
CSB
111
EVOL_CLK
112
MAS_RST
113
SELF_PRCT
114
DISP_RST
115
VSSQ
116
TXDPLS
117
VCCQ
118
MAS_PW
119
DOOR_SW
120
ATT
121
TXDMNS
122
USB1D_SUSPEND
123
USB1_OVR_CRNT
124
USB2_OVR_CRNT
125
USB1DTXEL
126
USB1PWREN
127
USB2PWREN
128
SD_CKE
129
SD_RAS
130
PTJ1
131
SD_CAS
132
VSSQ
133
PTJ3
134
VCCQ
135, 136
PTJ4, PTJ5
137
VSS
138
SH_PW
139
VCC
140
DISP_PW
141
MAS_FLSW
142
DISP_FLSW
143
TDO
144
DRAK0
145
DACK
146
WAIT
147
RESETM
54
I/O
-
Power supply terminal (+1.9V)
O
Address signal output terminal
-
Not used
O
Read strobe signal output to the fl ash ROM and data bus interface
O
Write mask signal output to the SD-RAM and data bus interface
O
Write mask signal output to the SD-RAM and fl ash ROM
O
Write mask signal output to the SD-RAM
-
Ground terminal
O
Write mask signal output to the SD-RAM
-
Power supply terminal (+3.3V)
O
Read/write signal output to the SD-RAM
-
Not used
O
Chip select signal output to the fl ash ROM
O
Chip select signal output terminal
O
Chip select signal output to the SD-RAM
O
Chip select signal output to the data bus interface
-
Not used
O
Chip select signal output to the data bus interface
O
Serial data transfer clock signal output to the audio select
O
System reset signal output terminal
O
Power on/off control signal output terminal for the bluetooth section
O
System reset signal output to the front panel controller
-
Ground terminal
-
Not used
-
Power supply terminal (+3.3V)
State notifi cation signal input from the system controller
I
"H": state that can be communicated
Shutter of front panel open/close detection input terminal
I
"L": Shutter is open
I
Muting on/off control signal input terminal
-
Not used
-
Not used
I
Over current detection signal input terminal
I
Over current detection signal input terminal
-
Not used
O
Power on/off control signal output terminal
O
Power on/off control signal output terminal
O
Clock enable signal output to the SD-RAM
O
Row address strobe signal output to the SD-RAM
-
Not used
O
Column address strobe signal output to the SD-RAM
-
Ground terminal
-
Not used
-
Power supply terminal (+3.3V)
-
Not used
-
Ground terminal
State notifi cation signal output to the system controller
O
"H": state that can be communicated
-
Power supply terminal (+1.9V)
O
Communication interface signal output to the front panel controller
O
Flash writing mode detection signal output terminal
O
Flash writing mode detection signal output terminal
O
Data output terminal
Not used
-
Not used
-
Not used
I
Hardware wait request signal input terminal
I
Manual reset request signal input terminal
Description
Not used
Not used
Not used
"L": reset
Can not disc eject when input "H"
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used